Bedienungsanleitung Yaesu FT-450 (Seite 69 von 104) (Englisch)

444588

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

Page 67FT-450 OPERATION MANUAL

OPERATION ON ALASKA EMERGENCY FREQUENCY: 5167.5 kHZ

(

U.S. VERSION ONLY

)

Section 97.401(d) of the regulations governing amateur radio in the United States permit emergency amateur

communications on the spot frequency of 5167.5 kHz by stations in (or within 92.6 km of) the state of Alaska.

This frequency is only to be used when the immediate safety of human life and/or property are threatened, and

is never to be used for routine communications.

The FT-450 includes the capability for transmission and reception on 5167.5 kHz under such emergency condi-

tions.

Preparation

1. Press and hold the [F] button for one second to

enter the Menu mode. The “ ” icon will ap-

pear on the display.

2. Rotate the [DSP/SEL] knob to select the menu

item “EXT MNU”.

3. Press the [DSP/SEL] knob to enable adjustment

of this menu item. The “ ” icon will be blink-

ing.

4. Rotate the [DSP/SEL] knob to select “ON” to ex-

pand the menu items.

5. Press the [DSP/SEL] knob. The “ ” icon re-

turns to appear continuously.

6. Press and hold the [F] button for one second to

save the new setting and return to normal opera-

tion.

7. Press and hold the [F] button for one second to

enter the Menu mode again. The “ ” icon

will appear on the display.

8. Rotate the [DSP/SEL] knob to select the menu

item “EMERGEN”.

9. Press the [DSP/SEL] knob to enable adjustment

of this menu item. The “ ” icon will be blink-

ing.

10.Rotate the [DSP/SEL] knob to select “ON”.

11.Press the [DSP/SEL] knob. The “ ” icon re-

turns to appear continuously.

12.Press and hold the [F] button for one second to

save the new setting and return to normal opera-

tion.

Operation

1. Press the [MW/V/M] button, if necessary, to enter

the Memory mode. A memory channel number will

appear in display.

2. Rotate the [DSP/SEL] knob to select the emer-

gency channel (“MEM-EMG”), which is found be-

tween channels “MEM-P2U” and “US5-001.”

If you partitioned your memory channels into

Memory Groups via Menu Item “MEM GRP”, then

select the memory channel group “M-12-EM”

which is the emergency channel.

3. To exit from emergency channel and return to the

VFO mode, just press the [MW/V/M] button.

Note:

❒ The receive-mode CLARIFIER functions normally while using this frequency, but variation of the transmit

frequency is not possible. Activation of “MEM-EMG” or “M-12-EM” does not enable any other out-of-amateur-

band capability on the transceiver. The full specifications of the FT-450 are not necessarily guaranteed on

this frequency, but power output and receiver sensitivity should be fully satisfactory for the purpose of emer-

gency communication.

❒ In an emergency, note that a half-wave dipole cut for this frequency should be approximately 45’3” on each

leg (90’6” total length). Emergency operation on 5167.5 kHz is shared with the Alaska-Fixed Service. This

transceiver is not authorized for operation, under the FCC’s Part 87, for aeronautical communications.

[

MW/V/M

]

button

[

DSP/SEL

]

knob

[

HOME/RCL

]

button

[

]

button

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yaesu FT-450 Seite 69

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info