674732
16
Zoom out
Zoom in
Vorherige Seite
1/102
Nächste Seite
HF/50 MH
Z
T
RANSCEIVER
FT-450D
O
PERATION
M
ANUAL
VERTEX STANDARD CO., LTD.
4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan
VERTEX STANDARD
US Headquarters
10900 Walker Street, Cypress, CA 90630, U.S.A.
YAESU UK LTD.
Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U.K.
VERTEX STANDARD HK LTD.
Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road,
Kwun Tong, Kowloon, Hong Kong
VERTEX STANDARD
(
AUSTRALIA
)
PTY., LTD.
Normanby Business Park, Unit 14/45 Normanby Road
Notting Hill 3168, Victoria, Australia
GENERAL FEATURE ........................................... 1
FRONT PANEL BUTTONS AND KNOBS ............ 2
DISPLAY INDICATIONS ....................................... 6
REAR PANEL JACKS ..........................................8
SUPPLIED MH-31A8J MICROPHONE ................. 9
ACCESSORIES & OPTIONS ............................. 10
INSTALLATION .................................................. 11
CONNESTION OF ANTENNA AND POWER SUPPLY .. 11
ABOUT COAXIAL CABLE ............................................... 12
GROUNDING ................................................................... 12
VL-1000 LINEAR AMPLIFIER INTERCONNECTIONS .. 13
INTERFACING TO OTHER LINEAR AMPLIFIER ........... 13
EASY OPERATION ............................................ 14
HOW TO USE THE
[
DSP/SEL
]
KNOB ............................ 15
MENU OPERATION ......................................................... 15
HOW TO USE THE
[
VOICE/C.S
]
SWITCH .................... 16
KEY DURATION SETTING .............................................. 17
RESETTING THE MICROPROCESSOR ........................ 18
RECEIVING ........................................................ 19
TUNING STEPS ............................................................... 19
CHANGE THE TUNING STEP
OF THE
[
MAIN DIAL
]
KNOB ..................... 19
CHANGE THE TUNING STEP
OF THE
[
DSP/SEL
]
KNOB ........................ 19
ABOUT THE
[
UP
]
/
[
DWN
]
BUTTONS
OF THE MH-31A8J ........... 20
CLARIFIER ....................................................................... 20
DIGITAL VOICE ANNOUNCEMENT ............................... 21
DIAL LOCK ....................................................................... 21
MY BANDS OPERATION ................................................ 22
MY MODES OPERATION ............................................... 23
DIGITAL VOICE RECORDER ......................................... 24
CONVENIENCE FEATURES ............................. 25
RECEIVER OPERATION
(FRONT END BLOCK DIAGRAM
) ......................................... 25
IPO/ATT
(ADJUST THE RECEIVING SENSITIVITY)
..................................
26
NOISE BLANKER
(INTERFERENCE REJECTION “SIGNALS WITHIN 3 kHz”)
........... 26
AGC
(TOOL FOR COMFORTABLE AND EFFECTIVE RECEPTION) .........
27
CONTOUR
(INTERFERENCE REJECTION “SIGNALS WITHIN 3 kHz”)
........... 28
SHIFT
(INTERFERENCE REJECTION “SIGNALS WITHIN 3 kHz”)
........... 29
WIDTH
(INTERFERENCE REJECTION “SIGNALS WITHIN 3 kHz”)
........... 30
NOTCH
(INTERFERENCE REJECTION “SIGNALS WITHIN 3 kHz”)
........... 31
DNR
(INTERFERENCE REJECTION “SIGNALS WITHIN 3 kHz”)
........... 32
RF GAIN ........................................................................... 33
Using the Automatic Antenna Tuner ............... 34
ATU Operation ................................................................. 34
About ATU Operation ....................................................... 35
SSB/AM MODE TRANSMISSION .....................36
TX METER SELECTION ................................................. 37
TX POWER ADJUSTMENT ............................................ 37
TRANSMITTER TIME-OUT TIMER (TOT) ...................... 38
MICROPHONE GAIN LEVEL ADJUSTMENT ................ 39
DSP MICROPHONE EQUALIZER .................................. 40
AUTOMATIC TX/RX SWITCHING
USING VOICE CONTROL (VOX) ........................... 41
MONITOR ........................................................................ 42
SPLIT-FREQUENCY OPERATION ................................. 43
QUICK SPLIT OPERATION ............................................ 43
VOICE MEMORY (SSB/AM/FM MODES) ...................... 44
CW MODE OPERATION .................................... 46
SETUP FOR STRAIGHT KEY
(AND STRAIGHT KEY EMULATION) OPERATION ..... 46
USING THE BUILT-IN ELECTRONIC KEYER ................ 47
CW SPOTTING (ZERO-BEATING) ................................. 49
USING CW REVERSE .................................................... 49
CW DELAY TIME SETTING ............................................ 50
CW SIDETONE VOLUME LEVEL SETTING .................. 50
CW PITCH ADJUSTMENT .............................................. 51
CW TRAINING FEATURE ............................................... 51
BEACON FEATURE ........................................................ 52
FM MODE OPERATION ..................................... 54
BASIC OPERATION ........................................................ 54
REPEATER OPERATION ................................................ 55
TONE SQUELCH/DCS OPERATION .............................. 56
TONE SEARCH SCANNING ........................................... 57
MEMORY OPERATION ...................................... 58
CONVENIENT MEMORY FUNCTIONS .......................... 58
MEMORY GROUPS......................................................... 59
REGULAR MEMORY OPERATION ................................ 60
MEMORY STORAGE ................................................ 60
MEMORY CHANNEL RECALL ................................. 60
ERASING MEMORY CHANNEL DATA ..................... 61
MEMORY TUNE OPERATION .................................. 61
LABELING MEMORIES ............................................ 62
HOME CHANNEL MEMORIES ....................................... 64
HOME CHANNEL RECALL ....................................... 64
HOME CHANNEL FREQUENCY CHANGE ............. 64
QMB (QUICK MEMORY BANK) ...................................... 65
STORAGE ................................................................. 65
RECALL ..................................................................... 65
SCANNING OPERATION ................................... 66
VFO AND MEMORY SCANNING .................................... 66
PREPARATION ......................................................... 66
VFO/MEMORY SCAN ............................................... 67
PROGRAMMABLE MEMORY SCANNING
(PMS) ........ 68
OPERATION ON ALASKA
EMERGENCY FREQUENCY: 5167.5 kHz
(U.S. Version Only) ........... 69
MISCELLANEOUS SETTINGS .......................... 70
DISPLAY SETTING .......................................................... 70
BEEPER SETTING .......................................................... 71
BEEP VOLUME ......................................................... 71
BEEP TONE .............................................................. 72
AUTOMATIC POWER-OFF (APO) .................................. 73
TABLE OF CONTENTS
Disposal of your Electronic and Electric Equipment
Products with the symbol (crossed-out wheeled bin) cannot be disposed as household waste.
Electronic and Electric Equipment should be recycled at a facility capable of handling these items and
their waste byproducts.
In EU countries, please contact your local equipment supplier representative or service center for
information about the waste collection system in your country.
Page 1FT-450D OPERATION MANUAL
TABLE OF CONTENTS
RTTY (RADIO TELETYPE) OPERATION .......... 74
SETTING UP FOR RTTY OPERATION .......................... 74
BASIC SETUP ................................................................. 74
PACKET OPERATION ....................................... 75
PACKET SETUP
(INCLUDING SUBCARRIER FREQUENCY) ........... 75
BASIC SETUP ................................................................. 75
MISCELLANEOUS AFSK-BASED
DATA MODES ................. 76
MENU MODE ..................................................... 78
USING THE MENU .......................................................... 78
MENU MODE RESET ...................................................... 78
CLONING ........................................................... 88
GENERAL FEATURES
Super Compact HF Transceiver with IF-DSP
Built-in ATU (automatic antenna tuner)
Great HF radio performance, with uncomplicated operation, is realized with the very small FT-450D HF
transceiver.
HF + 50 MHz with 100 Watts output all mode operation
Small, compact and light-weight HF radio, 9 (W) x 3.3 (H) x 8.5 (D) in, 8.8 lb
Large 9-segment LCD display characters, provide easily read frequency indication
Black-Nega type LCD
Illumination Button
Built-in IF DSP unit that performs all of the following functions:
Modulation and Demodulation
CONTOUR
MANUAL NOTCH
DNR
WIDTH (CW narrow 300 Hz operation available without any optional filters)
Microphone equalizer built in
Speech Processor
DSP VOX operation
Two Voice memory channels included
Frequency read out function
TCXO built-in
500 memory channels
IF SHIFT
IPO
20 dB ATT built-in
Clarifier
Electronic keyer built-in
Microphone and phone jacks on the front panel
FSK-RTTY TX operation
Long wire antenna can be used by the optional FC-40
INSTALLATION OF
OPTIONAL ACCESSORIES .................... 90
AUTOMATIC-MATCHING 200-MEMORY
ANTENNA TUNER FC-40 OPERATION ....................... 90
ACTIVE-TUNING ANTENNA SYSTEM
(ATAS-100/-120/120A) OPERATION .................... 92
CARRYING HANDLE MHG-1 INSTALLATION ............... 94
MOUNTING BRACKET
MMB-90 INSTALLATION ............................ 95
SPECIFICATIONS .............................................. 96
FCC NOTICE ...................................................... 98
Congratulations on the purchase of your Yaesu amateur transceiver! Whether this is
your first rig, or if Yaesu equipment is already the backbone of your station, rest assured
that your transceiver will provide many hours of operating pleasure for years to come.
Page 2 FT-450D OPERATION MANUAL
PHONES
KEY
F
RONT
P
ANEL
B
UTTONS
AND
K
NOBS
PHONE Jack
A 3.5 mm, 3-contact jack accepts ei-
ther monaural or stereo headphones
with 2 or 3-contact plugs. When a plug
is inserted, the loudspeaker is dis-
abled.
N
OTE:
When wearing headphones, we rec-
ommend that you turn the AF GAIN
levels down to their lowest settings
before turning power on, to minimize
the impact on your hearing caused by
audio “pops” during switch-on.
KEY Jack
This 3.5 mm, 3-contact
jack accepts a CW key or
keyer paddles (for the
built-in electronic keyer),
or output from an external
electronic keyer. Pinout is
shown below. Key up is 5
volts, and key down cur-
rent is 0.5 mA.
DSP Button
This button selects the DSP functions.
Available selections are CONTOUR,
NOTCH, DNR, and WIDTH.
IPO/ATT Button
This button selects the IPO or ATT feature. Available se-
lections are:
ATT:OFF/IPO:OFF ATT:OFF/IPO:ON
ATT:ON/IPO:OFF ATT:ON/IPO:ON
ATT:OFF/IPO:OFF
IPO: OFF, ATT: OFF
Attenuator is OFF, and the RF preamplifier amplifies
the incoming signal.
IPO: ON, ATT: OFF
Attenuator is OFF, and the received signal bypasses
the RF preamplifier, yielding a direct feed to the first
mixer.
IPO: OFF, ATT: ON
The received signal is reduced by 20 dB, and the RF
preamplifier amplifies the incoming signal.
IPO: ON, ATT: ON
The received signal is reduced by 20 dB, and the in-
coming signal bypasses the RF preamplifier, yielding a
direct feed to the first mixer.
The selection will be indicated in the Block Diagram on
the display.
ON/OFF Button
Press and hold in this button for one second
to turn the transceiver on or off.
NB Button
This button turns the IF Noise Blanker
on and off. Press this button to re-
duce short-duration pulse noise.
AGC Button
This button selects the AGC characteristics for the receiver.
Press and hold in this button for one second to disable the
AGC (for testing or weak-signal reception).
Do not use the plug except the 3.5-mm 3-pin type plug. If the plug in correct size is
not used the radio may be harmed or damaged.
Page 3FT-450D OPERATION MANUAL
F
RONT
P
ANEL
B
UTTONS
AND
K
NOBS
C.S/VOICE Button
Press this button to activate one of the 52 functions, which
can be assigned via Menu Item “PNL-C.S.”
Press the
[
F
]
button followed by this button to announce the
current operating frequency (with resolution to the displayed
100 Hz digit) and operating mode.
TUNE Button
Press this button momen-
tarily to toggle the Internal
Automatic Antenna Tuner
on/off.
Press and hold in this but-
ton to begin the automatic
Tuning.
F Button
Press this button to activate the alternate
key functions of the six command buttons
located on the upper right corner of the
front panel.
Press and hold this button for one sec-
ond to engage the “Menu” mode.
METER/DIM Button
Press this button to change the meter
function in the transmit mode as fol-
lows.
PO ALC SWR PO
PO: Indicates the average power
output level.
ALC: Indicates the relative ALC volt-
age.
SWR: Indicates the Standing Wave
Ratio (Forward/Reflected).
Press the
[
F
]
button followed by this
button to enable adjustment of the
display dimmer level by the
[
DSP/
SEL
]
knob. When the adjustment is
complete, press this key again.
RCL/HOME Button
Press this button to recall the Quick Memory Bank
memory for operation. Press this button again to
return to the VFO or Memory mode.
Press the
[
F
]
button followed by this button to recall
the “Home” (favorite frequency) channel.
SPLIT/STEP Button
Press this button to activate split fre-
quency operation between VFO-A,
used for reception and VFO-B, used
for transmission (or vice versa).
Press the
[
F
]
button followed by this
button to enable setting of the fre-
quency step with the
[
DSP/SEL
]
knob.
When the selection is complete, press
this key again.
V/M/MW Button
This button toggles frequency control between the
VFO and the memory system.
Press the
[
F
]
button followed by this button to copy
the current operating data from the VFO into the cur-
rently selected memory channel.
STO/VOX Button
Press this button to copy the operating in-
formation (frequency, mode, bandwidth,
and also repeater direction/shift frequency
and CTCSS functions on the FM mode) into
the Quick Memory Bank.
Press the
[
F
]
button followed by this button
to activate the VOX (voice-actuated trans-
mitter switching) feature in the SSB, AM,
and FM modes.
SCAN/PMS Button
Press this button to initiate the
upward scanning of VFO fre-
quencies or memory chan-
nels.
Press the
[
F
]
button followed
by this button to engage the
Programmable Memory Scan,
(PMS) which limits scanning
within a particular frequency
range.
Front Feet
The two front feet allow the transceiver to be
tilted upward for better viewing.
Page 4 FT-450D OPERATION MANUAL
PHONES
KEY
F
RONT
P
ANEL
B
UTTONS
AND
K
NOBS
CLAR Button
Pressing this button activates the Clarifier,
to allow temporarily offsetting the receive
frequency. When the Clarifier is active, you
may offset the receive frequency by adjust-
ing the
[
MAIN DIAL
]
knob.
SHIFT Knob
This knob shifts the IF DSP passband
to reduce an interfering signal which
is inside the IF passband.
DSP/SEL Knob
This knob is used to select functions
depending on the situation.
G Frequency Tuning
G Memory Channel Selection
G DSP Setting
G Menu Mode Selection
MODE/MODE Button
These buttons select the operating
mode.
KEYER Button
This button toggles the in-
ternal CW keyer on and off.
MIC Jack
This 8-pin jack accepts input from
a supplied MH-67A8J Hand Micro-
phone.
(viewed from front panel)
Page 5FT-450D OPERATION MANUAL
F
RONT
P
ANEL
B
UTTONS
AND
K
NOBS
A=B Button
Press this button momentarily to transfer data from VFO-A fre-
quency (or a recalled memory channel) to VFO-B, overwriting
the previous contents in VFO-B. Use this key to set both VFO-A
and VFO-B to the same frequency and mode.
A/B Button
This button toggles the frequency
control between VFO-A and VFO-B.
FAST Button
Pressing this button will increase or decrease the tuning rate of
the
[
MAIN DIAL
]
knob by a factor of ten and also increase or
decrease the tuning rate of the
[
DSP/SEL
]
knob by a factor of
two.
LOCK Button
This button toggles the locking of the
[
MAIN DIAL
]
knob and some
switches, to prevent accidental frequency changes.
Advice: You may select the locking schemes via the Menu Mode.
Term Explanation: The Menu Mode permits you to make small changes
in the parameters of many of the functions of the FT-450D. You can cus-
tomize the operations to your personal preferences.
MAIN DIAL Knob
This knob adjusts the operating frequency in the SSB/CW/DATA modes.
You may change the knob’s function to also adjust frequency in AM/FM
mode via the Menu Mode.
When the Clarifier is activated, this knob adjusts the receiver offset
frequency.
AF GAIN
This knob sets the receiver’s audio
volume level. Typically, you will op-
erate with this control set between
the 9 o’clock and 10 o’clock posi-
tions.
SQL/RF GAIN Knob
In the factory default, this knob ad-
justs the gain of the receiver’s RF
and IF stages. Using Menu Item
“SQL/RFG”, this knob may be
changed to function as a Squelch
control, which may be used to si-
lence background noise when no sig-
nal is present.
BAND/BAND Button
These buttons select the operating band.
Page 6 FT-450D OPERATION MANUAL
PHONES
KEY
D
ISPLAY
I
NDICATIONS
DSP Graphic Display
: The peak position of the CONTOUR Filter is depicted graphically here when the CONTOUR
Filter is activated.
: The null position of the IF Notch Filter is depicted graphically here when the IF Notch Filter
is activated.
: Indicates the Noise Reduction level of the Digital Noise Reducer.
: Indicates the bandwidth of the DSP IF filter.
: Indicates the peak position of the DSP IF filter.
Meter
While receiving, the received signal strength is displayed.
While transmitting, the meter displays PO, ALC, or SWR (determined by the
[
METER/DIM
]
button).
Display
Page 7FT-450D OPERATION MANUAL
D
ISPLAY
I
NDICATIONS
Frequency Display
The operating frequency is displayed.
: This indicator appears during transmission.
: This indicator appears whenever the receiver squelch is open.
: This indicator appears when the Internal Automatic Antenna Tuner is activated.
/ / / / / : Displays the currently selected operating mode.
/ : Displays the current CTCSS operation while in FM mode.
/ : Displays the Repeater Shift Direction while in FM mode.
: This indicator appears whenever the VOX (automatic voice-actuated transmitter switching)
circuit is activated.
: This indicator appears while the voice recorder is recording the receiver audio. This indicator
blinks while the voice recorder is playing back the recorded audio.
: This indicator appears whenever the internal CW keyer is activated.
: This indicator appears whenever the CW break-in operation is activated.
: This indicator appears when the
[
MAIN DIAL
]
knob’s tuning rate is set to fast.
: This indicator appears when the
[
MAIN DIAL
]
knob is locked.
: This indicator appears whenever the Menu Mode is engaged.
: This indicator appears whenever the Clarifier function is activated.
: This indicator appears whenever Split-frequency operation is activated.
: This indicator appears when the alternate key functions of the six command buttons located on
the upper right corner of the front panel is activated.
Block Diagram Display
: Indicates the antenna status. When the antenna system became abnormality, this indicator will blink.
: Indicates the RF attenuator status (“ON” or “OFF”) selected for operation by the
[
IPO/ATT
]
button.
: Indicates that the front-end RF pre-amplifier is removed from the receiver circuit. The incoming signal
is fed direct to the first mixer.
: Indicates the 10 kHz Roofing Filter status. This is always turned on.
: Indicates the Noise Blanker status (“ON” or “OFF”).
: Indicates the AGC decay time.
Page 8 FT-450D OPERATION MANUAL
R
EAR
P
ANEL
J
ACKS
INPUT
DC 13.8V
22 A
ANT
GND
EXT
SPKR
CATLINEARTUNERDATA
DC IN Jack
This is the DC power supply
connection for the transceiver.
Use the supplied DC cable to
connect directly to the car bat-
tery or to a DC power supply,
which must be capable of sup-
plying at least 22 A @13.8
VDC.
ANT Jack
Connect your antenna here, using a type-M (PL-259) co-
axial connector and 50 Ohm coaxial feedline.
Warning!: High Power RF voltage is present at the TX RF
section of the transceiver while transmitting. Absolutely!
Do not touch the TX RF section while transmitting.
DATA Jack
This 6-pin input/output jack provides receiver audio and squelch sig-
nals, and accepts transmit (AFSK) audio and PTT control, from an
external packet TNC.
LINEAR Jack
This 10-pin output jack pro-
vides band selection data,
which may be used for control
of the optional VL-1000 Solid-
State Linear Amplifier.
CAT Jack
This 9-pin serial DB-9 jack allows ex-
ternal computer control of the FT-
450D. Connect a (straight) serial
cable here and to the RS-232C COM
port on your personal computer (no
external interface is required).
EXT SPKR Jack
This 3.5-mm, 2-pin jack provides variable audio output for an external
speaker. The audio output impedance at this jack is 4 - 16 Ohms and
the level varies according to the setting of the front panel’s
[
AF GAIN
]
knob. Inserting a plug into this jack disables the internal loudspeaker.
GND Terminal
For safety and optimum performance, use this termi-
nal to connect the transceiver to a good earth ground.
Use a large diameter, short braided cable for making
ground connections. Refer to page 12 for other notes
about proper grounding.
SQL OUT
FSK IN
GNDDATA IN
DATA PTT
DATA OUT
TXD
TX GND OUT+13.8V OUT
GND
TUNER SENSE
TX INH IN
RXD
RESET OUT
BAND DATA-A (LSB)
TX GND OUT
+13.8V OUT
TXREG IN
GND
BAND DATA-B
BAND DATA-C
BAND DATA-D (MSB)
TX INH IN
EXT ALC IN
CTS RTS
GND
SERIAL IN
SERIAL OUT
Connect to
Connect to
N/A
Connect to
TUNER Jack
This 8-pin jack is used for Connection to
the FC-40 External Automatic Antenna
Tuner.
COOLING FAN
Turns at low speed in receive mode.
Turns at high speed when the temperature begins to
rise or in transmit mode.
(viewed from rear panel)
(viewed from rear panel)
(viewed from rear panel)
(viewed from rear panel)
(viewed from rear panel)
+
-
Page 9FT-450D OPERATION MANUAL
DYNA MIC MICROPH ONE
MH-31
DWN FST UP
S
UPPLIED
MH-31A8J M
ICROPHONE
PTT Switch
Press this Switch to transmit,
and release it to receive after
your transmission is com-
pleted.
MIC
The microphone is located
here. Speak into the micro-
phone in a normal voice level.
The microphone should be po-
sitioned within 2 inches (5 cm)
from the mouth for optimum
performance.
TONE Switch
Position 1 provides flat-audio-
characteristic transmit audio.
Position 2 attenuates low au-
dio tones, for improved clarity
in moderate band conditions,
or if you have a naturally deep
voice.
DWN Key
Press to tune down, hold to
start scanning.
UP Key
Press to tune up, hold to start
scanning.
FST
(
FAST
)
Key
The FST Button on the trans-
ceiver should be set for mo-
mentary operation.
Page 10 FT-450D OPERATION MANUAL
A
CCESSORIES
& O
PTIONS
SUPPLIED ACCESSORIES
Hand Microphone (MH-31A8J) 1 pc P/N: M3090086A
DC Power Cord with Fuse 1 pc P/N: T9025225
Fuse 1 pc P/N: Q0000074
Operation Manual 1 pc
Warranty Card 1 pc
AVAILABLE OPTIONS
External Automatic Antenna Tuner (for Wire Antenna) FC-40
Active-Tuning Antenna System ATAS-25
Active-Tuning Antenna System ATAS-120A
Solid-State Linear Amplifier/AC Power Supply VL-1000 / VP-1000
Band Data Cable (for VL-1000) CT-118
Desktop Microphone MD-100
DTMF Hand Microphone MH-36E8J
Hand Microphone MH-31A8J
Lightweight Stereo Headphone YH-77STA
Mobile Mounting Bracket MMB-90
Carrying Handle MHG-1
CT Cable (MDIN10P - Bare Wire 2m) Linear Amplifier Connection Cable (P/N T9207451)
Page 11FT-450D OPERATION MANUAL
I
NSTALLATION
CONNECTION OF ANTENNA AND POWER SUPPLY
The FT-450D is designed for use with any antenna system providing a 50 Ohm resistive impedance at the
desired operating frequency. Every effort should be made to ensure the impedance of the antenna system is as
close as possible to the specified 50-Ohm value. Note that the “G5RV” type antenna does not provide 50-Ohm
impedance on all HF Amateur bands, and an external wide-range antenna coupler must be used with this
antenna type.
Any antenna to be used with the FT-450D must, ultimately, be fed with 50 Ohm coaxial cable. Therefore, when
using a “balanced” antenna such as a dipole, remember that a balun or other matching/balancing device must
be used to ensure proper antenna performance.
AC Power Supply
FT-450D
CAUTION
Permanent damage can result if improper supply
voltage, or reverse-polarity voltage, is applied to
the FT-450D. The Limited Warranty on this trans-
ceiver does not cover damage caused by applica-
tion of AC voltage, reversed polarity DC, or DC volt-
age outside the specified range of 13.8V ±10%.
When replacing fuses, be certain to use a fuse of
the proper rating. The FT-450D requires a 25A fast-
blow fuse.
INPUT
DC 13.8 V
22 A
ANT
GND
EXT
SPKR
CATLINEARTUNERDATA
A
0 5 20 30 40
POWER
ON
OFF
RED BLACK
FUSE: 25A
V
0 5 10 15 20
Warning!
The 100V RF voltage (@100 W/50
) is applied to the TX RF section
of the transciver while transmitting.
Do not touch the TX RF section ab-
solutely while transmitting.
CAUTION
Do not position this apparatus in a location with direct exposure to sunshine.
Do not position this apparatus in a location exposed to dust and/or high humidity.
Do not expose the apparatus to dripping or splashing. Do not put objects with liquids on the apparatus.
Ensure adequate ventilation around this apparatus, so as to prevent heat build-up and possible reduc-
tion of performance due to high heat.
Do not install this apparatus in a mechanically-unstable location, or where objects may fall onto this
product from above.
To minimize the possibility of interference to home entertainment devices, take all precautionary steps
including separation of TV/FM antennas from Amateur transmitting antennas to the greatest extent
possible, and keep transmitting coaxial cables separated from cables connected to home entertain-
ment devices.
Be absolutely certain to install your transmitting antenna(s) such that they cannot possibly come in
contact with TV/FM radio or other antennas, nor with outside power or telephone lines.
Page 12 FT-450D OPERATION MANUAL
I
NSTALLATION
ABOUT COAXIAL CABLE
Use high-quality 50-Ohm coaxial cable for the lead-in to your FT-450D transceiver. All efforts at providing an
efficient antenna system will be wasted if poor quality, lossy coaxial cable is used. This transceiver utilizes
standard “M” (“PL-259”) type connector.
GROUNDING
The FT-450D transceiver, like any other HF communications apparatus, requires an effective ground system for
maximum electrical safety and best communications effectiveness. A good ground system can contribute to
station efficiency in a number of ways:
It can minimize the possibility of electrical shock to the operator.
It can minimize RF currents flowing on the shield of the coaxial cable and the chassis of the transceiver.
Such currents may lead to radiation, which can cause interference to home entertainment devices or
laboratory test equipment.
It can minimize the possibility of erratic transceiver/accessory operation caused by RF feedback and/or
improper current flow through logic devices.
An effective earth ground system may take several forms. For a more complete discussion, see an appropriate
RF engineering text. The information below is intended only as a guideline.
Typically, the ground connection consists of one or more copper-clad steel rods, driven into the ground. If
multiple ground rods are used, they should be positioned in a “V” configuration, and bonded together at the apex
of the “V” which is nearest the station location. Use a heavy, braided cable (such as the discarded shield from
type RG-213 coaxial cable) and strong cable clamps to secure the braided cable(s) to the ground rods. Be sure
to weatherproof the connections to ensure many years of reliable service. Use the same type of heavy, braided
cable for the connections to the station ground bus (described below).
Inside of the station, a common ground bus consisting of a copper pipe of at least 25 mm (1”) diameter should
be used. An alternative station ground bus may consist of a wide copper plate (single-sided circuit board material
is ideal) secured to the bottom of the operating desk. Grounding connections from individual devices such as
transceivers, power supplies, and data communications devices (TNCs, etc.) should be made directly to the
ground bus using a heavy, braided cable.
Do not make ground connections from one electrical device to an-
other, and thence to the ground bus. This so-called “Daisy-Chain”
grounding technique may nullify any attempt at effective radio fre-
quency grounding. See the drawing at the right for examples of proper
grounding techniques.
Inspect the ground system - inside the station as well as outside - on
a regular basis so as to ensure maximum performance and safety.
Besides following the above guidelines carefully, note that house-
hold or industrial gas lines must never be used in an attempt to
establish an electrical ground. Cold water pipes may, in some in-
stances, help in the grounding effort, but gas lines represent a sig-
nificant explosion hazard, and must never be used.
TYPICAL PL-259 INSTALLATION
Linear
Amplifi e r
TNC
Transceiver
Linear
Amplifi e r
TNC
Transceiver
"Daisy Chain"
PROPER GROUND CONNECTION
IMPROPER GROUND CONNECTION
1/16''
3/4''
1 1/8''
3/4''
Adapter
1/8' '
5/8''3/8''
20 mm
20 mm
30 mm
3 mm
10 mm
15 mm
2 mm
Page 13FT-450D OPERATION MANUAL
INPUT
DC 13.8V
22A
ANT
GND
EXT
SPKR
CATLINEARTUNERDATA
ANT 1
ANT 2
ANT 3
ANT 4
REMOTE
ON
OFF
BAND DATA 1
BAND DATA 2
GND
ALC 2
ALC 1
PTT 2
PTT 1
INPUT 1
INPUT 2
CONTROL
DC48V IN
A
N
T
I
N
P
U
T
D
C
1
3
.
8
V
A
N
T
1
H
F
V
e
r
t
i
c
a
l
A
n
t
e
n
n
a
H
F
D
i
p
o
l
e
A
n
t
e
n
n
a
H
F
B
e
a
m
A
n
t
e
n
n
a
A
N
T
2
A
N
T
3
I
N
P
U
T
2
L
I
N
E
A
R
B
A
N
D
-
D
A
T
A
2
G
N
D
G
N
D
D
C
4
8
V
I
N
C
O
N
T
R
O
L
A
L
C
2
CT-118 CONNECTION CABLE
(Option)
ANTENNA CABLE
(
Not Supplied
)
V
P
-
1
0
0
0
V
P
-
1
0
0
0
I
NSTALLATION
VL-1000 LINEAR AMPLIFIER INTERCONNECTION
INTERFACING TO OTHER LINEAR AMPLIFIER
Be sure that both the FT-450D and VL-1000 are turned off, then follow the installation recommendations con-
tained in the illustration.
The T/R control line is a transistor “open collector” circuit, capable of handling positive amplifier relay coil volt-
ages of up to +50V DC and current of up to 400 mA. If you plan on using multiple linear amplifiers for different
bands, you must provide external band-switching of the “Lin Tx” relay control line from the “TX GND OUT” line
at the LINEAR jack.
Important Note!
Do not exceed the maximum volt-
age or current ratings for the “TX
GND OUT” line at the LINEAR jack.
This line is not compatible with
negative DC voltages, nor AC volt-
ages of any magnitude.
Most amplifier control relay systems
require only low DC voltage/current
switching capability (typically, +12V
DC at 25 ~ 75 mA), and the switch-
ing transistor in the FT-450D will eas-
ily accommodate such amplifiers.
To link the FT-450D and VL-1000
Power switches, set the VL-1000 RE-
MOTE switch to the “ON” position.
Set the front panel’s
INPUT switch to the
“INPUT2”.
Note
Ì Please refer to the
VL-1000 Operating
Manual for details re-
garding amplifier op-
eration.
Ì Please do not at-
tempt to connect or
disconnect coaxial
cables when your
hands are wet.
EERYALC
ACFUSEGND
RF INRF OUT
A
N
T
1
A
N
T
1
H
F
A
n
t
e
n
n
a
I
N
P
U
T
1
G
N
D
G
N
D
INPUT
DC 13.8V
22A
ANT
GND
EXT
SPKR
CATLINEARTUNERDATA
I
N
P
U
T
D
C
1
3
.
8
V
L
I
N
E
A
R
L
i
g
h
t
-
B
l
u
e
B
l
a
c
k
G
r
e
e
n
Y
e
l
l
o
w
Linear Amplifier Connection Cable (T9207451: Option)
Wire Color
Orange
Yellow
Green
Red
White
Blue
Violet
Brown
Black
Gray
Light Blue
LINEA Jack
(
Pin Number
)
1
2
3
4
5
6
7
8
9
10
Case
Function
+13.8 V
TX GND OUT
GND
BAND DATA A
BAND DATA B
BAND DATA C
BAND DATA D
TX INH
EXT ALC IN
TX REQ IN
Shield
Linear Amplifier Connection Cable
(
T9207451
)
Color Code Information
Page 14 FT-450D OPERATION MANUAL
PHONES
KEY
EASY OPERATION
RECEIVING
1. Connect your antenna to the ANT jack on the rear
panel.
2. Connect the after-market DC power supply (or car
battery) using the supplied DC power cable, and set
the POWER switch of the DC power supply to on.
3. Press and hold in the
[
POWER
(
ON/OFF
)]
switch
for one second to turn the transceiver on.
4. Rotate the
[
SQL/RF GAIN
]
knob to the fully
counter-clockwise position.
5. Rotate the
[
AF GAIN
]
knob to set a comfortable
audio level on incoming signals or noise. Clock-
wise rotation of the
[
AF GAIN
]
knob increases
the volume level.
6. Press the
[
BAND
]
/
[
BAND
]
button to select the
amateur band which you wish to begin operating.
7. Press the
[
MODE
]
/
[
MODE
]
button to select
the desired operating mode.
8. Rotate the
[
MAIN DIAL
]
knob to set the desired
frequency.
[
SQL/RF GAIN
]
knob
[
AF GAIN
]
knob
[
MAIN DIAL
]
knob
[
BAND
]
/
[
BAND
]
button
[
MODE
]
/
[
MODE
]
button
TRANSMIT
1. Connect the supplied MH-31A8J to the MIC jack
on the front panel.
2. To transmit, press the microphone’s PTT (Push
To Talk) switch, speak into the microphone in a
normal voice level.
3. Release the PTT switch to return to the receive
mode.
[
POWER
(
ON/OFF
)]
switch
NOTICE
Regarding of the
[
DSP/SEL
]
knob
The
[
DSP/SEL
]
knob is used for operating
various functions depending on the situation.
If you can not change the frequency/memory
channel by tuning the
[
DSP/SEL
]
knob, the
[
DSP/SEL
]
knob is selected to operate of one
of the DSP functions.
In this case, press the
[
DSP
]
button several
times until the “>” icon disappears from the
DSP Graphic Display.
Page 15FT-450D OPERATION MANUAL
[
F
]
button
[
DSP/SEL
]
knob
HOW TO USE THE
[
DSP/SEL
]
KNOB
EASY OPERATION
When a DSP function is not selected and no “>” icon
is shown in the LCD Graphic Display, then turning
the
[
DSP/SEL
]
knob controls the frequency in VFO
mode, or selects the memory channel in memory
mode, or selects the menu item in memory mode. In
the VFO Mode, briefly depressing the
[
DSP/SEL
]
knob will permit frequency adjustment in 100 kHz
steps (Default setting). (The 100 kHz operation may
be changed with the“SELDIAL” menu function.)
When a DSP function is selected, the “>” icon will
appear next to the function in the LCD Graphic Dis-
play. Then pressing the
[
DSP/SEL
]
knob will switch
the DSP function on or off. When the DSP function is
on, turning the
[
DSP/SEL
]
knob will change the func-
tion parameters.
AD VICE:
You may change the function of the
[
DSP/SEL
]
knob
via menu item “SELDIAL”.
MENU OPERATION
The Menu System allows you to customize a wide variety of transceiver performance aspects and operating
characteristics. After you have initially customized the various Menu procedures, you will find that you will not
have to resort to them frequently during everyday operation.
1. Press and hold the
[
F
]
button for one second to
enter the Menu Mode. The “ ” icon will ap-
pear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select the Menu
Item to be adjusted.
3. Press the
[
DSP/SEL
]
knob to enable adjustment of
the selected Menu Item. The “ ” icon will blink.
4. Rotate the
[
DSP/SEL
]
knob to adjust or select
the parameter to be changed.
5. Press the
[
DSP/SEL
]
knob to save the selection.
The icon appears continuously.
6. Press and hold the
[
F
]
button for one second to
return to normal operation.
Menu Item or Menu Setting
[
DSP/SEL
]
knob
Page 16 FT-450D OPERATION MANUAL
HOW TO USE THE
[
C.S/VOICE
]
SWITCH
You may set the
[
C.S/VOICE
]
button function to one of 52 functions via Menu Item “PNL-C.S”.
To assign a function to the [C.S/VOICE] button:
1. Press and hold the
[
F
]
button for one second to enter the
Menu Mode. The “ ” icon will appear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select Menu Item “PNL-C.S”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment of
this Menu Item. The “ ” icon will be blinking.
4. Rotate the
[
DSP/SEL
]
knob to select the desired function.
5. Press the
[
DSP/SEL
]
knob. The “ ” icon returns
to appear continuously.
6. Press and hold the
[
F
]
button for one second to return
to normal operation.
EASY OPERATION
Item Function
MONI Activates the Monitor function.
N/A No Function.
P/B Activates the Digital Voice Recorder.
PLAY1 Send the CW message, which is memorized in BEACON TEXT 1.
PLAY2 Send the CW message, which is memorized in BEACON TEXT 2.
PLAY3 Send the CW message, which is memorized in BEACON TEXT 3.
QSPL Activates Quick Split Operation
SPOT Generates a CW Spot Tone while pressing the
[
C.S/VOICE
]
button when using CW mode.
SQLOFF Opens the noise squelch while pressing the
[
C.S/VOICE
]
button.
SWR Transmits a 10 watts carrier (CW mode) to measure the SWR ratio while pressing the
[
C.S/VOICE
]
button.
TXW Monitor the transmit frequency while pressing the
[
C.S/VOICE
]
button when Split Frequency operation is engaged.
VCC Display the DC supply voltage while pressing the
[
C.S/VOICE
]
button.
VOICE2 Announces the current S-meter reading, operating frequency (with resolution to the displayed 100 Hz digit), and
operating mode.
VM1MONI Play back the voice message, which is memorized in Voice Memory 1.
VM1REC Store the voice message into Voice Memory 1.
VM1TX Send the voice message, which is memorized in Voice Memory 1.
VM2MONI Play back the voice message, which is memorized in Voice Memory 2.
VM2REC Store the voice message into Voice Memory 2.
VM2TX Send the voice message, which is memorized in Voice Memory 2.
DOWN Decreases the VFO frequency by one step or moves the memory channel to the next-lowest channel while pressing
the
[
C.S/VOICE
]
button.
FAST Set to the same function as the front panel’s
[
FAST
]
button.
UP Increases the VFO frequency by one step or moves the memory channel to the next-highest channel while pressing
the
[
C.S/VOICE
]
button
DSP Set to the same function as the front panel’s
[
DSP
]
button.
IPO/ATT Set to the same function as the front panel’s
[
IPO/ATT
]
button.
NB Set to the same function as the front panel’s
[
NB
]
button.
AGC Set to the same function as the front panel’s
[
AGC
]
button.
MODEDN Set to the same function as the front panel’s
[
MODE
]
button.
MODEUP Set to the same function as the front panel’s
[
MODE
]
button.
DSP/SEL Set to the same function as the front panel’s
[
DSP/SEL
]
button.
KEYER Set to the same function as the front panel’s
[
KEYER
]
button.
CLAR Set to the same function as the front panel’s
[
CLAR
]
button.
BANDDN Set to the same function as the front panel’s
[
BAND
]
button.
BANDUP Set to the same function as the front panel’s
[
BAND
]
button.
A=B Set to the same function as the front panel’s
[
A=B
]
button.
A/B Set to the same function as the front panel’s
[
A/B
]
button.
LOCK Set to the same function as the front panel’s
[
LOCK
]
button.
TUNE Set to the same function as the front panel’s
[
TUNE
]
button.
VOICE Announce the current operating frequency
(
with resolution to the displayed 100 Hz digit
)
and operating mode.
MW Copies the current operating data from the VFO into the currently selected memory channel.
V/M Toggles frequency control between VFO and memory system.
HOME Recall the “Home”
(
favorite frequency
)
channel.
RCL Recall the QMB
(
Quick Memory Bank
)
memory.
VOX Activate the VOX
(
automatic voice-actuated transmitter switching
)
feature.
STO Copies operating data into QMB
(
Quick Memory Bank
)
Memory.
STEP Enables the setting of the frequency step of the
[
DSP/SEL
]
knob by the
[
DSP/SEL
]
knob.
SPLIT Activates split frequency operation between VFO-A and VFO-B.
PMS Engages Programmable Memory Scan
(
PMS
)
.
SCAN Initiates the upward scanning of VFO frequencies or memory channels.
MENU Engage the “Menu” mode.
DIMMER Enables adjustment of the display dimmer level by the
[
DSP/SEL
]
knob.
MTR Change the meter function in the transmit mode.
USER This parameter is for future expansion of the transceiver’s capabilities. Do not select this parameter.
[
C.S/VOICE
]
button
[
F
]
button
[
DSP/SEL
]
knob
Page 17FT-450D OPERATION MANUAL
KEY DURATION SETTING
The duration that buttons are held determines the function they activate. Factory default is one second. Pressing
a button for less than one second activates one function. Pressing and holding the button in for longer than one
second activates another function.
The default one second release time can be changed to a shorter or longer duration, if desired.
EASY OPERATION
To do this:
1. Press and hold the
[
F
]
button for one second to
enter the Menu mode again. The “ ” icon
will appear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select menu item
KEYHOLD”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment of
this menu item. The “ ” icon will be blinking.
4. Rotate the
[
DSP/SEL
]
knob to set the desired du-
ration time. Available selections are 0.5/1.0/1.5/
2.0 sec. (default value: 1.0 sec).
You may Press the
[
RCL/HOME
]
button to reset
the duration time to the factory default.
5. Press the
[
DSP/SEL
]
knob. The “ ” icon re-
turns to appear continuously.
6. Press and hold the
[
F
]
button for one second to save
the new setting and return to normal operation.
[
RCL/HOME
]
button
[
F
]
button
[
DSP/SEL
]
knob
Page 18 FT-450D OPERATION MANUAL
RESETTING THE MICROPROCESSOR
The FT-450D has three reset methods.
EASY OPERATION
VFO/MEMORY RESET
Use this procedure to reset (clear out) the Memory
channels (Except the QMB channel) previously stored
and VFO data, without affecting any configuration
changes you may have made to the Menu settings.
1. Press and hold in the
[
POWER
(
ON/OFF
)]
button
for one second to turn the transceiver off.
2. Press and hold the
[(
V/M
)
/MW
]
button. While
holding it in, press and hold in the
[
POWER
(
ON/
OFF
)]
switch for one second to turn the trans-
ceiver on. Once the transceiver comes on, you
may release the
[(
V/M
)
/MW
]
button.
[(
V/M
)
/MW
]
button
[
ON/OFF
]
button
[
F
]
button
[
ON/OFF
]
button
[
RCL/HOME
]
button
[
ON/OFF
]
button
MENU MODE RESET
Use this procedure to restore the Menu settings to
their factory defaults, without affecting the memories
you have programmed.
1. Press and hold in the
[
POWER
(
ON/OFF
)]
button
for one second to turn the transceiver off.
2. Press and hold the
[
F
]
button. While holding it in,
press and hold in the
[
POWER
(
ON/OFF
)]
button
for one second to turn the transceiver on. Once
the transceiver comes on, you may release the
[
F
]
button.
FULL RESET
Use this procedure to restore all Menu and Memory
settings to their original factory defaults. All Memo-
ries will be cleared by this procedure.
1. Press and hold in the
[
POWER
(
ON/OFF
)]
button
for one second to turn the transceiver off.
2. Press and hold the
[
RCL/HOME
]
button. While
holding it in, press and hold in the
[
POWER
(
ON/
OFF
)]
button for one second to turn the trans-
ceiver on. Once the transceiver comes on, you
may release the
[
RCL/HOME
]
button.
Page 19FT-450D OPERATION MANUAL
TUNING STEPS
RECEIVING
The tuning step of the
[
MAIN DIAL
]
knob and the
[
DSP/SEL
]
knob is different depending on the oper-
ating mode.
1: When you press the
[
DSP/SEL
]
knob, the tuning step of the
[
DSP/SEL
]
knob changes to 100 kHz in all modes.
2: In the factory default, the
[
MAIN DIAL
]
knob does not tune
the AM and FM modes. However, you may activate the
[
MAIN
DIAL
]
knob on the AM and FM mode via Menu Item
A&FDIAL”.
O
PERATING
M
ODE
LSB/USB
CW
AM
FM
DATA
[
MAIN DIAL
]
1/10/20 Hz
1/10/20 Hz
100/200 Hz
2
100/200 Hz
2
1/10/20 Hz
[
DSP/SEL
]
1
1.0/2.5/5.0 kHz
1.0/2.5/5.0 kHz
2.5/5.0/9.0/10/12.5/25 kHz
5.0/6.25/10/12.5/15/20/25/50 kHz
1.0/2.5/5.0 kHz
K
NOB
Pressing the
[
FAST
]
button will increase or de-
crease the tuning rate of the
[
MAIN DIAL
]
knob
by a factor of ten and also increase or decrease
the tuning rate of the
[
DSP/SEL
]
knob by a factor
of two.
CHANGE THE TUNING STEP OF THE
[
MAIN DIAL
]
KNOB
1. Set the operating mode by pressing the
[
MODE
]
/
[
MODE
]
button.
2. Press and hold the
[
F
]
button for one second to
enter the Menu mode. The “ ” icon will ap-
pear on the display.
3. Rotate the
[
DSP/SEL
]
knob to select the menu
item “DIALSTP”.
4. Press the
[
DSP/SEL
]
knob to enable adjustment
of this menu item. The “ ” icon will be blink-
ing.
5. Rotate the
[
DSP/SEL
]
knob to select the desired
tuning step described above.
(You may Press the
[
RCL/HOME
]
button to reset
the tuning step to the factory default.)
6. Press the
[
DSP/SEL
]
knob. The “ ” icon is
displayed continuously.
7. Press and hold the
[
F
]
button for one second to save
the new setting and return to normal operation.
CHANGE THE TUNING STEP OF THE
[
DSP/SEL
]
KNOB
1. Set the operating mode by pressing the
[
MODE
]
/
[
MODE
]
button.
2. Press the
[
F
]
button momentarily.
3. Press the
[
SPLIT/STEP
]
button.
4. Rotate the
[
DSP/SEL
]
knob to select the desired
tuning step described above.
5. Press the
[
DSP/SEL
]
knob to save the new set-
ting and return to normal operation.
[
RCL/HOME
]
button
[
F
]
button
[
DSP/SEL
]
button
[
MODE
]
/
[
MODE
]
button
[
SPLIT/STEP
]
button
[
F
]
button
[
DSP/SEL
]
knob
[
MODE
]
/
[
MODE
]
button
[
DSP/SEL
]
knob
[
MAIN DIAL
]
knob
[
FAST
]
button
NOTICE
Regarding of the
[
DSP/SEL
]
knob
The
[
DSP/SEL
]
knob is used for operating
various functions depending on the situation.
If you can not change the frequency/memory
channel by tuning the
[
DSP/SEL
]
knob, the
[
DSP/SEL
]
knob is selected to operate of one
of the DSP functions.
In this case, press the
[
DSP
]
button several
times until the “>” icon disappears from the
DSP Graphic Display.
Page 20 FT-450D OPERATION MANUAL
RECEIVING
A
BOUT
THE
[
UP
]
/
[
DWN
]
BUTTONS
OF
THE
MH-31
A8J
The microphone
[
UP
]
/
[
DWN
]
keys utilize the tun-
ing steps of the
[
MAIN DIAL
]
knob on the SSB/
CW/DATA mode, and utilize the tuning steps of
the
[
DSP/SEL
]
knob on the AM/FM mode.
When the microphone
[
FST
]
key is pressed, the
tuning rate increases by a factor of ten, in a man-
ner similar to the effect of the transceiver front-
panel
[
FAST
]
button.
CLARIFIER
You may change the receiving frequency only without changing the transmit frequency.
1. Press the
[
CLAR
]
button to activate the clarifier.
The “ ” icon will appear on the display.
2. Rotate the
[
MAIN DIAL
]
knob to tune the desired
receive frequency. (Offset of up to ±9.99 kHz may
be set using the clarifier.)
The offset frequency will appear
at the bottom right corner of the
display.
3. Press the
[
CLAR
]
button again to disable the clari-
fier. The ” icon will disappear from the dis-
play.
[
MAIN DIAL
]
knob
[
CLAR
]
button
Clarifier Offset
When the receiving frequency is
higher than transmit frequency,
“+” will be appended to the off-
set frequency.
When the receiving frequency is
lower than transmit frequency, “–”
will be appended to the offset fre-
quency.
You may assign the CLAR function to the
[
DSP/
SEL
]
knob via the Menu Item “CLAR”.
NOTE:
Even when the clarifier is disabled, the variance
of the clarifier remains (both TX and RX frequen-
cies).
Press and hold in the
[
CLAR
]
button for one sec-
ond to clear the clarifier offset, meaning the re-
ceiving frequency is equal to the transmit fre-
quency.
When the
[
MAIN DIAL
]
knob is rotated to change
the frequency after disabling the clarifier, the clari-
fier offset becomes “zero”, meaning the receiv-
ing frequency is equal to the transmit frequency.
DYNAMIC MICROPHONE
MH-31
DWN FST UP
[
DWN
]
Key
[
FST
]
Key
[
UP
]
Key
Page 21FT-450D OPERATION MANUAL
RECEIVING
DIGITAL VOICE ANNOUNCEMENT
Press the
[
F
]
button followed by the
[
C.S/VOICE
]
but-
ton to announce the current operating frequency (with
resolution to the displayed 100 Hz digit) and operat-
ing mode.
AD VICE:
If you assign the “VOICE2” function to the
[
C.S/VOICE
]
button via the menu item “PNL-C.S”, you may confirm
the current operating frequency (with resolution to the
displayed 100 Hz digit), operating mode, and S-meter
reading through the voice message announcement
system by pressing the
[
C.S/VOICE
]
button. See page
16 for details of the
[
C.S/VOICE
]
button assignment.
[
C.S/VOICE
]
button
[
F
]
button
DIAL LOCK
Pressing the
[
LOCK
]
button toggles the locking of
the [MAIN DIAL] knob and some switches, to pre-
vent accidental frequency changes.
AD VICE:
You may select the locking schemes via the menu
item “LOCKMOD”. See page 83 for details.
[
LOCK
]
button
Page 22 FT-450D OPERATION MANUAL
MY BANDS OPERATION
The “My Bands” feature allows you to select several Amateur bands, and make only those bands available for
selection via the
[
BAND
]
/
[
BAND
]
buttons.
This feature can be very useful in a contest, where the 10/18/24 MHz band are not used, or if you do not have
antennas for some bands.
MY BANDS SETUP
1. Press and hold the
[
F
]
button for one second to
enter the Menu mode again. The “ ” icon
will appear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select the menu
item “MY BAND”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment of
this menu item. The “ ” icon will be blinking.
4. Press the
[
BAND
]
/
[
BAND
]
buttons to choose
a band you wish to skip (omit) from the band se-
lection loop.
5. Rotate the
[
DSP/SEL
]
knob to select “OFF”, and
then press the
[
DSP/SEL
]
knob.
NOTE
The “OFF” selection sets the selected band to be
skipped, while the “ON” selection sets the selected
band to be included in the band-selection list.
6. Press the
[
DSP/SEL
]
knob. The “ ” icon re-
turns to appear continuously.
7. Repeat steps 4 through 6 to select/deselect as
many bands as you like.
NOTE
The GEN (General Band) and the current band
cannot be skipped.
8. Press and hold the
[
F
]
button for one second to save
the new setting and return to normal operation.
MY BANDS OPERATION
Press the
[
BAND
]
/
[
BAND
]
buttons to choose the
Amateur band on which you wish to operate. Only
those Amateur bands that have not been skipped will
appear as you scroll through the bands.
NOTE
If you want to recall an operating band which has
been set to my band “OFF”, Press the [F] button,
then press the
[
BAND
]
/
[
BAND
]
button until
the desired band appears.
RECEIVING
[
BAND
]
/
[
BAND
]
button
[
F
]
button
[
DSP/SEL
]
knob
[
BAND
]
/
[
BAND
]
button
1.8MHz
3.5
7
10
14
18
21
24
28
50
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
GEN
3.5
7
14
21
28
MHz
MHz
MHz
MHz
MHz
GEN
«
3.5MHz
7MHz 14MHz
28MHz
21MHz GEN
Page 23FT-450D OPERATION MANUAL
MY MODES OPERATION
The “My Modes” feature allows you to select the operating modes you wish to have available for selection via the
[
MODE
]
/
[
MODE
]
buttons. Only the desired modes will be displayed in the loop.
This feature can be very useful in an HF operation, where the AM/FM/DATA modes are not used.
RECEIVING
MY MODES SETUP
1. Press and hold the
[
F
]
button for one second to
enter the Menu mode again. The “ ” icon
will appear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select the menu
item “MY MODE”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment of
this menu item. The “ ” icon will be blinking.
4. Press the
[
MODE
]
/
[
MODE
]
buttons to choose
a mode you wish to skip (omit) from the mode
selection loop.
5. Rotate the
[
DSP/SEL
]
knob to select “OFF”, and
then press the
[
DSP/SEL
]
knob.
NOTE
The “OFF” selection sets the selected mode to be
skipped, while the “ON” selection sets the selected
mode to be included in the mode-selection list.
6. Press the
[
DSP/SEL
]
knob. The “ ” icon
returns to appear continuously.
7. Repeat steps 4 through 6 to select/deselect as
many modes as you like.
NOTE
The mode currently in use cannot be turned off.
8. Press and hold the
[
F
]
button for one second to save
the new setting and return to normal operation.
MY MODES OPERATION
Press the
[
MODE
]
/
[
MODE
]
buttons to choose the
operating mode on which you wish to operate. Only
those operating modes that have not been skipped
will appear as you scroll through the modes.
NOTE
If you want to recall an operating Mode which has
been set to my band “OFF”, Press the [F] button,
then press the
[
MODE
]
/
[
MODE
]
button until
the desired Mode appears.
[
F
]
button
[
DSP/SEL
]
knob
[
MODE
]
/
[
MODE
]
button
[
MODE
]
/
[
MODE
]
button
LSB
USB
CW
AM
FM
DATA
LSB
USB
FM
«
LSB US B FM
MODEMODE
CLARKEYER
Page 24 FT-450D OPERATION MANUAL
DIGITAL VOICE RECORDER
PREPARATIONS
1. Press and hold the
[
F
]
button for one second to
enter the Menu mode. The “ ” icon will ap-
pear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select the menu
item “PNL-C.S”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment of
this menu item. The “ ” icon will be blinking.
4. Rotate the
[
DSP/SEL
]
knob to select “P/B” to as-
sign the Play Back feature to the
[
C.S/VOICE
]
button.
5. Press the
[
DSP/SEL
]
knob. The “ ” icon re-
turns to appear continuously.
6. Press and hold the
[
F
]
button for one second to save
the new setting and return to normal operation.
RECORDING
1. Press and hold in the
[
C.S/VOICE
]
button for one
second to initiate recording. The “ ” icon will
appear in the display to confirm that recording is
in progress. The recorder will store up to 20 sec-
onds of the received audio and then halt the re-
cording. The “ ” icon will go out.
2. You may halt the recording in progress, by press-
ing and holding the
[
C.S/VOICE
]
button for one
second.
PLAYBACK
Press the [C.S/VOICE] button momentarily to begin
playback of the recorded audio. The “ ” icon will
blink in the display to confirm that playback is in
progress.
ADVICE:
You may adjust the playback level of the recording
with the
[
AF GAIN
]
knob
RECEIVING
[
F
]
button
[
DSP/SEL
]
knob
[
C.S/VOICE
]
button
[
C.S/VOICE
]
button
[
AF GAIN
]
knob
Page 25FT-450D OPERATION MANUAL
RECEIVER OPERATION
(
FRONT END BLOCK DIAGRAM
)
The FT-450D includes a wide range of special features to suppress the many types of interference that may be
encountered on the HF bands. However, real world interference conditions are constantly changing, so optimum
setting of the controls is somewhat of an art, requiring familiarity with the types of interference and the subtle
effects of some of the controls. Therefore, the following information is provided as a general guideline for typical
situations, and a starting point for your own experimentation.
The FT-450D’s interference-fighting circuitry begins in its “RF” stages, and continues throughout the entire
receiver section. FT-450D allows configuration of the features described below.
R. FLT
(
IF Roofing Filters
)
The Roofing filter, with a bandwidth of 10 kHz is pro-
vided in the 68 MHz First IF, right after the first mixer.
This filter provides narrow-band selectivity to protect
the following IF and DSP stages, for special operat-
ing circumstances.
CONTOUR Filter
(
SEE PAGE 28
)
The DSP Contour filter provides a unique capability
on the receiver, providing either nulling or peaking of
tunable segments of the receiver passband, so as to
suppress interference or excessive frequency com-
ponents on an incoming signal, or to peak those tun-
able frequency segments. The amount of nulling/
peaking, and the bandwidth over which it is applied,
are adjustable via the Menu.
IF SHIFT
(
S
EE PAGE 29
)
The passband center frequency response of the IF
DSP filtering may be adjusted using this control.
IF WIDTH
(
SEE P AGE 30
)
The width of the IF DSP filtering may be adjusted
using this control.
IF NOTCH
(
SEE PAGE 31
)
The IF Notch filter is a high-Q notch filter that can
significantly reduce, if not eliminate, an interfering
carrier.
DNR
(
D
IGITAL NOISE REDUCTION
)
(
S
EE PAGE 32
)
The DSP’s Digital Noise Reduction (DNR) feature uti-
lizes eleven different mathematical algorithms to ana-
lyze and suppress different noise profiles encountered
on the HF/50 MHz bands. Choose the selection that
provides the best noise suppression, which concur-
rently will allow the signal to rise up out of the noise.
AGC
(
SEE PAGE 27
)
The AGC system is highly adaptable to changing sig-
nal and fading characteristics, making reception pos-
sible under the most difficult conditions.
CONVENIENCE FEATURES
Page 26 FT-450D OPERATION MANUAL
NOISE BLANKER
(
INTERFERENCE REJECTION “SIGNALS WITHIN 3 KHZ
)
The FT-450D includes an effective Noise Blanker, which can significantly reduce noise caused by automotive
ignition systems.
IPO/ATT
(
ADJUST THE RECEIVING SENSITIVITY
)
You may reduce the receiving signal strength to 20 dB when extremely strong local signals or high noise de-
grade reception. You may optimize the characteristics of the receiver front-end, for best reception, depending on
the noise levels and the signal strengths.
Press the
[
IPO/ATT
]
button several times to set the
desired selection, per the chart below.
The selection will be indicated in the Block Diagram
on the display.
Block Diagram
[
IPO/ATT
]
button
CONVENIENCE FEATURES
1. Press the
[
NB
]
button to activate the Noise
Blanker.
2. Press the
[
NB
]
button again to disable the Noise
Blanker.
The selection will be indicated in the Block Diagram
on the display.
Block Diagram
[
NB
]
button
NOTE
An attenuator is always “ON” between 30kHz
and 1.7MHz.
ATT: OFF, IPO: OFF Attenuator is OFF, and the incoming
signal is amplified by the RF preampli-
fier.
ATT: OFF, IPO: ON Attenuator is OFF, and the incoming
signal bypasses the RF preamplifier,
yielding direct feed to the first mixer.
ATT: ON, IPO: OFF Attenuator is ON, (the incoming signal
is reduced by 20 dB) and the incom-
ing signal is amplified by the RF pream-
plifier.
ATT: ON, IPO: ON Attenuator is ON, (the incoming signal
power is reduced by 20 dB) and the
incoming signal bypasses the RF
preamplifier, yielding direct feed to the
first mixer.
Page 27FT-450D OPERATION MANUAL
AGC
(
TOOL FOR COMFORTABLE AND EFFECTIVE RECEPTION
)
The AGC system is designed to help compensate for fading and other propagation effects, with characteristics
that can be of particular value on each operating mode. The basic objective of AGC is to maintain a constant
audio output level once a certain minimum threshold of signal strength is achieved.
Press the
[
AGC
]
button repeatedly to select the de-
sired receiver-recovery time constant. The AGC sta-
tus is indicated in the Block Diagram displayed on
the display. For most operations, we recommend the
“AUTO” mode. You may disable the AGC by press-
ing and holding in the
[
AGC
]
button for one second.
CONVENIENCE FEATURES
Block Diagram
[
AGC
]
button
NOTE:
Normally, the “AUTO” selection is satisfactory for most
situations, but in the event of operation on a crowded
band where you wish to receive a weak signal, you
may wish to change the setting (to FAST, for ex-
ample). The “AUTO” mode selections are:
AD VICE:
If the AGC receiver-recovery time is set to “Off”
by pressing and holding in the
[
AGC
]
button,
the S-meter will no longer deflect. Additionally, you
will likely encounter distortion on stronger signals, as
the IF amplifiers and the following stages are prob-
ably being overloaded.
AUTO Sets the receiver-recovery time automatically
depending on the operating mode.
FAST Sets the receiver-recovery time to fast.
This mode is suitable for CW/DATA recep-
tion.
SLOW Sets the receiver-recovery time to slow.
This mode is suitable for SSB/AM reception.
OPERATING MODE
LSB
USB
CW
AM
FM
DATA
AUTO AGC SELECTION
SLOW
SLOW
FAST
SLOW
FAST (Fixed)
FAST
Page 28 FT-450D OPERATION MANUAL
IF
BANDWIDTH
IF
BANDWIDTH
IF
BANDWIDTH
CONTOUR
(
INTERFERENCE REJECTION “SIGNALS WITHIN 3 KHZ
)
The Contour filtering system provides a gentle perturbation of the IF filter pass band, so as to suppress or
enhance particular frequency components in five steps, thus improving the sound and/or readability of a re-
ceived signal.
1. Press the
[
DSP
]
button several times to set the
>” icon to the “CONTOUR” indicator of the DSP
Graphic Display on the display.
2. Press the
[
DSP/SEL
]
knob to engage the con-
tour filter.
3. Press and hold the
[
DSP/SEL
]
knob for one sec-
ond to toggle the contour filter’s level between
“null” and “peak”.
4. Rotate the
[
DSP/SEL
]
knob to achieve the most
natural-sounding audio reproduction on the in-
coming signal.
The peak position of the contour filter is graphi-
cally-depicted in the “CONTOUR” indicator of the
DSP Graphic Display on the LCD.
5. Press the
[
DSP/SEL
]
knob again to increase the
contour filter’s level (“null” or “peak”).
6. To disable the contour filter, press the
[
DSP/SEL
]
button again. The graphic disappears from the
CONTOUR” indicator of the LCD Display, confirm-
ing that the contour filter is no longer operating.
QUICK POINT:
The steep slopes of the DSP filtering can, when adjusted aggressively, impart an unnatural sound to an incom-
ing signal. Often, a narrow bandwidth is not the key to improving copy. The incoming signal itself may have
undesirable or excessive frequency components. By judicious use of the Contour filter, the “shoulder” of the
passband response may be altered, or components removed from within the passband, allowing the desired
signal to rise above the background noise and interference in a manner not obtainable with other filtering sys-
tems.
CONVENIENCE FEATURES
“CONTOUR” Indicator
[
DSP
]
button
[
DSP/SEL
]
knob
CONTOUR GAIN “HIGH
C
ONTOUR “NULL
CONTOUR “PEAK
C
ONTOUR “OFF
CONTOUR GAIN “LOW
C
ONTOUR “NULL
C
ONTOUR “PEAK
CONTOUR “OFF
Refer to Figure “B”, this shows a “indenta-
tion” of the contour filter is center of a pass-
band. Counter-clockwise rotation (to the left)
of the
[
DSP/SEL
]
knob causes the indenta-
tion to move toward a lower frequency within
the passband, while clockwise rotation (to the
right) causes the indentation to move toward
a higher frequency within the passband. By
removing interference or unwanted frequency
components on the incoming signal, it is pos-
sible to make the desired signal rise out of
the background noise/interference, enhanc-
ing intelligibility.
A B C
Page 29FT-450D OPERATION MANUAL
SHIFT
(
INTERFERENCE REJECTION “SIGNALS WITHIN 3 KHZ
)
IF Shift allows you to vary the DSP filter passband higher or lower, without changing the pitch of the incoming
signal, so as to reduce or eliminate interference. Because the carrier tuning frequency is not varied, there is no
need to re-tune the operating frequency when eliminating the interference. The total passband tuning range for
the IF Shift system is ±1 kHz.
CONVENIENCE FEATURES
Rotate the
[
SHIFT
]
knob to the left or right to reduce
the interference.
You may observe the position of the passband in the
SHIFT” indicator of the DSP Graphic Display on the
display.
“SHIFT” Indicator
[
SHIFT
]
knob
[
SHIFT
]
KNOB FULLY COUNTER-CLOCKWISE
[
SHIFT
]
KNOB 12 O
CLOCK POSITION
[
SHIFT
]
KNOB FULLY CLOCKWISE
Referring to Figure “A”, note the depiction of
the IF DSP filter as the thick line, with the
[
SHIFT
]
knob in the 12 o’clock position. In
Figure “B”, an interfering signal has appeared
inside the original passband. In Figure “C”,
you can see the effect of rotating the
[
SHIFT
]
knob to reduce the interference level by mov-
ing the filter passband so that the interfer-
ence is outside of the passband.
A B C
IF
BANDWIDTH
IF
BANDWIDTH
IF
BANDWIDTH
Desired Signal Desired Signal Desired Signal
QRMQRM
Page 30 FT-450D OPERATION MANUAL
Referring to Figure “B”, this is default band-
width.
By rotating the
[
DSP/SEL
]
knob to the left,
the bandwidth will narrow (see Figure “A”),
while rotation of the
[
DSP/SEL
]
knob to the
right, as depicted in Figure “C”, will widen the
bandwidth.
The default bandwidths, and total bandwidth
adjustment range, will vary according to the
operating mode:
SSB Mode: 1.8 kHz / 2.4 kHz / 3.0 kHz
(Nominal: 2.4 kHz).
CW Mode: 300 Hz / 500 Hz / 2.4 kHz
(Nominal: 2.4 kHz).
DATA Mode:300 Hz / 2.4 kHz / 3.0 kHz
(Nominal: 2.4 kHz).
AM Mode: 3.0 kHz / 6.0 kHz / 9.0 kHz
(Nominal: 6.0 kHz).
FM Mode: 2.5 kHz / 5.0 kHz
(Nominal: 5.0 kHz).
A B C
WIDTH
(
INTERFERENCE REJECTION “SIGNALS WITHIN 3 KHZ
)
The IF Width tuning system allows you to vary the width of the DSP IF passband with three steps (FM: two
steps), so as to eliminate interference. Moreover, the bandwidth may actually be expanded from its default
setting, should you wish to enhance incoming signal fidelity when interference on the band is low.
CONVENIENCE FEATURES
1. Press the
[
DSP
]
button several times to set the
>” icon to the “WIDTH” indicator of the DSP
Graphic Display on the display, to enable adjust-
ment of the bandwidth by the
[
DSP/SEL
]
knob.
2. Rotate the
[
DSP/SEL
]
knob to adjust the band-
width. Counter-clockwise rotation reduces the
bandwidth, while clockwise rotation increases the
bandwidth.
“WIDTH” Indicator
[
DSP
]
button
[
DSP/SEL
]
knob
Using IF Shift and Width Together
The IF Shift and Variable IF Width features
together form a very effective interference-
fighting filtering system.
For example, in Figure “A” you can see how
interference has appeared both on the high
and low sides of the desired signal. By rotat-
ing the
[
DSP/SEL
](
WIDTH
)
knob, as shown
in Figure “B”, the interference from one side
can be eliminated, and by re-positioning the
[
SHIFT
]
knob (Figure “C”), the interference
on the opposite side can be removed, with-
out re-introducing the interference previously
eliminated in Figure “B”.
Advice: For best interference reduction, the
Width and Shift features are the primary tools
you should use. After narrowing the bandwidth
(Width) and/or adjusting the center of the
passband (Shift), the Contour control may
also yield additional signal-enhancement ben-
efits on the net residual bandwidth. What’s
more, the IF Notch Filter (see the next sec-
tion) may also be utilized, in conjunction with
the three other filter systems, to significant
advantage.
A B C
IF
BANDWIDTH
IF
BANDWIDTH
IF
BANDWIDTH
IF
BANDWIDTH
IF
BANDWIDTH
IF
BANDWIDTH
Desired Signal Desired Signal Desired Signal
QRM
QRMQRMQRM
QRMQRM
Page 31FT-450D OPERATION MANUAL
CONVENIENCE FEATURES
NOTCH
(
INTERFERENCE REJECTION “SIGNALS WITHIN 3 KHZ
)
The IF Notch filter is a highly effective system that allows you to slice out an interfering beat note or other carrier
signal from inside the receiver passband.
“NOTCH” Indicator
[
DSP
]
button
[
DSP/SEL
]
knob
1. Press the
[
DSP
]
button several times to set the
>” icon to the “NOTCH” indicator of the DSP
Graphic Display on the display.
2. Press the
[
DSP/SEL
]
knob to engage the IF Notch
filter.
3. Rotate the
[
DSP/SEL
]
knob to adjust the center
frequency of the IF Notch Filter.
You may observe the graphically depicted peak
position of the IF Notch filter in the “NOTCH” indi-
cator of the DSP Graphic Display on the display.
4. To disable the IF Notch filter, press the
[
DSP/SEL
]
button again. The graphically depicted peak po-
sition disappears from the “NOTCH” indicator of
the DSP Graphic Display on the display confirm-
ing that the IF Notch filter is no longer operating.
The performance of the IF Notch filter is
shown in Figure “A”, where the effect of rota-
tion of the
[
DSP/SEL
]
knob is depicted. In
Figure “B”, you can see the notching effect
of the IF Notch filter as you rotate the
[
DSP/
SEL
]
knob to eliminate the incoming interfer-
ence.
A B
IF
BANDWIDTH
QRM
(Heterodyne)
QRM
(Heterodyne)
IF
BANDWIDTH
Desired Signal Desired Signal
Page 32 FT-450D OPERATION MANUAL
“DNR” Indicator
[
DSP
]
button
[
DSP/SEL
]
knob
DNR
(
INTERFERENCE REJECTION “SIGNALS WITHIN 3 KHZ
)
The Digital Noise Reduction (DNR) system is designed to reduce the level of random noise found on the HF and
50 MHz bands, and it is especially effective during SSB operation. Any of eleven different noise-reduction algo-
rithms can be selected. Each of these algorithms was created for dealing with a different noise profile, and you
will want to experiment with the DNR system to find the best setting according to the noise currently being
experienced.
1. Press the
[
DSP
]
button several times to set the
>” icon to the “DNR” indicator of the DSP Graphic
Display on the display.
2. Press the
[
DSP/SEL
]
knob to engage the Digital
Noise Reduction system.
3. Rotate the
[
DSP/SEL
]
knob to select the setting
that most effectively reduces the noise level.
You may observe the effectiveness of the Digital
Noise Reduction system in the “DNR” indicator
of the DSP Graphic Display on the display.
4. To disable the Digital Noise Reduction system,
press the
[
DSP/SEL
]
button again. The graph ef-
fectively disappears from the “DNR” indicator of
the DSP Graphic Display on the display confirm-
ing that the Digital Noise Reduction system is no
longer operating.
CONVENIENCE FEATURES
Page 33FT-450D OPERATION MANUAL
RF GAIN
The RF Gain controls provide manual adjustment of the gain levels for the receiver RF and IF stages, to com-
pensate for noise and/or signal strength conditions at the moment.
The
[
SQL/RF GAIN
]
knob should, initially, be rotated
to the fully clockwise position. This is the point of maxi-
mum sensitivity, and counter-clockwise rotation will
gradually reduce the system gain.
AD VICE:
As the
[
SQL/RF GAIN
]
knob is rotated counter-
clockwise to reduce the gain, the S-meter read-
ing will rise. This indicates that the AGC voltage
being applied to the receiver is increasing (which
causes a reduction in receiver gain).
Rotating the
[
SQL/RF GAIN
]
knob control to the
fully counter-clockwise position will essentially dis-
able the receiver, as the gain will be greatly re-
duced. In this case, the S-meter will appear to be
“pegged”. (That is a full-scale reading).
[
SQL/RF GAIN
]
knob
CONVENIENCE FEATURES
Page 34 FT-450D OPERATION MANUAL
U
SING
THE
A
UTOMATIC
A
NTENNA
T
UNER
The Automatic Antenna Tuner (hereinafter referred to as the “ATU”) built into each FT-450D is designed to
ensure a 50-Ohm load for the final amplifier stage of the transmitter. We recommend that the ATU be used
whenever you operate on the FT-450D.
ADVICE:
Because the ATU of the FT-450D is located inside the station, it only adjusts the impedance presented to the
transceiver at the station end of your coaxial cable feedline. It does not “tune” the SWR at the antenna feed
point itself. When designing and building your antenna system, we recommend that every effort be made to
ensure a low SWR at the antenna feed point.
The ATU of the FT-450D includes 100 memories for tuning data. Eleven of these memories are allocated,
one per Amateur band, so that each band has at least one setting preset for use on that band. The remaining
89 memories are reserved for the 89 most-recent tuning points, for quick frequency change without the need
to retune the ATU.
The ATU in the FT-450D is designed to match impedances within the range of 16.7 Ohms to 150 Ohms,
corresponding to an SWR of 3:1 or less on the 160 through 6 meter amateur bands. Accordingly, simple
non-resonant whip antennas, along with random-length wires and the “G5RV” antenna (on most bands) may
not be within the impedance matching range of the ATU.
ATU OPERATION
1. Use the Main Tuning Dial knob to set the radio to
the desired operating frequency within the Ama-
teur band.
2. Press the [TUNE] button momentarily to place
the ATU in the transmit line (no adjustment/tun-
ing will occur yet). The “ ” icon will appear
in the display.
QUICK POINT:
The momentary press of the [TUNE] button will
turn the tuner on, and the microprocessor will
automatically select the tuning point closest to
the current operating frequency.
3. Press and hold in the [TUNE] button for one sec-
ond to begin automatic tuning. The transmitter
will be engaged, and the “ ” icon will blink
while tuning is in progress. When the optimum
tuning point has been reached, the radio will re-
turn to receive, and the “ ” icon will again
glow steadily (instead of blinking).
4. To disconnect the ATU from the transmit line,
press the [TUNE] button momentarily. The
” icon will turn off, confirming that the ATU
has been turned off. In the “Off” mode, the trans-
ceiver will be directly connected to the coaxial
cable connected to your antenna, and will oper-
ate based on whatever impedance is present at
the station end of the coax.
ADVICE:
The ATU circuit is located between the final amplifier
and the rear-panel antenna jack; reception is not af-
fected by the ATU.
QUICK POINTS:
As shipped from the factory, only one ATU alignment
point is saved on each Amateur band. This was
memorized during the final alignment and perfor-
mance verification stages on the production line.
NOTE:
Please check the operating frequency before begin-
ning the tuning process, to be sure you are not inter-
fering with others who may already be using the fre-
quency.
TERMINOLOGY:
Antenna Tuner Memories: The microprocessor of the
ATU makes a note of the positions of the tuning ca-
pacitors and the selected inductors, and stores the
data for each 10 kHz window in which tuning has
occurred. This eliminates the need to re-tune every
time you return to a frequency on which you have
already completed the tuning process.
[
TUNE
]
button
Page 35FT-450D OPERATION MANUAL
U
SING
THE
A
UTOMATIC
A
NTENNA
T
UNER
ABOUT ATU OPERATION
Figure 1 depicts a situation where normal tuning via the ATU has been successfully completed, and the tuning
data has been stored in the ATU memory. The antenna system as seen by the transmitter is shown.
In Figure 2, the operator has changed frequency, and the “ ” icon has appeared. The operator presses and
holds in the [TUNE] button for two seconds to begin impedance matching using the ATU.
If a high SWR condition exists (above 3:1), corrective action must be taken in the antenna system to bring the
impedance closer to 50 Ohms. The ATU will refuse to memorize settings on frequencies where the SWR
exceeds 3:1. A High SWR may indicate a mechanical failure in the feed system, and can lead to the generation
of spurious signals causing TVI, etc.
About ATU Memories
SWR (After tuning) Less than 2:1
The tuner settings are stored in the ATU memory.
SWR (After tuning) Greater than 2:1
Tuning data will not be retained in memory. If you return to the same frequency, the tuning process must be
repeated.
SWR (After tuning) Greater than 3:1
The “ ” icon does not blink, and the tuner settings, if achieved, will not be memorized. Please investi-
gate the high SWR condition and resolve the problem, before attempting further operation using this an-
tenna.
SWR: 2.0
Frequency
SWR: 1.5
Feed Point SWR
SWR after ATU Tuning
SWR: 1.0
FIGURE 1
FIGURE 2
SWR = 1.0
SWR = 2.0
SWR = 3.0
©
Frequency
Memorized ATU Tuning
Retuned Setting
SWR: 3.0
The " " icon appears on the display
when you transmit on this frequency
Page 36 FT-450D OPERATION MANUAL
PHONES
KEY
1. Press the
[
BAND
]
/
[
BAND
]
buttons to select
the operating band.
By pressing the
[
BAND
]
/
[
BAND
]
buttons, the
operating band will change as follows.
7 10 14 15 18 21 24.5
28 50 1.8 3.5 7
......
2. Press the
[
MODE
]
/
[
MODE
]
buttons to select
the LSB, USB or AM mode.
By convention, LSB is used in the 7 MHz and
lower Amateur bands for SSB communication,
and USB is used on the 14 MHz and higher bands
(the 10 MHz band is used for CW and data modes
only).
3. Rotate the
[
MAIN DIAL
]
knob to adjust the oper-
ating frequency.
If you use the MH-31A8J (or MD-100A8X: option),
you may adjust the operating frequency by the
[
UP
]
/
[
DWN
]
buttons on the microphone.
SSB/AM MODE TRANSMISSION
4. Press the microphone’s PTT (Push To Talk)
switch to begin transmission. Speak into the mi-
crophone in a normal voice level.
The “ ” icon will appear in the display, con-
firming that transmission is in progress.
The Speech Processor is automatically activated
while transmitting. The Speech Processor in-
creases “talk power” by increasing the average
power output.
5. Release the PTT switch at the end of your trans-
mission. The transceiver will return to the receive
mode.
IMPORTANT NOTE:
When performing tests, be sure to check the fre-
quency before transmitting, to avoid interfering with
others who may already be using the frequency.
[
MAIN DIAL
]
knob
[
BAND
]
/
[
BAND
]
button
[
MODE
]
/
[
MODE
]
button
NOTICE
Regarding of the
[
DSP/SEL
]
knob
The
[
DSP/SEL
]
knob is used for operating
various functions depending on the situation.
If you can not change the frequency/memory
channel by tuning the
[
DSP/SEL
]
knob, the
[
DSP/SEL
]
knob is selected to operate of one
of the DSP functions.
In this case, press the
[
DSP
]
button several
times until the “>” icon disappears from the
DSP Graphic Display.
Page 37FT-450D OPERATION MANUAL
SSB/AM MODE TRANSMISSION
TX METER SELECTION
You may change the PO meter function to ALC meter or SWR meter in the transmit mode.
TX POWER ADJUSTMENT
By pressing the
[
METER/DIM
]
button, the meter func-
tion will change as follows.
PO ALC SWR PO
......
PO: Indicates the average power output level.
ALC: Indicates the relative ALC voltage.
SWR: Indicates the Standing Wave Ratio.
Adjusting the TX output power:
1. Press and hold the
[
F
]
button for one second to
enter the Menu mode. The “ ” icon will ap-
pear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select the menu
item “RFPOWER”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment
of this menu item. The “ ” icon will be blink-
ing.
4. Rotate the
[
DSP/SEL
]
knob to select the desired
power output.
You may press the
[
RCL/HOME
]
button to reset
the power output to the factory default.
5. Press the
[
DSP/SEL
]
knob. The “ ” icon re-
turns to appear continuously.
6. Press and hold the
[
F
]
button for one second to
save the new setting and return to normal opera-
tion.
[
RCL/HOME
]
button
[
F
]
button
[
DSP/SEL
]
knob
[
METER/DIM
]
button
Page 38 FT-450D OPERATION MANUAL
TRANSMITTER TIME-OUT TIMER
(
TOT
)
The “Time-Out Timer” (TOT) feature that is designed to force the transceiver into the “receive” mode after a
preset time period of continuous transmission (the default is “OFF”). This feature prevents your transceiver from
transmitting a “dead carrier” for a long period of time if the microphone PTT switch is accidentally locked in the
“TX” condition. The Time-Out Timer “switch-to-receive” time may be adjusted from 1 to 20 minutes, or Off via
Menu Item “TOT”.
1. Press and hold the
[
F
]
button for one second to
enter the Menu mode again. The “ ” icon
will appear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select the menu
item “TOT”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment
of this menu item. The “
” icon will be blink-
ing.
4. Rotate the
[
DSP/SEL
]
knob to select the desired
“Maximum TX” time. Available selections are 1
minute through 20 minutes or off.
Press the
[
RCL/HOME
]
button to reset the TOT
time to the factory default.
5. Press the
[
DSP/SEL
]
knob. The “
” icon re-
turns to appear continuously.
6. Press and hold the
[
F
]
button for one second to
save the new setting and return to normal opera-
tion.
[
RCL/HOME
]
button
[
F
]
button
[
DSP/SEL
]
knob
SSB/AM MODE TRANSMISSION
Page 39FT-450D OPERATION MANUAL
MICROPHONE GAIN LEVEL ADJUSTMENT
At the factory, a microphone gain has been programmed that should be satisfactory for the supplied MH-31A8J
Hand Microphone. If you use an after-market microphone, you may wish to set a different Microphone Gain
Level.
1. Press and hold the
[
F
]
button for one second to
enter the Menu mode again. The “ ” icon
will appear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select the menu
item “MICGAIN”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment
of this menu item. The “ ” icon will be blink-
ing.
4. Rotate the
[
DSP/SEL
]
knob to select the desired
microphone gain (LOW, NOR, or HIGH, factory
default: NOR).
LOW: When the microphone input is high the
speech processor is turned off automati-
cally.
NOR For normal voice the speech processor is
turned on automatically.
HIGH: When the microphone input is low the
speech processor is turned on automati-
cally.
Press the
[
RCL/HOME
]
button to reset the mi-
crophone gain to the factory default.
5. Press the
[
DSP/SEL
]
knob. The “ ” icon re-
turns to appear continuously.
6. Press and hold the
[
F
]
button for one second to
save the new setting and return to normal opera-
tion.
[
RCL/HOME
]
button
[
F
]
button
[
DSP/SEL
]
knob
SSB/AM MODE TRANSMISSION
Page 40 FT-450D OPERATION MANUAL
DSP MICROPHONE EQUALIZER
You may select one of ten available DSP equalization techniques for transmitted microphone audio.
1. Press and hold the
[
DSP
]
button for one second.
This instantly activates menu item “MIC EQ. The
icon will appear on the display.
2. Press the
[
DSP/SEL
]
knob to enable adjustment of
this menu item. The “ ” icon will be blinking.
3. Rotate the
[
DSP/SEL
]
knob to select the desired
equalizer pattern.
Observe the relative equalizer pattern on the dis-
play.
(You may press the
[
RCL/HOME
]
button to reset
the equalizer pattern to the factory default.)
4. Press the
[
DSP/SEL
]
knob. The “ ” icon re-
turns to appear continuously.
5. Press and hold the
[
F
]
button for one second to save
the new setting and return to normal operation.
The available selections are:
0: Flat
1: Low-frequency components are reduced.
2: Mid-frequency components are reduced.
3: High-frequency components are reduced.
4: High-frequency components are enhanced.
5: Mid-frequency components are enhanced.
6: Low-frequency components are enhanced.
7: Low-frequency components are enhanced
and High-frequency components are re-
duced.
8: Low-frequency components are reduced and
Mid-frequency components are enhanced.
9: Low-frequency components are reduced and
High-frequency components are enhanced
SSB/AM MODE TRANSMISSION
[
RCL/HOME
]
button
[
F
]
button
[
DSP/SEL
]
knob
[
DSP
]
button
Page 41FT-450D OPERATION MANUAL
AUTOMATIC TX/RX SWITCHING USING VOICE CONTROL
(
VOX
)
Instead of using the microphone’s PTT switch to activate the transmitter, the VOX (Voice Operated TX/RX
Control) system provides hands-free, automatic activation of the transmitter, based on voice input into the mi-
crophone. Setup of the VOX system takes only a few seconds.
SSB/AM MODE TRANSMISSION
1. Press the
[
F
]
button followed by the
[
STO/VOX
]
button to engage the VOX operation.
The “ ” icon will appear in the display.
2. Without pressing the PTT switch, speak into the
microphone in a normal voice level.
When you start speaking, the transmitter should
be activated automatically. When you finish
speaking, the transceiver should return to the
receive mode (after a short delay).
3. To exit from VOX operation, press the
[
F
]
button
followed by the
[
STO/VOX
]
button again.
[
RCL/HOME
]
button
[
F
]
button
[
DSP/SEL
]
knob
[
STO/VOX
]
button
[
F
]
button
VOX GAIN ADJUSTMENT
Adjust the VOX gain level to prevent accidental transmitter activation in a noisy environment.
1. Press and hold the
[
F
]
button for one second to
enter the Menu mode. The “ ” icon will ap-
pear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select the menu
item “VOXGAIN”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment of
this menu item. The “ ” icon will be blinking.
4. Rotate the
[
DSP/SEL
]
knob to set to the point
where the transmitter is quickly activated by your
voice, without causing background noise to acti-
vate the transmitter. Available selections are 1
through 100 (factory default: 50).
Press the
[
RCL/HOME
]
button to reset the VOX
gain level to the factory default.
VOX DELAY ADJUSTMENT
(
THE TRANSMIT-RECEIVE DELAY AFTER THE CESSATION OF SPEECH
)
1. Press and hold the
[
F
]
button for one second to
enter the Menu mode again. The “ ” icon
will appear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select the menu
item “VOX DLY”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment of
this menu item. The “ ” icon will be blinking.
4. Rotate the
[
DSP/SEL
]
knob while saying a brief
syllable like “Ah” and listening to the hang time,
so as to set the desired delay. Available selec-
tions are 100 through 3000 msec (factory default:
500 msec).
Press the
[
RCL/HOME
]
button to reset the VOX
delay time to the factory default.
5. Press the
[
DSP/SEL
]
knob. The “ ”” icon
returns to appear continuously.
6. Press and hold the
[
F
]
button for one second to save
the new setting and return to normal operation.
5. Press the
[
DSP/SEL
]
knob. The “ ” icon re-
turns to appear continuously.
6. Press and hold the
[
F
]
button for one second to save
the new setting and return to normal operation.
[
RCL/HOME
]
button
[
F
]
button
[
DSP/SEL
]
knob
Page 42 FT-450D OPERATION MANUAL
SSB/AM MODE TRANSMISSION
MONITOR
You may listen to the quality of your transmitted signal using the Monitor feature.
PREPARATIONS
Assign the Monitor feature to the
[
C.S/VOICE
]
button.
1. Press and hold the
[
F
]
button for one second to
enter the Menu mode. The “ ” icon will ap-
pear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select the menu
item “PNL-C.S”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment of
this menu item. The “ ” icon will be blinking.
4. Rotate the
[
DSP/SEL
]
knob to select “MONI” to
assign the Monitor feature to the
[
C.S/VOICE
]
button.
5. Press the
[
DSP/SEL
]
knob. The “ ” icon re-
turns to appear continuously.
6. Press and hold the
[
F
]
button for one second to save
the new setting and return to normal operation.
ADVICE:
You may assign the MONITOR feature to the MH-
31A8J (or optional microphone’s)
[
DWN
]
/
[
FST
]
/
[
UP
]
button via the Menu Item “P M-DWN”, “P M-FST” or “P
M-UP”.
MONITORING
1. Press the
[
C.S/VOICE
](
MONITOR
)
button to ac-
tivate the Monitor feature.
During transmission, your transmitted voice is
output from the speaker.
2. Rotate the
[
AF GAIN
]
knob to adjust the audio
level from the monitor.
3. To disable the Monitor feature, press the
[
C.S/
VOICE
](
MONITOR
)
button again.
[
F
]
button
[
DSP/SEL
]
knob
ADVICE:
If you are using the speaker for monitoring, instead of headphones, excessive advancement of the
[
AF
GAIN
]
knob can cause feedback to occur. Additionally, this feedback can cause the VOX system to hang up
in a loop, making it impossible to return to receive. Therefore, we recommend the use of headphones, if at
all possible, or the minimum usable setting of the
[
AF GAIN
]
knob, if the speaker must be used.
Because the Monitor feature utilizes a sampling of the transmitter’s DSP signal, it can be very useful for
checking the adjustment of the Speech Processor or Microphone Equalizer on SSB, and for checking the
general signal quality on AM and FM.
[
C.S/VOICE
]
button
[
AF GAIN
]
button
[
C.S/VOICE
]
button
Page 43FT-450D OPERATION MANUAL
SSB/AM MODE TRANSMISSION
SPLIT-FREQUENCY OPERATION
A powerful capability of the FT-450D is its flexibility in Split Frequency operation, using VFO-A and VFO-B
frequency registers. This makes the FT-450D especially useful for high-level DX-pedition use, as the Split op-
eration capability is very advanced and easy to use.
1. Press the
[
A/B
]
button to switch the VFO register
to VFO-B, then set the transmit frequency.
2. Press the
[
A/B
]
button again to switch the VFO
register to VFO-A, then set the receive frequency.
3. Now press the
[
SPLIT/STEP
]
button to activate
Split-Frequency Operation.
4. The “ ” icon will appear in the display.
5. To quit Split-Frequency Operation, press the
[
SPLIT/STEP
]
button again.
AD VICE:
It is possible to set different operating modes (for
example, LSB and USB) on the two VFOs used
during Split operation.
It is possible to set different amateur bands (for
example, 14 MHz and 21 MHz) on the two VFOs
used during Split operation, if you use the multi
band antenna.
QUICK SPLIT OPERATION
The Quick Split feature allows you to set a one-touch offset of +5 kHz to be applied to your radio’s
transmit frequency compared to the receiving frequency. Furthermore, the transmit mode sets to the
same mode as the receiving frequency register.
1. Press and hold in the [SPLIT/STEP] button
for one second to engage the Quick Split fea-
ture. The transmit mode is set to the same
mode as the receiver frequency register and
applies a frequency 5 kHz above the receiv-
ing frequency register to the transmit fre-
quency register.
The “ ” icon will appear in the display.
2. Press and hold in the
[
SPLIT/STEP
]
button
for one second to increment the transmit fre-
quency +5 kHz.
3. To quit the Quick Split Operation, press the
[
SPLIT/STEP
]
button again.
[
SPLIT/STEP
]
button
[
A/B
]
button
[
C.S/VOICE
]
button
[
SPLIT/STEP
]
button
ADVICE:
If you assign the “TXW” feature into the [C.S/VOICE] button, you may also listen to the TX frequency
temporarily while pressing the [C.S/VOICE] button during Split operation.
Page 44 FT-450D OPERATION MANUAL
SSB/AM MODE TRANSMISSION
VOICE MEMORY
(
SSB/AM/FM MODES
)
You may utilize the Voice Memory capability of the FT-450D for repetitive messages. The Voice Memory system
includes two memories (VM1 and VM2) capable of storing up to 10 seconds of voice audio each. The maximum
that both memories can hold is 10 seconds.
Recording Your Own Voice in Memory
1. Assign the “VM1REC” (Voice Recording) function
to the
[
C.S/VOICE
]
button using the procedure in
the box below.
2. Select the LSB, USB, AM, or FM mode using the
[
MODE
]
/
[
MODE
]
buttons.
2. Press the
[
C.S/VOICE
]
button. AVM1 REC” no-
tation will appear in the display.
3. Press and hold the microphone’s PTT switch, the
radio display will count down.
(“VM1
3” VM1
2” VM1
1” VM1 10”
......
)
5. When the display Shows “VM1 10”, speak into
the microphone in a normal voice level to record
the message (such as “CQ DX, CQ DX, this is W
6 Delta X-Ray Charlie, W 6 Delta X-Ray Charlie,
Over”). Remember that the time limit for record-
ing is 10 seconds.
6. Release the PTT switch to terminate the mes-
sage storage process.
Checking Your Recording
1. Assign the “VM1MONI” (Voice Monitoring) func-
tion to the
[
C.S/VOICE
]
button using the proce-
dure in the box below.
2. Select the LSB, USB, AM, or FM mode using the
[
MODE
]
/
[
MODE
]
buttons.
3. Press the
[
C.S/VOICE
]
button, and you will hear
the contents of the voice memory you just re-
corded.
4. You may adjust the playback level of the record-
ing by the
[
AF GAIN
]
knob.
Transmitting the Recorded Message
1. Assign the “VM1TX” (Voice Transmitting) func-
tion to the
[
C.S/VOICE
]
button using the proce-
dure in the box below.
2. Select the LSB, USB, AM, or FM mode using the
[
MODE
]
/
[
MODE
]
buttons.
3. Press the
[
C.S/VOICE
]
button to transmit the con-
tents of the voice memory you just recorded.
4. You may adjust the playback level of the record-
ing by the
[
AF GAIN
]
knob.
How to assign a function to the
[
C.S/VOICE
]
button
1. Press and hold the
[
F
]
button for one second
to enter the Menu Mode. The “ ” icon
will appear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select Menu
Item “PNL-C.S”.
3. Press the
[
DSP/SEL
]
knob to enable adjust-
ment of this Menu Item. The “ ” icon
will be blinking.
4. Rotate the
[
DSP/SEL
]
knob to select the de-
sired function.
5. Press the
[
DSP/SEL
]
knob. The “ ” icon
returns to appear continuously.
6. Press and hold the
[
F
]
button for one second
to return to normal operation.
[
F
]
button
[
DSP/SEL
]
knob
[
C.S/VOICE
]
button
[
MODE
]
/
[
MODE
]
button
[
AF GAIN
]
button
ADVICE
You may perform the Voice Memory operation
with the memory slot “VM2 (VM2REC,
VM2MONI, and VM2TX)” instead of memory
slot “VM1 (VM1REC, VM1MONI, and VM1TX)”.
Page 45FT-450D OPERATION MANUAL
SSB/AM MODE TRANSMISSION
NOTE
Page 46 FT-450D OPERATION MANUAL
The powerful CW operating capabilities of the FT-450D include operation using both an electronic keyer paddle
and a “straight key” or emulation thereof, as is provided by a computer-based keying device.
SETUP FOR STRAIGHT KEY
(
AND STRAIGHT KEY EMULATION
)
O
PERATION
Before starting, connect your key to the front panel KEY jack in the status that turned off the
[
POWER
(
ON/OFF
)]
switch, and be sure the
[
KEYER
]
button is turned off (the “ ” icon is not displayed) for now.
1. Press the
[
BAND
]
/
[
BAND
]
buttons to select
the operating band.
By pressing the
[
BAND
]
/
[
BAND
]
buttons, the
operating band will change as follows.
7 10 14 15 18 21 24.5
28 50 1.8 3.5 7
......
2. Press the
[
MODE
]
/
[
MODE
]
buttons to select
the CW mode.
3. Rotate the
[
MAIN DIAL
]
knob to adjust the oper-
ating frequency.
If you use the MH-31A8J (or MD-100A8X: option),
you may adjust the operating frequency by the
[
UP
]
/
[
DWN
]
buttons on the microphone.
4. Press the
[
F
]
button followed by the
[
STO/VOX
]
button to engage automatic activation of the trans-
mitter when you close the CW key. The “
icon will appear in the display.
5. When you close your CW key, the transmitter will
automatically be activated, and the CW carrier
will be transmitted. When your release the key,
transmission will cease after a brief delay. The
delay time is user-programmable, per the discus-
sion on page 48.
NOTE:
Do not use the plug except the 3.5-mm 3-pin type
plug. If the plug in correct size is not used the
radio may be harmed or damaged.
CW MODE OPERATION
[
F
]
button
[
MAIN DIAL
]
knob
[
KEYER
]
button
[
BAND
]
/
[
BAND
]
button
[
MODE
]
/
[
MODE
]
button
[
STO/VOX
]
button
NOTICE
Regarding of the
[
DSP/SEL
]
knob
The
[
DSP/SEL
]
knob is used for operating
various functions depending on the situation.
If you can not change the frequency/memory
channel by tuning the
[
DSP/SEL
]
knob, the
[
DSP/SEL
]
knob is selected to operate of one
of the DSP functions.
In this case, press the
[
DSP
]
button several
times until the “>” icon disappears from the
DSP Graphic Display.
Page 47FT-450D OPERATION MANUAL
USING THE BUILT-IN ELECTRONIC KEYER
Before starting, connect your keyer paddle to the front panel KEY jack in the status that turned off the
[
POWER
(
ON/
OFF
)]
switch.
1. Press the
[
BAND
]
/
[
BAND
]
buttons to select
the operating band.
By pressing the
[
BAND
]
/
[
BAND
]
buttons, the
operating band will change as follows.
7 10 14 15 18 21 24.5
28 50 1.8 3.5 7
......
2. Press the
[
MODE
]
/
[
MODE
]
buttons to select
the CW mode.
3. Rotate the
[
MAIN DIAL
]
knob to adjust the oper-
ating frequency.
If you use the MH-31A8J (or MD-100A8X: option),
you may adjust the operating frequency by the
[
UP
]
/
[
DWN
]
buttons on the microphone.
4. Press the
[
F
]
button followed by the
[
STO/VOX
]
button to engage automatic activation of the trans-
mitter when you close the CW key. The “
icon will appear in the display.
5. Press the
[
KEYER
]
button to activate the built-in
Electronic Keyer. The “ ” icon will appear in
the display.
6. When you press either the “Dot” or “Dash” side of
your paddle, the transmitter will automatically be
activated and the CW carrier will be transmitted.
When your release the paddle, transmission will
cease after a brief delay. The delay time is user-
programmable, per the discussion on page 48.
NOTE:
Do not use the plug except the 3.5-mm 3-pin type
plug. If the plug in correct size is not used the
CW MODE OPERATION
radio may be harmed or damaged.
ADJUSTING THE KEYER SPEED
1. Press and hold the
[
F
]
button for one second to
enter the Menu mode. The “ ” icon will ap-
pear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select the menu
item “CWSPEED”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment of
this menu item. The “ ” icon will be blinking.
4. Rotate the
[
DSP/SEL
]
knob while pressing either
the “Dot” or “Dash” side of your paddle, so as to
set the desired keyer speed (4 - 60 wpm).
Press the
[
F
]
button if you wish to select display
of “cpm” (characters per minute) instead of “wpm
(words per minute). The “cpm” selection is based
on the international “PARIS” standard, which stipu-
lates five characters per word.
(You may Press the
[
RCL/HOME
]
button to reset
the keyer speed to the factory default.)
5. Press the
[
DSP/SEL
]
knob. The “ ” icon re-
turns to appear continuously.
[
F
]
button
[
MAIN DIAL
]
knob
[
KEYER
]
button
[
BAND
]
/
[
BAND
]
button
[
MODE
]
/
[
MODE
]
button
[
STO/VOX
]
button
6. Press and hold the
[
F
]
button for one second to save
the new setting and return to normal operation.
TERMINOLOGY:
PARIS Word Length: By convention in the Amateur
industry (utilized by ARRL and others), the length of
one “word” of CW is defined as the length of the Morse
Code characters spelling the word “PARIS.” This char-
acter (dot/dash/space) length is used for the stan-
dard definition of code speed in “words per minute”.
[
RCL/HOME
]
button
[
F
]
button
[
DSP/SEL
]
knob

You may enable the CW keying by the
[
UP
]
/
[
DWN
]
keys of the MH-
31A8J (while the built-in
electronic keyer is en-
gaged) via menu item “CW
PADDLE”. See page 81 for
details.
DWN FST UP
Dash
Dot
Page 48 FT-450D OPERATION MANUAL
SETTING THE KEYER WEIGHT
(
DOT/SPACE:DASH
)
RATIO
The Menu Item “CWWEIGHT” may be used to adjust the Weight for the built-in Electronic Keyer. The default
weighting is 3:1 (a dash is three times longer than a dot or space).
1. Press and hold the
[
F
]
button for one second to
enter the Menu mode again. The “ ” icon
will appear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select the menu
item “CWWEIGHT”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment
of this menu item. The “
” icon will change
to blink.
4. Rotate the
[
DSP/SEL
]
knob to set the desired
keyer weight value. Available adjustment range
is for a Dot/Space:Dash ratio of “2.5” - “4.5” (de-
fault value: “3.0”).
(You may press the
[
RCL/HOME
]
button to reset
the keyer weight value to the factory default.)
5. Press the
[
DSP/SEL
]
knob. The “
” icon re-
turns to appear continuously.
6. Press and hold the
[
F
]
button for one second to save
the new setting and return to normal operation.
USING THE BUILT-IN ELECTRONIC KEYER
SELECTING THE KEYER PADDLE
S WIRING CONFIGURATION
You may select “normal” or “reverse” paddle polarity via Menu Item “CW KEY”. The default setting is “normal”,
whereby the “Tip” connection on the key plug is “Dot” and the “Ring” connection is “Dash”.
[
RCL/HOME
]
button
[
F
]
button
[
DSP/SEL
]
knob

To change the paddle polarity:
1. Press and hold the
[
F
]
button for one second to
enter the Menu mode again. The “ ” icon
will appear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select the menu
item “CW KEY”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment
of this menu item. The “ ” icon will be blink-
ing.
4. Rotate the
[
DSP/SEL
]
knob to set the “REV” (de-
fault: “NOR”).
(You may Press the
[
RCL/HOME
]
button to reset
the paddle polarity to the factory default.)
5. Press the
[
DSP/SEL
]
knob. The “ ” icon re-
turns to appear continuously.
6. Press and hold the
[
F
]
button for one second to save
the new setting and return to normal operation.
[
RCL/HOME
]
button
[
F
]
button
[
DSP/SEL
]
knob
CW MODE OPERATION
Page 49FT-450D OPERATION MANUAL
CW SPOTTING
(
ZERO-BEATING
)
“Spotting” (zeroing in on another CW station) is a handy technique for ensuring that you and the other station are
precisely on the same frequency.
CW MODE OPERATION
TO USE CW SPOTTING:
In CW mode, while pressing and holding the
[
IPO/ATT
]
button, the Spot tone will be heard and Spot
tone frequency will show in the display. This tone cor-
responds to the pitch of your transmitted signal, and
if you adjust the receiver frequency to match the pitch
of the received CW signal to that of the Spot tone,
your transmitted signal will be precisely matched to
that of the other station.
Release the
[
IPO/ATT
]
button to turn the Spot tone off.
USING CW REVERSE
If you experience a difficult interference situation, where an interfering station cannot readily be eliminated, you
may wish to try receiving using the opposite sideband. This may throw the interfering station’s frequency in a
direction that may lend itself more readily to rejection.
1. To start, let’s use a typical example where you
have set the CW mode (using the default “USB”
injection: the “ ” and “ ” icon appear).
2. Press and hold in the
[
MODE
]
or
[
MODE
]
button for one second. The “ ” icon appears
instead of “ ”, indicating that the “LSB” injec-
tion side has now been selected.
3. Press and hold in the
[
MODE
]
or
[
MODE
]
button, once again, for one second to return to
the normal (USB) injection side and cancel CW
Reverse operation (the “ ” and “ ” icons
appear).
[
IPO/ATT
]
button
In the illustration, Figure A demonstrates the
normal CW injection setup, using the USB
side. In Figure B, CW Reverse has been en-
gaged, so as to receive using LSB-side in-
jection to eliminate interference.
The beneficial effect of switching sidebands
can clearly be seen in this example.
RX Passband
RX Passband
Carrier
Carrier
QRM
QRM
Normal CW
( )
CW Reverse
( )
USB
LSB
A
B
[
MODE
]
/
[
MODE
]
button
Page 50 FT-450D OPERATION MANUAL
CW DELAY TIME SETTING
During semi-break-in (not QSK) operation, the hang time of the transmitter, after you have finished sending, may
be adjusted to a comfortable value consistent with your sending speed. This is the functional equivalent to the
“VOX Delay” adjustment used on voice modes, and the delay may be varied anywhere between 30 - 3000
millisecond (10 millisecond step) and FULL (Full Break-in operation).
1. Press and hold the
[
F
]
button for one second to
enter the Menu mode. The “ ” icon will ap-
pear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select the menu
item “CW DLY”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment
of this menu item. The “ ” icon will be blink-
ing.
4. Rotate the
[
DSP/SEL
]
knob to set the desired de-
lay time.
If the delay selection is set to “FULL”, the trans-
ceiver operates in the full break-in mode (allow-
ing you to hear between the characters that are
being sent).
(You may press the
[
RCL/HOME
]
button to reset
the delay time to the factory default.)
CW SIDETONE VOLUME LEVEL SETTING
You may adjust the CW sidetone volume level via the Menu Item “CWSTONE”.
1. Press and hold the
[
F
]
button for one second to
enter the Menu mode. The “ ” icon will ap-
pear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select the menu
item “CWSTONE”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment
of this menu item. The “ ” icon will be blink-
ing.
4. While pressing and holding the
[
METER/DIM
]
but-
ton, rotate the
[
DSP/SEL
]
knob to set the desired
sidetone volume level (FIX 0 - FIX 100).
If you wish to adjust the CW sidetone level with
the
[
AF GAIN
]
knob, press the
[
F
]
key to change
the display to “LNK-xx” then rotate the
[
DSP/SEL
]
knob to set the volume ratio of the CW sidetone
volume level for the receiving audio volume level.
Available selections are LNK-50 ~ LNK 0 ~
LNK+50. When the LNK 0 is selected, the CW
sidetone volume level becomes the same as re-
ceiving audio volume level.
(You may press the
[
RCL/HOME
]
button to reset
the CW sidetone level to the factory default.)
5. Press the
[
DSP/SEL
]
knob. The “ ” icon re-
turns to appear continuously.
6. Press and hold the
[
F
]
button for one second to
save the new setting and return to normal opera-
tion.
5. Press the
[
DSP/SEL
]
knob. The “ ” icon
returns to appear continuously.
6. Press and hold the
[
F
]
button for one second to
save the new setting and return to normal opera-
tion.
[
RCL/HOME
]
button
[
F
]
button
[
DSP/SEL
]
knob
CW MODE OPERATION
[
RCL/HOME
]
button
[
F
]
button
[
DSP/SEL
]
knob
[
METER/DIM
]
button
Page 51FT-450D OPERATION MANUAL
CW PITCH ADJUSTMENT
You may adjust the center frequency of the receiver passband, as well as the pitch of your offset CW carrier via
the Menu Item “CWPITCH”. Available tone selections are 400 Hz through 800 Hz, in 100 Hz step.
CW MODE OPERATION
1. Press and hold the
[
F
]
button for one second to
enter the Menu mode. The “ ” icon will ap-
pear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select the menu
item “CWPITCH”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment
of this menu item. The “ ” icon will be blink-
ing.
4. While pressing and holding the
[
METER/DIM
]
but-
ton, rotate the
[
DSP/SEL
]
knob to set the desired
pitch frequency.
(You may press the
[
RCL/HOME
]
button to reset
the pitch frequency to the factory default.)
5. Press the
[
DSP/SEL
]
knob. The “ ” icon re-
turns to appear continuously.
6. Press and hold the
[
F
]
button for one second to
save the new setting and return to normal opera-
tion.
CW TRAINING FEATURE
The FT-450D provides a unique CW Training feature, which sends random Morse Code five-character groups
via the sidetone (heard in the speaker), so you can improve your CW proficiency whether or not the bands are
open.
1. Press and hold the
[
F
]
button for one second to
enter the Menu mode. The “ ” icon will ap-
pear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select the menu
item “CWTRAIN”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment
of this menu item. The “ ” icon will be blink-
ing.
4. Rotate the
[
DSP/SEL
]
knob to select the training
mode:
N: Numeric character only
A: Alphabet character only
M: Numeric and Alphabet characters (Mixed)
5. Press the
[
F
]
button to begin generation of the
five character code groups (CW sidetone only,
does not key the transmitter).
6. When the code group is completed, the “Answer”
will appear on the display.
7. Press the
[
DSP/SEL
]
knob. The “ ” icon re-
turns to appear continuously.
8. Press the
[
F
]
button to generate another code
group, as above.
9. To disable the CW Training feature, press and
hold the
[
F
]
button for one second to return to
normal operation.
NOTE:
You may adjust the Morse Speed via Menu Item
CWSPEED”.
You may adjust the sidetone volume level via
Menu Item “CWSTONE”.
[
F
]
button
[
DSP/SEL
]
knob
[
RCL/HOME
]
button
[
F
]
button
[
METER/DIM
]
button
[
DSP/SEL
]
knob
Page 52 FT-450D OPERATION MANUAL
BEACON FEATURE
The FT-450D’s unique “Beacon” feature allows you to set up the transceiver to send a repetitive message. For
example, on a DX-pedition, the FT-450D beacon might be activated on a 50 MHz frequency, to alert DXers to
possible band openings.
CW MODE OPERATION
BEACON TEXT STORAGE
1. Press and hold the
[
F
]
button for one second to
enter the Menu mode again. The “ ” icon
will appear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select the menu
item “BCN TXT”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment
of this menu item. The “ ” icon will be blink-
ing.
4. Rotate the
[
MAIN DIAL
]
knob to select “1:1- - - -”.
5. Rotate the
[
DSP/SEL
]
knob one click clockwise
to enable storage of the Beacon Text.
6. Rotate the
[
MAIN DIAL
]
knob to select the first
character (number or letter) in the Beacon Text you
wish to store. Then rotate the
[
DSP/SEL
]
knob one
click clockwise to move to the next character.
Available characters are A - Z, 0 - 9, /, , space
and @ character.
7. Repeat step 6 as many times as necessary to
complete the Beacon Text.
If the Beacon Text is more than 40 charac-
ters long, but less than 79, set the last (40th)
character to be “,” press the
[
DSP/SEL
]
knob twice, then rotate the
[
MAIN DIAL
]
knob
to select “2:2- - - -”. Now repeat step 6.
If the Beacon Text is more than 79 charac-
ters long, but less than 118 characters may
be stored. In this case, set the final character
slot in “2:” to be “”, press the
[
DSP/SEL
]
knob twice, and then rotate the
[
MAIN DIAL
]
knob to select “3:3- - - -”. Now repeat step 6.
8. Press and hold the
[
F
]
button for one second to save
the new setting and return to normal operation.
SET THE BEACON INTERVAL TIME
1. Press and hold the
[
F
]
button for one second to
enter the Menu mode again. The “ ” icon
will appear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select the menu
item “BCN TIM”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment
of this menu item. The “ ” icon will be blink-
ing.
4. Rotate the
[
DSP/SEL
]
knob to select the interval
time (between message and message) Available
selections are 1 - 255 second or off.
5. Press the
[
DSP/SEL
]
knob. The “ ” icon re-
turns to appear continuously.
6. Press and hold the
[
F
]
button for one second to save
the new setting and return to normal operation.
[
MAIN DIAL
]
knob
[
RCL/HOME
]
button
[
F
]
button
[
DSP/SEL
]
knob
Page 53FT-450D OPERATION MANUAL
CW MODE OPERATION
BEACON TRANSMISSION
(
ON THE AIR
)
1. Press and hold the
[
F
]
button for one second to
enter the Menu mode. The “ ” icon will ap-
pear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select menu item
PNL-C.S”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment
of this menu item. The “ ” icon will be blink-
ing.
4. Rotate the
[
DSP/SEL
]
knob to select “PLAY1”.
5. Press the
[
DSP/SEL
]
knob. The “ ” icon re-
turns to appear continuously.
6. Press and hold the
[
F
]
button for one second to save
the new setting and return to normal operation.
7. Set the operating mode to CW.
8. Press the
[
C.S/VOICE
]
button to activate the Bea-
con Feature (transmit the CW Beacon).
The “PLAY1” notation appears on the display while
sending the beacon, and the “BEACON” notation
appears on the display between transmissions.
To disable the transmission from the Beacon, press
the
[
C.S/VOICE
]
button again.
MANUAL BEACON TRANSMISSION
You may also send the Beacon text manually. If this
is done, all three “Beacon” messages may be used
as a traditional CW message keyer. To do this:
1. Repeat the “Set the Beacon Interval Time” pro-
cedure described previously, rotating the
[
DSP/
SEL
]
knob to select “off” in step 4.
2. Repeat the “Beacon Transmission (On the Air)”
procedure, rotating the
[
DSP/SEL
]
knob to se-
lect “PLAY2” if you wish to send the message
manually which is stored in bank “1”, “2”, or
PLAY3” if you wish to send the message manu-
ally which is stored in bank “3” in step 4.
3. Press the
[
C.S/VOICE
]
button to activate the Bea-
con Feature (transmit the CW Beacon).
BEACON FEATURE
[
C.S/VOICE
]
button
[
F
]
button
[
DSP/SEL
]
knob
[
C.S/VOICE
]
button
Page 54 FT-450D OPERATION MANUAL
PHONES
KEY
BASIC OPERATION
1. Press the
[
BAND
]
/
[
BAND
]
buttons to select
the 28 MHz or 50 MHz.
Note: FM is only used in the 28 MHz and 50 MHz
Amateur bands covered in the FT-450D. Please
do not use FM on any other bands.
2. Press the
[
MODE
]
/
[
MODE
]
buttons to select
the FM mode.
3. Rotate the
[
MAIN DIAL
]
knob to adjust the oper-
ating frequency.
If you use the MH-31A8J (or MD-100A8X: option),
you may adjust the operating frequency by the
[
UP
]
/
[
DWN
]
buttons on the microphone.
4. Press the microphone’s PTT (Push To Talk)
switch to begin transmission. Speak into the mi-
crophone in a normal voice level.
The “ ” icon will appear in the display, con-
firming that transmission is in progress.
5. Release the PTT switch at the end of your trans-
mission. The transceiver will return to the receive
mode.
FM MODE OPERATION
NOTE:
In the FM mode, the squelch circuit is set to the
threshold point automatically.
However, when turn the
[
SQL/RF GAIN
]
knob
counter-clockwise, the squelch circuit is turned
off.
Keep the
[
SQL/RF GAIN
]
knob always clockwise
position.
You may change the
[
SQL/RF GAIN
]
knob from
the RF GAIN function to the squelch function via
Menu item SQL/RFG.
At the factory, a microphone gain has been pro-
grammed that should be satisfactory for the sup-
plied MH-31A8J Hand Microphone. If you use an
after-market microphone, you may wish to set a
different Microphone Gain Level, described pre-
viously (Microphone Gain Level Adjustment: see
page 39)
[
MAIN DIAL
]
knob
[
BAND
]
/
[
BAND
]
button
[
MODE
]
/
[
MODE
]
button
NOTICE
Regarding of the
[
DSP/SEL
]
knob
The
[
DSP/SEL
]
knob is used for operating
various functions depending on the situation.
If you can not change the frequency/memory
channel by tuning the
[
DSP/SEL
]
knob, the
[
DSP/SEL
]
knob is selected to operate of one
of the DSP functions.
In this case, press the
[
DSP
]
button several
times until the “>” icon disappears from the
DSP Graphic Display.
Page 55FT-450D OPERATION MANUAL
REPEATER OPERATION
The FT-450D may be operated on 29 MHz and 50 MHz repeaters. Use this procedure to set the repeater shift
direction, and the CTCSS squelch mode & tone.
1. Press and hold the
[
F
]
button for one second to
enter the Menu mode again. The “ ” icon
will appear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select the menu
item “RPT”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment
of this menu item. The “ ” icon will change
to blink.
4. Rotate the
[
DSP/SEL
]
knob to select the desired
repeater shift direction. Available selections are
–SHIFT, SIMPLEX, and +SHIFT.
5. Press the
[
DSP/SEL
]
knob. The “ ” icon re-
turns to appear continuously.
6. Rotate the
[
DSP/SEL
]
knob to select the menu
item “SQL TYP”.
7. Press the
[
DSP/SEL
]
knob to enable adjustment of
this menu item. The “ ” icon will be blinking.
8. Rotate the
[
DSP/SEL
]
knob to select the desired
CTCSS mode. If you just need to send the uplink
encoding tone, select “ENC”. For encode/decode
operation, choose “ENC DEC” instead.
9. Press the
[
DSP/SEL
]
knob. The “ ” icon re-
turns to appear continuously.
10. Rotate the
[
DSP/SEL
]
knob to select the menu
item “TONE F”.
11. Press the
[
DSP/SEL
]
knob to enable adjustment of
this menu item. The “ ” icon will be blinking.
12. Rotate the
[
DSP/SEL
]
knob to select the desired
CTCSS tone to be used. A total of 50 standard
CTCSS tones are provided.
13. Press the
[
DSP/SEL
]
knob. The “ ” icon re-
turns to appear continuously.
14. Press and hold the
[
F
]
button for one second to save
the new setting and return to normal operation.
15. Rotate the
[
MAIN DIAL
]
to the output frequency
(downlink) from the repeater.
16. Close the microphone’s PTT switch to begin
transmission. You will observe that the frequency
has shifted to correspond to the programming you
set up in the previous steps. Speak into the mi-
crophone in a normal voice level, and release the
PTT switch to return to the receive mode.
FM MODE OPERATION
AD VICE:
The conventional repeater shift used on 29 MHz is
100 kHz, while on the 50 MHz band the shift may
vary between 500 kHz and 1.7 MHz (or more). To
program the proper repeater shift, use Menu Item
RPT SFT”.
[
F
]
button
[
DSP/SEL
]
knob
[
MAIN DIAL
]
knob
CTCSS TONE FREQUENCY
(
Hz
)
67.0 69.3 71.9 74.4 77.0 79.7 82.5 85.4
88.5 91.5 94.8 97.4 100.0 103.5 107.2 110.9
114.8 118.8 123.0 127.3 131.8 136.5 141.3 146.2
151.4 156.7 159.8 162.2 165.5 167.9 171.3 173.8
177.3 179.9 183.5 186.2 189.9 192.8 196.6 199.5
203.5 206.5 210.7 218.1 225.7 229.1 233.6 241.8
250.3 251.4
Page 56 FT-450D OPERATION MANUAL
TONE SQUELCH OPERATION
You may also use “Tone Squelch” whereby your receiver will be kept silent until an incoming signal bearing a
matching CTCSS tone is received. Your receiver’s squelch will then open in response to the reception of the
required tone.
1. Press and hold the
[
F
]
button for one second to
enter the Menu mode again. The “ ” icon
will appear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select menu item
SQL TYP”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment of
this menu item. The “ ” icon will be blinking.
4. Rotate the
[
DSP/SEL
]
knob to select the “ENC
DEC”.
5. Press the
[
DSP/SEL
]
knob. The “ ” icon re-
turns to appear continuously.
6. Rotate the
[
DSP/SEL
]
knob to select menu item
TONE F”, then press the
[
DSP/SEL
]
knob to en-
able adjustment of this menu item.
7. Rotate the
[
DSP/SEL
]
knob to select the desired
CTCSS tone to be used. A total of 50 standard
CTCSS tones are provided.
8. Press the
[
DSP/SEL
]
knob. The “ ” icon re-
turns to appear continuously.
9. Press and hold the
[
F
]
button for one second to save
the new setting and return to normal operation.
When Tone Squelch is activated, the “ ” icon
appears in the display.
FM MODE OPERATION
[
F
]
button
[
DSP/SEL
]
knob
CTCSS TONE FREQUENCY
(
Hz
)
67.0 69.3 71.9 74.4 77.0 79.7 82.5 85.4
88.5 91.5 94.8 97.4 100.0 103.5 107.2 110.9
114.8 118.8 123.0 127.3 131.8 136.5 141.3 146.2
151.4 156.7 159.8 162.2 165.5 167.9 171.3 173.8
177.3 179.9 183.5 186.2 189.9 192.8 196.6 199.5
203.5 206.5 210.7 218.1 225.7 229.1 233.6 241.8
250.3 251.4
Page 57FT-450D OPERATION MANUAL
FM MODE OPERATION
TONE SEARCH SCANNING
In operating situations where you don’t know the CTCSS tone being used by another station or stations, you can
command the radio to listen to the incoming signal and scan in search of the tone being used. Two things must
be remembered in this regard:
You must be sure that your repeater uses the same tone type (CTCSS).
Some repeaters do not pass the CTCSS tone; you may have to listen to the station(s) transmitting on the
repeater uplink (input) frequency in order to allow Tone Search Scanning to work.
To scan for the tone in use:
1. Set the radio up for CTCSS operation (see the
previous discussion). The “ ” icon will
appear on the display.
2. Press and hold the
[
F
]
button for one second to
enter the Menu mode. The “ ” icon will ap-
pear on the display.
3. Rotate the
[
DSP/SEL
]
knob to select the menu
item “TONE F”.
4. Press the
[
DSP/SEL
]
knob to enable adjustment
of the selected Menu Item. The “ ” icon will
be blinking.
5. Press the
[
SCAN/PMS
]
button to start scanning
for the incoming CTCSS tone.
6. When the radio detects the correct tone, it will
halt on that tone, and audio will be allowed to pass.
7. Press the
[
DSP/SEL
]
knob to lock in that tone.
8. Press and hold the
[
F
]
button for one second to
return to normal operation.
NOTE:
If the Tone Scan feature does not detect a tone, it will
continue to scan indefinitely. When this happens, it
may be that the other station is not sending any tone.
You can press the
[
SCAN/PMS
]
button to halt the
scan at any time.
[
SCAN/PMS
]
button
[
F
]
button
[
DSP/SEL
]
knob
Page 58 FT-450D OPERATION MANUAL
(UK5 -FM)
(UK5 -FE)
(UK5-FL)
(UK5 -FK)
MEM-001
(UK5-FA)
MEM-498
MEM-002 (UK5-FB)
MEM-499
MEM-003
(UK5 -FC)
MEM-500
QMB
US5-005
US5-004
US5-001
US5-002
US5-003
MEMORY OPERATION
CONVENIENT MEMORY FUNCTIONS
The FT-450D contains 500 regular memories, labeled “MEM-001” through “MEM-500”, two Home channels,
one for the HF band and another for the 50 MHz band, two special programmed limit memory pairs, labeled
MEM-P1L/MEM-P1U” and “MEM-P2L/MEM-P2U”, one QMB (Quick Memory Bank) memory, one Alaska Emer-
gency Frequency Channel (5167.5 kHz), and five 60-meter (5 MHz) band channels (US version only). and seven
60-meter (5 MHz) band channels (UK version only). Each (except the Alaska Emergency Frequency Channel
and 60-meter Band channels, which are fixed.) stores various settings, in addition to the frequency and mode
(See below). By default, the 500 regular memories are contained in one group; however, they can be arranged
in up to 10 separate groups, if desired.
Quick Point:
The FT-450D’s memory channels store the following data:
Ì Operating Frequency
Ì Operating Mode
Ì NARROW / WIDE FM bandwidth status
Ì ATT status
Ì IPO status
Ì CONTOUR status and its Peak Frequency
Ì DSP Noise Reduction (DNR) status and its Reduction algorithm selection.
Ì DSP Notch filter (NOTCH) status
Ì Repeater Shift Direction
Ì CTCSS Tone Frequency
IMPORTANT NOTE:
On a rare occasion the memory data may be lost or corrupted due to static electricity, electrical noise or errone-
ous operation. Parts changes or repairs may cause memory loss. Be sure to write down or record your data so
you will be able to restore it.
REGULAR MEMORY CHANNELS (500 ch)
PMS M
EMORY CHANNELS
(2 ch)
QMB MEMORY CHANNEL (1 ch)
60-
METER (5 MHZ) BAND CHANNELS (5 ch) : U.S. VERSION ONLY
60-METER (5 MHZ) BAND CHANNELS (7 ch): U.K. VERSION ONLY
Page 59FT-450D OPERATION MANUAL
M
EMORY
O
PERATION
MEMORY GROUPS
Memory channels may be organized into as many as 10 convenient groups, for easy identification and selec-
tion. For example, you might want to set aside memory groups for AM BC stations, shortwave broadcast
stations, contest frequencies, repeater frequencies, and PMS limits, or any other groupings you like.
Each memory group is capable of holding up to 50 memory channels (the Group size is fixed). When a
memory channel is grouped, the channel numbers change to correspond to the chart below:
Memory Channel Number
Group Memory ”OFF” Group Memory ”ON”
MEM-001 ~ MEM-050 M-01-01 ~ M-01-50
MEM-051 ~ MEM-100 M-02-01 ~ M-02-50
MEM-101 ~ MEM-150 M-03-01 ~ M-03-50
MEM-151 ~ MEM-200 M-04-01 ~ M-04-50
MEM-201 ~ MEM-250 M-05-01 ~ M-05-50
MEM-251 ~ MEM-300 M-06-01 ~ M-06-50
MEM-301 ~ MEM-350 M-07-01 ~ M-07-50
MEM-351 ~ MEM-400 M-08-01 ~ M-08-50
MEM-401 ~ MEM-450 M-09-01 ~ M-09-50
MEM-450 ~ MEM-500 M-10-01 ~ M-10-50
MEM-P1L ~ MEM-P2U M-11-1L ~ M-11-2U
MEM-EMG M-12-EM
US5-001 ~ US5-005 M-13-01 ~ M-13-05
(UK5-FA ~ UK5-FM)
(M-13-FA ~ M-13-FM)
Memory Group Assignment:
1. Press and hold the
[
F
]
button for one second to
enter the Menu mode again. The “ ” icon
will appear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select the menu
item “MEM GRP”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment
of this menu item. The “ ” icon will be blink-
ing.
4. Rotate the
[
DSP/SEL
]
knob to select “ON”.
5. Press the
[
DSP/SEL
]
knob. The “ ” icon re-
turns to appear continuously.
6. Press and hold the
[
F
]
button for one second to
save the new setting and return to normal opera-
tion.
To cancel Memory Group operation, repeat above
steps, choosing “OFF” in step 4.
[
DSP/SEL
]
Knob
[
F
]
button
: UK version ony.
Page 60 FT-450D OPERATION MANUAL
M
EMORY
O
PERATION
REGULAR MEMORY OPERATION
The Regular Memory of the FT-450D allows storage and recall of up to 500 memories, each storing frequency,
mode, and a wide variety of status information detailed previously. Memories may be organized into as many as
ten Memory Groups, and additionally you get two pairs of band-limit (PMS) memories along with one QMB
(Quick Memory Bank) memory and two Home channels.
Memory Storage
1. In the VFO mode, select the desired frequency,
mode, and status the way you want to have it
stored.
2. Press the
[
F
]
button followed by the
[
V/M/MW
]
button.
The blinking current memory channel number will
be shown on the display, and the contents of the
current memory channel will be shown on the dis-
play.
If there is no action by you within 90 second from
releasing the
[
V/M/MW
]
button the Memory Stor-
age procedure is canceled.
The memory storage procedure is canceled un-
less you operate it within 90 seconds.
3. Rotate the
[
DSP/SEL
]
knob to select the memory
channel in which you wish to store the data. If you
have selected a channel on which data is already
stored, that frequency will appear on the display.
4. Press the
[
V/M/MW
]
button momentarily to store
the frequency and other data into the selected
memory channel. A beep will confirm that you have
held the
[
V/M/MW
]
button.
You may over write new data into a channel on which
data is already stored.
Memory Channel Recall
1. Press the
[
V/M/MW
]
button, if necessary, to enter
the Memory mode. A memory channel number will
appear in the display.
2. Rotate the
[
DSP/SEL
]
knob to select the desired
memory channel.
Advice:
To work within a particular Memory Group, press the
[
DSP/SEL
]
button. Then rotate the
[
DSP/SEL
]
knob
to select the desired Memory Group. Now press the
[
DSP/SEL
]
button again. You may now choose the
memory channel within the selected Memory Group.
[
DSP/SEL
]
Knob
[
V/M
/MW
]
button
[
DSP/SEL
]
Knob
[
V/M
/MW
]
button
Page 61FT-450D OPERATION MANUAL
M
EMORY
O
PERATION
Erasing Memory Channel Data
1. Press the
[
V/M/MW
]
button, if necessary, to enter
the Memory mode.
2. Press the
[
F
]
button followed by the
[
V/M/MW
]
button.
The blinking current memory channel number will
be shown on the display, and the contents of the
current memory channel will be shown on the dis-
play.
3. Rotate the
[
DSP/SEL
]
knob to select the memory
channel that you would like to erase.
4. Press the
[
CLAR
]
button to erase the contents of
the selected memory channel.
5. Press the
[
V/M/MW
]
button momentarily to erase
the selected memory channel. The display will
revert to memory channel 1.
AD VICE:
After erasure, only the memory channel number will
remain. The frequency data will disappear from the
display.
If you make a mistake and wish to restore the
memory’s contents, just repeat above steps.
Memory Tune Operation
You may freely tune off of any memory channel in the
“Memory Tune” mode, this is similar to VFO opera-
tion. So long as you do not over-write the contents of
the current memory, Memory Tune operation will not
alter the contents of the memory channel.
1. Press the
[
V/M/MW
]
button, if necessary, to enter
the Memory mode.
2. Rotate the
[
MAIN DIAL
]
knob. You will now ob-
serve that the memory channel’s frequency is
changing.
The “M-TUNE” notation will replace the Memory
Channel Number, indicating you are in the
“Memory Tune” mode.
During Memory Tune operation, you may change
operating modes, and engage and offset the Clari-
fier, if desired.
3. Press the
[
V/M/MW
]
button momentarily to return
to the originally-memorized frequency of the cur-
rent memory channel. One more press of the
[
V/M/MW
]
button will return you to VFO opera-
tion.
[
DSP/SEL
]
Knob
[
V/M
/MW
]
button
REGULAR MEMORY OPERATION
[
F
]
button
[
CLAR
]
button
[
MAIN DIAL
]
Knob
[
V/M/MW
]
button
Page 62 FT-450D OPERATION MANUAL
M
EMORY
O
PERATION
Labeling Memories
You may wish to append an Alphanumeric “Tag” (label) to a memory or memories, to aid in recollection of the
channel’s use (such as a club name, etc.). This is easily accomplished using the Menu mode.
REGULAR MEMORY OPERATION
1. Recall the memory channel that you wish to ap-
pend a label.
2. Press and hold the
[
F
]
button for one second to
enter the Menu mode again. The “ ” icon
will appear on the display.
3. Rotate the
[
DSP/SEL
]
knob to select the menu
item “MEM TAG”.
4. Press the
[
DSP/SEL
]
knob to enable adjustment
of this menu item. The “ ” icon will blink,
and “MEM TAG” will be replaced with “TAG-OFF
5. Press the [F] button to display the previously stored
label (in the factory default, all memory channels
are stored with the memory channel number as
the label).
6. Rotate the
[
MAIN DIAL
]
knob to select the first
digit of the desired label.
7. Rotate the
[
DSP/SEL
]
knob one step clockwise
to move to the next character.
8. Repeat steps 6 and 7 to program the remaining
letters, numbers, or symbols of the desired label.
Seven characters may be used in the creation of
a label.
9. If you make a mistake, rotate the
[
DSP/SEL
]
knob
counter-clockwise to move back the cursor, then
re-enter the correct letter, number, or symbol.
You may press the [CLAR] button to clear the cur-
rent digit label.
10.When you have completed the creation of the la-
bel, press the
[
DSP/SEL
]
knob. The “ ” icon
returns to appear continuously.
11. Press and hold the
[
F
]
button for one second to
save the new setting and return to normal opera-
tion.
In Memory mode operation, the display indicates the
channel numbers while selecting the memory chan-
nels, then the display will switch to the Alphanumeric
“Tag” (label) after two seconds.
[
DSP/SEL
]
Knob
[
V/M/MW
]
button
[
F
]
button
[
MAIN DIAL
]
Knob
[
CLAR
]
button
Page 63FT-450D OPERATION MANUAL
M
EMORY
O
PERATION
To disable the Alphanumeric “Tag” (label) display.
1. Recall the memory channel that you wish to dis-
able the Alphanumeric “Tag” (label).
2. Press and hold the [F] button for one second to
enter the Menu mode again. The “ ” icon
will appear on the display.
3. Rotate the
[
DSP/SEL
]
knob to select the menu
item “MEM TAG”.
4. Press the
[
DSP/SEL
]
knob to enable adjustment
of this menu item. The “ ” icon will blink and
the “MEM TAG” notation will be replaced with the
Alphanumeric “Tag” (label).
5. Press the
[
F
]
button. The “ ” icon returns to
appear continuously and the Alphanumeric “Tag”
(label) will be replaced with the “TAG-OFF” nota-
tion.
6. Press and hold the
[
F
]
button for one second to
save the new setting and return to normal opera-
tion.
REGULAR MEMORY OPERATION
[
DSP/SEL
]
Knob
[
F
]
button
Page 64 FT-450D OPERATION MANUAL
M
EMORY
O
PERATION
HOME CHANNEL MEMORIES
Two one-touch “Home” channels are available, for special frequencies you use often.
The HF band Special “Home” channel default is 29.300 MHz or 29.600 MHz, FM. The 50 MHz band “Home”
channel default is 50.100 MHz, 51.000 MHz, or 52.525 MHz, FM (depends on the transcever’s version).
Home Channel Recall
1. Press the
[
F
]
button, followed by the
[
RCL/HOME
]
button to recall the Home Channel on the band
group where you currently are operating (HF or
50 MHz). The “HOME” notation appears in the dis-
play.
2. Press the [F] button, followed by the
[
RCL/HOME
]
button to return to the previous-used frequency
(either a VFO or a memory channel).
The transceiver switches to VFO mode if either the
[
DSP/SEL
]
knob or
[
MAIN DIAL
]
knob is turned. (In
AM/FM modes the menu item “A&FDIAL” should be
set to “ON” for the
[
MAIN DIAL
]
to be active).
Home Channel Frequency Change
The factory default for the Home Channel is 29.300 MHz, FM for HF band and 51.000 MHz, FM for 50 MHz
band. You can re-program the Home Channel in a manner identical to that used for the regular memories:
1. In the VFO mode, select the desired frequency,
mode, and status the way you want to have it
stored.
2. Press the
[
F
]
button followed by the
[
V/M/MW
]
button.
The blinking current memory channel number will
be shown on the display, and the contents of the
current memory channel will be shown on the dis-
play.
If there is no action by you within 10 second from
releasing the
[
V/M/MW
]
button the Memory Stor-
age procedure is canceled.
The memory storage procedure is canceled un-
less you operate it within 10 seconds
3. Press the
[
RCL/HOME
]
button momentarily to
store the frequency and other data into the Home
Channel. A double beep will confirm that you have
held the
[
RCL/HOME
]
button in long enough.
[
DSP/SEL
]
Knob
[
RCL/HOME
]
button
[
F
]
button
[
MAIN DIAL
]
Knob
[
V/M/MW
]
button
[
F
]
button
[
RCL/HOME
]
button
Page 65FT-450D OPERATION MANUAL
M
EMORY
O
PERATION
QMB
(
QUICK MEMORY BANK
)
The Quick Memory Bank is independent from the regular and PMS memories. You can quickly store operating
parameters for later recall.
Storage
1. Tune to the desired frequency on the VFO mode.
2. Press the
[
STO/VOX
]
button momentarily. The
“beep” will confirm that the contents of the VFO
have been written to the QMB memory.
Recall
1. Press the
[
RCL/HOME
]
button. The QMB
channel’s data will be shown on the display.
2. Press the
[
RCL/HOME
]
button to return to the
previous-used frequency (either a VFO or a
memory channel).
Advice:
Rotating the
[
MAIN DIAL
]
knob, or changing the op-
erating mode, will place the transceiver in the
“Memory Tune” mode (The “QMB” notation will re-
place the “MT-QMB” in the display), which is a tem-
porary “pseudo-VFO” method of tuning off of a stored
memory channel. If you do not over-write the con-
tents of the current memory channel, the original con-
tents will not be disturbed by the initiation of Memory
Tune operation. Press the
[
RCL/HOME
]
button to
return original QMB frequency and/or operating mode.
[
STO/VOX
]
button
[
RCL/HOME
]
button
Page 66 FT-450D OPERATION MANUAL
S
CANNING
O
PERATION
You may scan either the VFO or the memories of the FT-450D, and the radio will halt the scan on any station with
a signal strong enough to open the receiver’s squelch.
VFO AND MEMORY SCANNING
Preparation
When operating the Scanning feature, set the con-
figuration of the
[
SQL/RF GAIN
]
knob to “Squelch”
via the Menu Item “SQL/RFG”.
1. Press and hold the
[
F
]
button for one second to
enter the Menu mode again. The “ ” icon
will appear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select the menu
item “SQL/RFG”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment
of this menu item. The “ ” icon will be blink-
ing.
4. Rotate the
[
DSP/SEL
]
knob to select “SQL” to as-
sign the Squelch feature to the
[
SQL/RF GAIN
]
knob.
5. Press the
[
DSP/SEL
]
knob. The “ ” icon re-
turns to appear continuously.
6. Press and hold the
[
F
]
button for one second to
save the new setting and return to normal opera-
tion.
[
DSP/SEL
]
Knob
[
F
]
button
[
SQL/RF GAIN
]
Knob
Page 67FT-450D OPERATION MANUAL
S
CANNING
O
PERATION
VFO/Memory Scan
1. Rotate the
[
SQL/RF GAIN
]
knob just to the point
where the noise is silenced and the “ ” indi-
cator on the display turns off.
2. Press the
[
SCAN/PMS
]
key to initiate upward
scanning (toward higher frequencies or higher
memory channel numbers).
3. If you want to change direction of the scan while it
is underway, rotate the
[
MAIN DIAL
]
knob one click
in the opposite direction (in this case, one click
counter-clockwise). You will see the scanner re-
verse direction and scan down in frequency.
You may change the direction of the scanner by
pressing and holding the microphone’s
[
UP
]
/
[
DWN
]
key for one second, if you are using the
MH-31A8J Hand Microphone or optional MD-
100A8X Desktop Microphone.
4. In FM/AM mode, when the scanner encounters a
signal strong enough to open the squelch, the
scanner will halt for five seconds, after which scan-
ning will resume.
In the SSB/CW and SSB-based Data modes,
when the scanner encounters a signal strong
enough to open the squelch, the scanner will step
across the signal very slowly, giving you time to
stop the scan, if you like.
5. To stop the scanner, press the
[
SCAN/PMS
]
but-
ton or PTT switch.
AD VICE:
You may select the manner in which the scanner re-
sumes while it has paused on a signal, using Menu
Item “SCN RES” The default “5Sec” setting will cause
the scanner to resume scanning after five seconds;
you may change it, however, to resume only after the
carrier has dropped out, if you like See page 85.
During Memory Group operation, only the channels
within the current Memory Group will be scanned.
[
DSP/SEL
]
Knob
[
SCAN/PMS
]
button
[
SQL/RF GAIN
]
Knob
VFO AND MEMORY SCANNING
[
MAIN DIAL
]
Knob
Page 68 FT-450D OPERATION MANUAL
P
ROGRAMMABLE
M
EMORY
S
CANNING
(
PMS
)
To limit scanning (and manual tuning) within a particular frequency range, you can use the Programmable
Memory Scanning (PMS) feature, which utilizes two special-purpose memory pairs (“MEM-P1L/MEM-P1U” and
“MEM-P2L/MEM-P2U”). The PMS feature is especially useful in helping you to observe any operating sub-band
limits, which apply to your Amateur license class.
1. Store the Lower and Upper tuning/scanning limit
frequencies into the memory pair “MEM-P1L” and
“MEM-P1U”, respectively, or “MEM-P2L” and
“MEM-P2U”. See page 58 for details regarding
memory storage.
2. Press the
[
F
]
button, followed by the
[
SCAN/PMS
]
button.
3. Rotate the
[
DSP/SEL
]
knob to select “PMS-1
PMS2” or “PMS1+2”.
PMS-1: The scanner will be limited within the
frequency range programmed in the
memory pair “MEM-P1L/MEM-P1U”.
PMS-2: The scanner will be limited within the
frequency range programmed in the
memory pair “MEM-P2L/MEM-P2U”.
PMS-1+2: The scanner will be limited within the
frequency ranges programmed by both
memory pairs (“MEM-P1L/MEM-P1U”
and “MEM-P2L/MEM-P2U”).
If a memory pair is vacant, the PMS-1+2 selec-
tion is not available.
4. Press the
[
SCAN/PMS
]
button.
5. Rotate the
[
SQL/RF GAIN
]
knob just to the point
where the noise is silenced and the “ ” indi-
cator on the display turns off.
6. Press the
[
SCAN/PMS
]
key to initiate upward
scanning (toward higher frequencies or higher
memory channel numbers).
7. If you want to change direction of the scan while it
is underway, rotate the
[
MAIN DIAL
]
knob one click
in the opposite direction (in this case, one click
counter-clockwise). You will see the scanner re-
verse direction and scan down in frequency.
You may change the direction of the scanner by
pressing and holding the microphone’s
[
UP
]
/
[
DWN
]
key for one second, if you are using the
MH-31A8J Hand Microphone or optional MD-
100A8X Desktop Microphone.
8. In FM/AM mode, when the scanner encounters a
signal strong enough to open the squelch, the
scanner will halt for five seconds, after which scan-
ning will resume.
In the SSB/CW and SSB-based Data modes,
when the scanner encounters a signal strong
enough to open the squelch, the scanner will step
across the signal very slowly, giving you time to
stop the scan, if you like.
ADVICE:
You may select the manner in which the scanner re-
sumes while it has paused on a signal, using Menu
Item “SCN RES” The default “5Sec” setting will cause
the scanner to resume scanning after five seconds;
you may change it, however, to resume only after the
carrier has dropped out, if you like See page 85.
[
DSP/SEL
]
Knob
[
SCAN/PMS
]
button
[
SQL/RF GAIN
]
Knob
[
MAIN DIAL
]
Knob
[
F
]
button
Page 69FT-450D OPERATION MANUAL
OPERATION ON ALASKA EMERGENCY FREQUENCY: 5167.5 KHZ (U.S. VERSION ONLY)
Section 97.401(d) of the regulations governing amateur radio in the United States permit emergency amateur
communications on the spot frequency of 5167.5 kHz by stations in (or within 92.6 km of) the state of Alaska.
This frequency is only to be used when the immediate safety of human life and/or property are threatened, and
is never to be used for routine communications.
The FT-450D includes the capability for transmission and reception on 5167.5 kHz under such emergency
conditions.
Preparation
1. Press and hold the [F] button for one second to
enter the Menu mode again. The “ ” icon
will appear on the display.
2. Rotate the [DSP/SEL] knob to select the menu
item “EMERGEN”.
3. Press the [DSP/SEL] knob to enable adjustment
of this menu item. The “ ” icon will be blink-
ing.
4. Rotate the [DSP/SEL] knob to select “ON”.
5. Press the [DSP/SEL] knob. The “ ” icon re-
turns to appear continuously.
6. Press and hold the [F] button for one second to
save the new setting and return to normal opera-
tion.
Operation
1. Press the [V/M/MW] button, if necessary, to enter
the Memory mode. A memory channel number will
appear in display.
2. Rotate the [DSP/SEL] knob to select the emer-
gency channel (“MEM-EMG”), which is found be-
tween channels “MEM-P2U” and “US5-001.”
If you partitioned your memory channels into
Memory Groups via Menu Item “MEM GRP”, then
select the memory channel group “M-12-EM”
which is the emergency channel.
3. To exit from emergency channel and return to the
VFO mode, just press the [V/M/MW] button.
Note:
Ì The receive-mode CLARIFIER functions normally
while using this frequency, but variation of the
transmit frequency is not possible. Activation of
“MEM-EMG” or “M-12-EM” does not enable any
other out-of-amateur-band capability on the trans-
ceiver. The full specifications of the FT-450D are
not necessarily guaranteed on this frequency, but
power output and receiver sensitivity should be
fully satisfactory for the purpose of emergency
communication.
Ì In an emergency, note that a half-wave dipole cut
for this frequency should be approximately 45’3”
on each leg (90’6” total length). Emergency op-
eration on 5167.5 kHz is shared with the Alaska-
Fixed Service. This transceiver is not authorized
for operation, under the FCC’s Part 87, for aero-
nautical communications.
[
V/M/MW
]
button
[
DSP/SEL
]
knob
[
HOME/RCL
]
button
[
F
]
button
Page 70 FT-450D OPERATION MANUAL
M
ISCELLANEOUS
S
ETTINGS
DISPLAY SETTINGS
Display Dimmer
You may adjust the brightness level with the five steps.
1. Press the
[
F
]
button, followed by the
[
METER/DIM
]
button to enable adjustment of display dimmer.
2. Rotate the
[
DSP/SEL
]
knob to select a comfort-
able brightness level (1 - 8).
3. Press the
[
METER/DIM
]
button to save the new
setting and return to normal operation.
Display Contrast Level
You may also adjust the contrast level with the 24 steps.
1. Press and hold the
[
F
]
button for one second to
enter the Menu mode. The “ ” icon will ap-
pear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select the menu
item “CONT”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment
of this menu item. The “ ” icon will be blink-
ing.
4. Rotate the
[
DSP/SEL
]
knob to select a desired
contrast level (1 - 24).
You may press the
[
RCL/HOME
]
button to reset
the contrast level to the factory default.
5. Press the
[
DSP/SEL
]
knob. The “ ” icon re-
turns to appear continuously.
6. Press and hold the
[
F
]
button for one second to
save the new setting and return to normal opera-
tion.
[
DSP/SEL
]
Knob
[
METER/DIM
]
button
[
F
]
button
[
DSP/SEL
]
Knob
[
RCL/HOME
]
button
[
F
]
button
Page 71FT-450D OPERATION MANUAL
BEEPER SETTING
Beep Volume
You may adjust the beep volume level via the Menu Item “BEEPVOL”.
1. Press and hold the
[
F
]
button for one second to
enter the Menu mode. The “ ” icon will ap-
pear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select the menu
item “BEEPVOL”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment
of this menu item. The “ ” icon will be blink-
ing.
4. Rotate the
[
DSP/SEL
]
knob to set the desired beep
volume level (FIX 0 - FIX 100).
WARNING! Do not adjust the beep volume too
high. You may press the [METER/DIM] button to
sound a beep as you adjust the
[
DSP/SEL
]
knob.
If you wish to adjust the beep volume level in ac-
cordance with the [AF GAIN] knob, press the
[
F
]
key to change the display to “LNK-XX” then rotate
the
[
DSP/SEL
]
knob to set the volume ratio of the
beep volume level for the receiving audio volume
level. Available selections are “LNK-50” ~ “LNK 0
~ “LNK+50”. When the “LNK 0” is selected, the
beep volume level is the same as receiving audio
volume level.
You may press the [RCL/HOME] button to reset
the beep volume level to the factory default.
5. Press the
[
DSP/SEL
]
knob. The “ ” icon re-
turns to appear continuously.
6. Press and hold the
[
F
]
button for one second to
save the new setting and return to normal opera-
tion.
M
ISCELLANEOUS
S
ETTINGS
[
RCL/HOME
]
button
[
F
]
button
[
DSP/SEL
]
knob
[
METER/DIM
]
button
Page 72 FT-450D OPERATION MANUAL
Beep Tone
You may adjust the beep tone to your desired tone via the Menu Item “BEEPTON”.
1. Press and hold the
[
F
]
button for one second to
enter the Menu mode again. The “ ” icon
will appear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select the menu
item “BEEPTON”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment
of this menu item. The “ ” icon will be blink-
ing.
4. Rotate the
[
DSP/SEL
]
knob to select the desired
tone. Available selections are 440/880/1760 Hz,
factory default: 880 Hz). You may press the
[
METER/DIM
]
button to sound a beep as you ad-
just the
[
DSP/SEL
]
knob.
You may press the
[
RCL/HOME
]
button to reset
the beep tone level to the factory default.
5. Press the
[
DSP/SEL
]
knob. The “ ” icon re-
turns to appear continuously.
6. Press and hold the
[
F
]
button for one second to
save the new setting and return to normal opera-
tion.
BEEPER SETTING
M
ISCELLANEOUS
S
ETTINGS
[
RCL/HOME
]
button
[
F
]
button
[
DSP/SEL
]
knob
[
METER/DIM
]
button
Page 73FT-450D OPERATION MANUAL
AUTOMATIC POWER-OFF
(
APO
)
The “Automatic Power-Off” (APO) feature will turn the radio completely off after a user-defined period of PTT or
key/button inactivity. If you do not press any front panel keys or buttons, rotate the [MAIN DIAL] knob, use the
microphone’s keys and buttons, or transmit, and so long as the transceiver is not scanning or engaged in priority
monitoring, the radio will shut itself off after the specified time period. The available selections for the time before
power-off are 1 - 12 hours (1 hour step), as well as APO Off. This feature is useful in minimizing battery drain in
a mobile installation if you forget to turn the transceiver off.
1. Press and hold the
[
F
]
button for one second to
enter the Menu mode again. The “ ” icon
will appear on the display.
2. Rotate the
[
DSP/SEL
]
knob to select the menu
item “APO”.
3. Press the
[
DSP/SEL
]
knob to enable adjustment
of this menu item. The “ ” icon will be blink-
ing.
4. Rotate the
[
DSP/SEL
]
knob to select desired
“Switch-off” time or “off.”
You may press
[
RCL/HOME
]
button to reset the
APO to the factory default.
5. Press the
[
DSP/SEL
]
knob. The “ ” icon re-
turns to appear continuously.
6. Press and hold the
[
F
]
button for one second to
save the new setting and return to normal opera-
tion.
If there is no action by you within the time interval
programmed, the “APO” notation will blink on the dis-
play and an alert bell will provide an audible warning
from the speaker within one minute of the APO timer
expiration, then the microprocessor will shut down
the radio automatically.
[
DSP/SEL
]
Knob
[
RCL/HOME
]
button
[
F
]
button
M
ISCELLANEOUS
S
ETTINGS
Page 74 FT-450D OPERATION MANUAL
RTTY
(
RADIO TELETYPE
)
O
PERATION
Most RTTY operation today is accomplished using a TNC or other computer-based system that utilizes AFSK
tones. For RTTY operation using a Terminal Unit (TU) or the “FSK” output from a TNC, please see the discus-
sion below. See also the illustration for details regarding connection to your TU.
SETTING UP FOR RTTY OPERATION
Before commencing RTTY operation, please direct
your attention to the setup steps shown in the chart
to the right.
BASIC SETUP
1. Press the
[
MODE
]
/
[
MODE
]
buttons several
times to indicate both the “ ” and “ ” icons
on the display. Engage the RTTY operation us-
ing “LSB” injection, which is generally used in the
Amateur service.
2. When you begin typing on your TU or computer
keyboard, the command to transmit should auto-
matically be sent to the transceiver, causing it to
enter the transmit mode.
NOTE:
If you anticipate making data transmissions of longer
than a few minutes, we recommend that you reduce
the transmitter power to 1/2 ~ 1/3 of its normal maxi-
mum via Menu Item “RFPOWER”.
QUICK POINT:
In the FT-450D, “RTTY” is a mode defined as being
an “FSK” mode, whereby the closing and opening of
a keying line (to ground) causes the Mark/Space tones
to alternate. The RTTY mode is not an AFSK based
mode in this transceiver, and the AFSK output tones
from a TNC will not cause Mark/Space shifting to oc-
cur. Use the “Packet” mode for AFSK-based Baudot
and other data modes.
MENU ITEM
RTY SFT
(
RTTY SHIFT
)
RTY TON
(
RTTY TONE
)
RTYRPOL
(
RTTY RX POLARITY
)
RTYTPOL
(
RTTY TX POLARITY
)
AVAILABLE VALUES
170 / 200 / 425 / 850 Hz
1275 / 2125 Hz
NOR / REV
NOR / REV
ADVICE:
There is no adjustment of the FSK input level
(FSK IN of the DATA jack) on the rear panel;
please make any needed level adjustments at the
TU side.
The Mark/Space Shift utilized in most Amateur
RTTY operation is 170 Hz. Other shifts may be
configured, however, using Menu Item “RTY SFT”.
The FT-450D is set up for “high tone” operation
(centered on 2125 Hz) by default, but you may
configure it for low tone (1275 Hz) operation us-
ing Menu Item “RTY TON”.
You may find that you are unable to decode some
RTTY stations, even if they are of sufficient sig-
nal strength. If this is observed, there may be a
Mark/Space polarity problem between your sta-
tion and the other station. If so, try setting Menu
Item “RTYRPOL” to “REV” (“Reverse”) to see if
that permits copy. A separate Menu Item permits
reversal of your transmitter’s Mark/Space polar-
ity: “RTYTPOL.”
AF
IN PTT
FSK
OUT
F
S
K
I
N
D
A
T
A
O
U
T
D
A
T
A
P
T
T
G
N
D
INPUT
DC 13.8V
22A
ANT
GND
EXT
SPKR
CATLINEARTUNERDATA
TU
N.C.
GND
PTT
FSK OUT
AF IN
N.C.
DATA JACK
DATA IN (Pin 1)
Pin 6
GND (Pin 2)
DATA PTT (Pin 3)
FSK IN (Pin 4)
DATA OUT (Pin 5)
SQL OUT(
)
Page 75FT-450D OPERATION MANUAL
PACKET OPERATION
Packet operation is easily accomplished on the FT-450D by connecting your TNC (Terminal Node Controller) to
the transceiver, per the illustration.
PACKET SETUP
(
INCLUDING SUBCARRIER FREQUENCY
)
Before operation can commence, change Menu Item
D TYPE” setting to “USER-L” (for LSB-Based Packet
Operation) or “USER-U” (for USB-Based Packet Op-
BASIC SETUP
1. Press the
[
MODE
]
/
[
MODE
]
buttons several
times to indicate both the “ ” and “ ” icons
(for LSB-Based Packet) or the “ ” and “
icons (for USB-Based Packet) on the display. En-
gage the Packet operation.
2. When the “transmit” command is received from
the TNC, the transmitter of the FT-450D will au-
tomatically be engaged. Likewise, the command
to return to receive will cause the radio to revert
to the receive mode.
AD VICE:
There is no adjustment of the DATA input level
and DATA output level of the DATA jack on the
rear panel; please make any needed level ad-
justments at the TU side.
During Packet operation via the rear panel’s DATA
jack, the front panel MIC jack is cut off, so you
won’t have a “live microphone” problem during
data operation.
NOTE:
If you anticipate making data transmissions of longer
than a few minutes, we recommend that you reduce
the transmitter power to 1/2 ~ 1/3 of its normal maxi-
mum via Menu Item “RFPOWER”.
QUICK POINT:
DATA Jack Specifications
DATA IN
Input Level: 60 mVp-p
Input Impedance: 600 Ohms
DATA OUT
Fixed level, does not respond to setting of
[
AF GAIN
]
or
[
SQL/RF GAIN
]
knob.
Output Level: 500 mVp-p
Output Impedance: 600 Ohms
DATA
OUT
PTT
DATA
IN
D
A
T
A
I
N
D
A
T
A
O
U
T
D
A
T
A
P
T
T
G
N
D
INPUT
DC 13.8V
22A
ANT
GND
EXT
SPKR
CATLINEARTUNERDATA
TNC
DATA OUT
GND
PAC KET PTT
N.C.
DATA IN
(SQL Control).
DATA JACK
DATA IN (Pin 1)
Pin 6
GND (Pin 2)
DATA PTT (Pin 3)
FSK IN (Pin 4)
DATA OUT (Pin 5)
SQL OUT(
)
eration), to configure your radio for the data mode to
be used.
Page 76 FT-450D OPERATION MANUAL
M
ISCELLANEOUS
AFSK-B
ASED
D
ATA
M
ODES
The FT-450D may also be used for a host of other SSB-based Data modes. Please set up your system using the
illustration as a guideline.
QUICK POINT:
When you have configured Menu Item “DIG VOX” to
select the desired VOX Gain level (1 - 100), the trans-
ceiver will operate in a “VOX” mode, and it is not nec-
essary to connect a PTT line. This makes for very
convenient interfacing to computer Sound Cards, etc.
D
A
T
A
I
N
D
A
T
A
O
U
T
D
A
T
A
P
T
T
G
N
D
INPUT
DC 13.8V
22A
ANT
GND
EXT
SPKR
CATLINEARTUNERDATA
LINE IN or MIC IN
LINE OUT or MIC OUT
COM PORT
Interface
Interface
DATA OUT
GND
PACKET PTT
N.C.
DATA IN
N.C.
DATA JACK
DATA IN (Pin 1)
Pin 6
GND
)
(Pin 2)
DATA PTT (Pin 3)
FSK IN (Pin 4)
DATA OUT (Pin 5)
SQL OUT(
Page 77FT-450D OPERATION MANUAL
M
ISCELLANEOUS
AFSK-B
ASED
D
ATA
M
ODES
NOTE
Page 78 FT-450D OPERATION MANUAL
MENU MODE
The Menu system permits extensive customization of the FT-450D.
You can set up your transceiver to operate just the way you want.
The Menu’s 62 items are grouped into generally used categories from “EXT MNU” to “VOXGAIN”. The Menu
Mode may be set to display all 62 items or the abbreviated set of 16 most often used items.
USING THE MENU
1. Press and hold in the
[
F
]
button for one second.
The Menu Item and a title for the Menu Mode will
appear in the display.
2. Rotate the
[
DSP/SEL
]
knob to select the desired
Menu Item.
3. Press the
[
DSP/SEL
]
knob. The “ ” icon will
appear in the display.
4. Rotate the
[
DSP/SEL
]
knob to change the value
or condition for the Menu Item.
The “ ” icon will blink in the display.
5. Press the
[
DSP/SEL
]
knob. The “ ” icon will
appear in the display
6. Now, hold in the
[
F
]
button for one second to save
the new setting and exit to normal operation.
[
DSP/SEL
]
Knob
Menu Mode Reset
Menu Item or Menu Setting
[
F
]
Button
You may reset all the Menu settings to their
original factory defaults.
1. Turn the front panel
[
POWER
]
Button off.
2. While holding in
[
F
]
button, press the
[
POWER
]
Button to turn the transceiver
on.
[
POWER
]
Button
[
F
]
Button
MENU FUNCTION AVAILABLE VALUES DEFAULT SETTING
EXT MNU (EXTENSION MENU) ON / OFF ON
A&FDIAL (AM&FM DIAL) DISABLE / ENABLE DISABLE
APO (APO TIME) OFF / 1 ~ 12 (h) OFF
BCN TIM (BEACON TIME) OFF / 1 ~ 255 (sec) OFF
BCN TXT (BEACON TEXT) - -
BEEPTON (BEEP TONE) 440 / 880 / 1760 (Hz) 880Hz
BEEPVOL FIX0 ~ FIX100 or LNK-50 ~ LNK0 ~ LNK+50 FIX10 or LNK-8
CAT RTS DISABLE / ENABLE ENABLE
CAT TOT (CAT TIME OUT TIME) 10 / 100 / 1000 / 3000 (mSec) 10
CATRATE 4800 / 9600 / 19200 / 38400 (bps)/DATA 4800
CLAR (CLAR DIAL / SEL) DIAL / SEL DIAL
CLK SFT (CLOCK SHIFT) ON / OFF OFF
CONT (DISP CONTRAST) 1 ~ 24 10
CW AUTO (CW AUTO MODE) ON / OFF OFF
CW BFO USB / LSB / AUTO USB
CW DLY (CW DELAY) FULL / 30 ~ 3000 (mSec) 250
CW KEY (CW KEY REV) NOR / REV NOR
CW QSK 15 / 20 / 25 / 30 (mSec) 15
CWPADDL (CW PADDLE) KEY / MIC KEY
CWPITCH 400 / 500 / 600 / 700 / 800 (Hz) 700
Page 79FT-450D OPERATION MANUAL
MENU MODE
MENU FUNCTION AVAILABLE VALUES DEFAULT SETTING
CWSPEED 4 wpm (20cpm) ~ 60 wpm (300cpm) 12wpm (60cpm)
CWSTONE (CW SIDE TONE) FIX0 ~ FIX100 or LNK-50 ~ LNK0 ~ LNK+50 FIX10 or LNK-8
CWTRAIN (CW TRAINING) N: / A: / M: N:
CWWEIGT (CW WEIGHT) 1/2.5 ~ 1/4.5 1/3.0
D DISP (DATA DISP) -3000 ~ 0 ~ +3000 (Hz) 0
D TYPE (DTAT MODE) RTTY / USER-L / USER-U RTTY
DIALSTP (DIAL STEP) SSB/CW:1/10/20 (Hz), AM/FM:100/200 (Hz)
SSB/CW:10,AM/FM:100
DIG VOX OFF / 1 ~ 100 OFF
EMERGEN (EMERGENCY) ON / OFF OFF
KEYHOLD (KEY HOLD TIME) 0.5 / 1.0 / 1.5 / 2.0 1.0
LOCKMOD (LOCK MODE) FREQ / PANEL / ALL FREQ
M-TUNE ON / OFF ON
MEM GRP (MEMORY GROUP) ON / OFF OFF
MEM TAG TAG-OFF / TAGNAME TAG-OFF
MIC EQ 0 ~ 9 0
MICGAIN LOW / NOR / HIGH NOR
MICSCAN (MIC AUTO SCAN) ON / OFF ON
MY BAND ON / OFF ON
MY MODE ON / OFF ON
P M-DWN (MIC-DWN PG) One of 52 functions (See page 16) DWN
P M-FST (MIC-FAST PG) One of 52 functions (See page 16) FAST
P M-UP (MIC-UP PG) One of 52 functions (See page 16) UP
PEAKHLD (METER PEAK HOLD ) ON / OFF ON
PNL-C.S (PANEL’S CUSTOM SWITCH) One of 52 functions (See page 16) VCC
QSPL F (QUICK SPLIT FREQ) -20 ~ 0 ~ +20(KHz) +5
RFPOWER (RF PWR SET) 5 ~ 100 100
RPT (REPEATER SHIFT DIRECTION) - SHIFT / SIMPLEX / +SHIFT SIMPLEX
RPT SFT (REPEATER SHIFT OFFSET) 0 ~ 9.99
RTY SFT (RTTY-SHIFT) 170 / 200 / 425 / 850 170
RTY TON (RTTY-TONE) 1275 / 2125 (Hz) 2125
RTYRPOL (RTTY-RX-POLARITY) NOR / REV NOR
RTYTPOL (RTTY-TX-POLARITY) NOR / REV NOR
SCN RES (SCAN RESUME) BUSY / TIME 1 ~ 10 TIME5
SELDIAL (SEL DIAL MODE) CWSTONE / CWSPEED / 100KHz /1MHz
100KHZ
/ MICGAIN / RFPOWER
SQL TYP (SQL TYPE) OFF / ENC / ENC DEC OFF
SQL/RFG (SQL/RF GAIN) SQL / RF GAIN RF GAIN
STBY BP (STBY BEEP) ON / OFF OFF
TONE F (TONE FREQ) 67 ~ 254.1 (Hz) 88.5 (Hz)
TOT (TOT TIME) OFF/1 ~ 20 (Min) OFF
TUNER (TUNER/ATAS) ATAS / EXT ATU / INT ATU
/ INTRATU / F TRANS
INT ATU
VOX DLY (VOX DELAY) 100 ~ 3000 (ms) 500 (ms)
VOXGAIN 1 ~ 100 50
: Depends on the transcever’s version
Page 80 FT-450D OPERATION MANUAL
EXT MNU (EXTENSION MENU)
Function: Enables / Disables the extended Menu
Mode
Available Values: ON / OFF
Default: ON
OFF: The menu will only display the 16 most often
used items.
ON: All 62 menu mode items will be displayed.
A&FDIAL (AM&FM DIAL)
Function: Enables or disables the
[
MAIN DIAL
]
knob
in the AMand FM modes.
Available Values: ENABLE / DISABLE
Default: DISABLE
ENABLE: The frequency can be set with the
[
MAIN
DIAL
]
knob even in the AM/FM mode.
DISABLE: The
[
MAIN DIAL
]
knob does not change
the frequency in the AM / FM mode.
APO (APO TIME)
Function: OFF / 1~12 (h)
Available Values: ON / OFF
Default: OFF
Selects the Auto Power Off time (time before power
goes off).
BCN TIM (BEACON TIME)
Function: Selects the interval time (between mes-
sage and message)
Available Values: OFF/1~255 (sec)
Default: OFF
BCN TXT (BEACON TEXT)
Function: Stores the message for the Beacon. Up
to 118 characters may be stored.
Please refer to page 52 for storage procedure.
BEEPTON (BEEP TONE)
Function: Selects the beep frequency.
Available Values: 440 / 880 / 1760 (Hz)
Default: 880 (Hz)
BEEPVOL
Function: Selects the beep volume level.
Available Values: FIX0 ~ FIX100 or
LNK-50 ~ LNK 0 ~ LNK+50
Default: FIX10 or LNK-8
CAT RTS
Function: Enables / Disables the RTS port of the
CAT jack.
Available Values: DISABLE/ENABLE
Default: ENABLE
CAT TOT (CAT TIME OUT TIME)
Function: Sets the Time-Out Timer countdown time
for a CAT command input.
Available Values: 10 / 100 /1000 / 3000 (ms)
Default: 10
The Time-Out Timer shuts off the CAT data input af-
ter a continuous transmission of the programmed
time.
CATRATE
Function: Sets the transceiver circuitry for the CAT
baud rate to be used.
Available Values: 4800/9600/19200/38400 (bps)/
DATA
Default: 4800
The CAT baud rate is set for the transceiver.
Setting “CATRATE” to “DATA” will enable RTTY op-
eration from the CAT jack. The interconnection for
RTTY operation is shown below.
MENU MODE
P
i
n
3
:
S
E
R
I
A
L
I
N
(
F
S
K
I
N
)
E
X
T
S
P
(
F
S
K
O
U
T
)
P
i
n
7
:
R
T
S
(
D
A
T
A
P
T
T
)
Requires the RTTY Software
(Not Supplied)
L
I
N
E
I
N
J
a
c
k
R
S
-
2
3
2
S
J
a
c
k
P
i
n
5
:
G
N
D
INPUT
DC 13.8V
22A
ANT
GND
EXT
SPKR
CATLINEARTUNERDATA
Page 81FT-450D OPERATION MANUAL
CLAR (CLAR DIAL/SEL)
Function: Setting of CLAR button
Available Values: DIAL / SEL
Default: DIAL
Defines which Control knob is used for setting the
clarifier-offset frequency.
CLK SFT (CLOCK SHIFT)
Function: Shifting of CPU clock frequency
Available Values: ON / OFF
Default: OFF
This function is only used to move a spurious re-
sponse “birdie,” should it fall on a desired frequency.
CONT (DISP CONTRAST)
Function: Display contrast adjustment
Available Values: 1~24
Default: 10
The display contrast level is set 1~24
CW AUTO (CW AUTO MODE)
Function: Enables the KEY jack, to permit CW op-
eration while in SSB modes.
Available Values: OFF / ON
Default: OFF
OFF: The KEY jack is enabled in CW mode only.
ON: The KEY jack is enabled on all modes (SSB
mode: A1A). Thus, on SSB, you can ask a sta-
tion for a CW QSO without having to change
your FT-450’s Mode selection, if Menu “CW
AUTO” is set to “ON.”
CW BFO
Function: Sets the CW carrier oscillator injection
side in CW mode
Available Values: USB / LSB / AUTO
Default: USB
USB: Injects the CW carrier oscillator on the USB
side
LSB: Injects the CW carrier oscillator on the LSB
side
AUTO: Injects the CW carrier oscillator on the LSB
side while operating on the 7 MHz band and
below, USB side while operating on the 10
MHz band and up.
CW DLY (CW DELAY)
Function: Sets the receiver recovery time during
pseudo-VOX CW semi-break-in opera-
tion.
Available Values: FULL / 30~3000ms
Default: 250
The recovery time may be adjusted in steps of 10
msec. A longer delay may be preferable if you pause
frequently while sending.
CW KEY (CW KEY REV)
Function: Sets the keyer paddle's wiring configura-
tion.
Available Values: NOR / REV
Default: NOR
The polarity can be reversed in the menu without
changing the connection of the keyer when there is a
left-handed operator or, two or more people.
NOR(NORMAL): Keyer paddle polarity is normal.
The plug “Tip” connection pro-
duces dots, and the plug "ring" con-
nection produces dashes.
REV(REVERSE): Keyer paddle polarity is inverted.
The plug “Tip” connection pro-
duces dashes, and the “Ring” con-
nection produces dots.
CW QSK
Function: Selects the time delay between when the
key is closed and the carrier is transmit-
ted during QSK operation when using the
internal keyer.
Available Values: 15 / 20 / 25 / 30 (ms)
Default: 15 (ms)
Note:
If you select “25 ms” or “30 ms,” please do not at-
tempt to set Menu “CW SPEED” to a speed faster than
50 wpm (250 cpm), as the delay will make it impos-
sible to transmit.
CWPADDL (CW PADDLE)
Function: When enabled, the microphone’s (MH-
31A8J)
[
UP
]
/
[
DWN
]
keys may be used for
CW keying.
Available Values: KEY / MIC
Default: KEY
KEY: The key connected to KEY Jack is selected.
MIC: When this Menu Item is set to “MIC,” the
microphone’s (MH-31A8J)
[
UP
]
/
[
DWN
]
keys
may be used for CW keying. (while the built-in
electronic keyer is engaged).
CWPITCH
Function: Sets the pitch of the CW sidetone, (BFO
offset) and the CW filter center frequen-
cies.
Available Values: 400 / 500 / 600 / 700 / 800 (Hz)
Default: 700
The CW pitch may be adjusted in steps of 100 Hz.
MENU MODE
Page 82 FT-450D OPERATION MANUAL
CWSPEED
Function: Sets the sending speed for the built-in
Electronic keyer.
Available Values: 4 wpm(20cpm)~60wpm(300cpm)
Default: 12wpm (60cpm)
You can set the sending speed in either: wpm (words
per minute), or cpm (characters per minute).
To button between “Wpm” and “cpm”, just press the
[
F
]
button.
Note:
If the CW QSK is set to 25ms, the setting of CW
SPEED must not exceed 50wpm (250cpm); And if
the CW QSK is set to 30ms, the setting of CW SPEED
must not exceed 42wpm (210cpm). The delay will
make it impossible to transmit.
CWSTONE (CW SIDE TONE)
Function: Sets the CW sidetone volume level.
Available Values: FIX0 ~ FIX100 or
LNK-50 ~ LNK 0 ~ LNK+50
Default: FIX10 or LNK-8
CWTRAIN (CW TRAINING)
Function: Setting of CW training function
Available Values: N: / A: / M:
Default: N:
Sends random Morse Code five-character groups via
the sidetone.
N: Numeric characters only
A: Alphabet characters only
M: Numeric and Alphabet characters (Mixed)
CWWEIGT (CW WEIGHT)
Function: Sets the CW weight level.
Available Values: 1/2.5~1/4.5
Default: 1/3.0
Sets the Dot/Dash ratio for the built-in electronic keyer.
D DISP (DATA DISP)
Function: DIG (USER-L or USER-U) mode opera-
tion.
Available Values: -3000Hz ~ 0 ~ +3000Hz
Default: 0
Defines the displayed frequency offset during DATA
(USER-L or USER-U) mode operation.
D TYPE (DTAT MODE)
Function: Selects the mode and sideband (if appli-
cable) in the DATA mode.
Available Values: RTTY/USR-L/USR-U
Default: RTTY
RTTY: FSK RTTY operation
USR-L: User-programmed custom operation based
on LSB mode
USR-U: User-programmed custom operation based
on USB mode
DIALSTP (DIAL STEP)
Function: Sets the DIAL knob's tuning speed.
Available Values: SSB/CW: 1 / 10 / 20 (Hz)
AM/FM: 100 / 200 (Hz)
Default: SSB/CW: 10 (Hz), AM/FM: 100 (Hz)
The width of the step of the
[
MAIN DIAL
]
knob can
be set for each mode.
DIG VOX
Function: Sets the gain of the VOX circuitry input
level for the DIG mode.
Available Values: OFF / 1~100
Default: OFF
EMERGEN (EMERGENCY)
Function: Enables Tx/Rx operation on the Alaska
Emergency Channel, 5167.5 kHz.
Available Values: ON/OFF
Default: OFF
When this Menu Item is set to “ON,” the spot fre-
quency of 5167.5 kHz will be enabled. To get to this
frequency, use the
[
DSP/SEL
]
knob to navigate. The
Alaska Emergency Channel will be found between
the Memory channel “US5-001” and “MEM-500.”
NOTE:
Use of this frequency is restricted to amateurs oper-
ating in (or within 92.6 km of) the U.S. State of Alaska,
and it is to be used for emergency communications
only (involving the immediate protection of life or prop-
erty).
KEYHOLD (KEY HOLD TIME)
Function: Sets the hold time for a push button to
activate.
Available Values: 0.5 / 1.0 / 1.5 / 2.0
Default: 1.0
MENU MODE
Page 83FT-450D OPERATION MANUAL
LOCKMOD (LOCK MODE)
Function: Sets the keylock for the panel buttones
and dial
Available Values: FREQ / PANEL / ALL
Default: FREQ
Selects the operation of the front panel’s
[
LOCK
]
key.
FREQ: Locks the front panel keys and knobs related
to frequency control.
Front Panel:
[
A=B
]
button,
[
FAST
]
button,
[
BAND
]
button,
[
A/B
]
button,
[
MW
]
button
[
V/M
]
button,
[
HOME
]
button,
[
RCL
]
button,
[
STO
]
button,
[
SPLIT
]
button,
[
PMS
]
button,
[
SCN
]
button,
[
MAIN DIAL
]
knob,
[
DSP/SEL
]
knob (Turns or
Pushes).
[
C.S
]
button:
QSPL, DWN, FAST, UP
Microphone:
MH-31A8J (or optional MH-36E8J, MD-100A8X and
MD-200A8X):
[
UP
]
key,
[
DWN
]
key,
[
FAST
]
key
ALL: Locks all front panel keys and knobs (except
POWER and LOCK keys) and microphone keys.
Front Panel:
[
DSP
]
button,
[
PROC/KEYER
]
button,
[
IPO/ATT
]
button,
[
AGC
]
button, [MODE
]
but-
ton,
[
NB
]
button,
[
CLAR
]
button,
[
A=B
]
button,
[
FAST
]
button,
[
BAND
]
button,
[
A/B
]
button,
[
HOME
]
button,
[
RCL
]
button,
[
VOX
]
button,
[
STO
]
button,
[
STEP
]
button,
[
SPLIT
]
button,
[
MW
]
button,
[
V/M
]
button,
[
PMS
]
button,
[
SCAN
]
button,
[
MAIN DIAL
]
knob,
[
DSP/SEL
]
knob (Turns or Pushes) (
[
CLAR]
knob)
[
C/S
]
button:
MONI, N/A, P/B, PLAY1, PLAY2, PLAY3, QSPL,
SWR, VCC, DWN, FAST, UP
Microphone:
MH-31A8J (or optional MH-36E8J, MD-100A8X and
MD-200A8X):
[
UP
]
key,
[
DWN
]
key,
[
FAST
]
key
MENU MODE
PANEL: Locks all front panel keys and knobs.
[
DSP
]
button,
[
PROC/KEYER
]
button,
[
IPO/ATT
]
button,
[
AGC
]
button,
[
MODE
]
but-
ton,
[
NB
]
button,
[
CLAR
]
button,
[
A=B
]
button,
[
FAST
]
button,
[
BAND
]
button,
[
A/B
]
button,
[
HOME
]
button,
[
RCL
]
button,
[
VOX
]
button,
[
STO
]
button,
[
STEP
]
button,
[
SPLIT
]
button,
[
MW
]
button,
[
V/M] button,
[
PMS
]
button,
[
SCAN
]
button,
[
MAIN DIAL
]
knob,
[
DSP/SEL
]
knob (Turns or Pushes),
[
METER
]
button
M-TUNE
Function: Permission/non-permission of Memory
tune
Available Values: ON / OFF
Default: ON
ON: Forwarding from the memory channel and the
home channel to VFO is permitted.
OFF: Forwarding from the memory channel and the
home channel to VFO is not permitted.
In the “Memory Tune” mode, you may freely tune off
of the memory channel. This is similar to VFO opera-
tion. Memory Tune operation will not alter the con-
tents of the memory channel, so long as you do not
over-write the contents of the current memory.
MEM GRP (MEMORY GROUP)
Function: Enables/disables the memory grouping
feature.
Available Values: ON / OFF
Default: OFF
When this Menu Item is set to “ON,” the 500 “stan-
dard” memory channels are partitioned into ten
Memory Groups, each holding up to 50 memory chan-
nels.
MEM TAG
Function: Stores Alpha-Numeric “Tags” for the
memory channels.
See page 62 for information on setting the “Memory
Tags”.
Page 84 FT-450D OPERATION MANUAL
MIC EQ
Function: Setting of the DSP microphone equalizer
Available Values: 0 ~ 9
Default: 0
You may select one of ten available DSP equaliza-
tion techniques for transmitted microphone audio.
0: Flat
1: Low-frequency component is decreased.
2: Mid-frequency component is decreased.
3: High-frequency component is decreased.
4: High-frequency component is enhanced.
5: Mid-frequency component is enhanced.
6: Low-frequency component is enhanced.
7: Low-frequency component is enhanced and High-
frequency component is decreased.
8: Low-frequency component is decreased and Mid-
frequency component is enhanced.
9: Low-frequency component is decreased and High-
frequency component is enhanced.
MICGAIN
Function: Setting of the MIC gain
Available Values: LOW / NOR / HIGH
Default: NOR
Adjusts the microphone gain level for SSB/AM/FM.
LOW: When the microphone input is high the speech
processor is turned off automatically.
NOR: For normal voice the speech processor is
turned on automatically.
HIGH: When the microphone input is low the speech
processor is turned on automatically.
MICSCAN (MIC AUTO SCAN)
Function: “ON/OFF” of microphone scanning func-
tion
Available Values: ON/OFF
Default: ON
Enables/disables scanning access via the
microphone’s
[
UP
]
/
[
DWN
]
keys.
OFF: The frequency or the memory channel is
scanned only while
[
UP
]
/
[
DWN
]
button is be-
ing pushed. The scanning stops when
[
UP
]
/
[
DWN
]
button is released.
ON: When
[
UP
]
/
[
DWN
]
button is held for about 1.0
second, the scanning continues even after the
button is released.
MY BAND
Function: Setting of the my band
Available Values: ON/OFF
Default: ON
The “My Bands” feature allows you to select several
Amateur bands, and make only those bands avail-
able for selection via the
[
BAND
]
/
[
BAND
]
but-
tons.
ON: Only the bands that are turned on will be shown
when pushing the
[
BAND
]
/
[
BAND
]
button.
OFF: A Band that is turned off will not appear when
the
[
BAND
]
/
[
BAND
]
button is pushed.
NOTE:
The band presently in use and the General band can-
not be turned off.
MY MODE
Function: Setting of my mode
Available Values: ON/OFF
Default: ON
The “My Mode” feature allows you to select an oper-
ating mode, and set whether or not the mode will be
displayed or skipped when the
[
MODE
]
/
[
MODE
]
buttons are pressed.
This feature can be very useful in HF operation, when
the AM/FM/DATA modes are not used.
ON: Only the mode registered by turning on can be
selected by pushing
[
MODE
]
/
[
MODE
]
button.
OFF: A mode that is turned off will not be appear
when pressing the
[
MODE
]
/
[
MODE
]
but-
ton.
NOTE:
The mode displayed on the display while setting “My
mode” cannot be turned off.
P M-DWN (MIC-DWN PG)
Function: One of 52 functions can be preset and
assigned to the
[
DWN
]
key of the microphone.
Available Values: Please see page 16.
Default: DOWN
Presets of various functions can be assigned to the
[
DWN
]
key of the microphone using this option.
P M-FST (MIC-FAST PG)
Function: One of 52 functions can be preset and
assigned to the
[
FST
]
key of the microphone.
Available Values: Please see page 16.
Default: FAST
Presets of various functions can be assigned to the
[
FAST
]
key of the microphone using this option.
MENU MODE
Page 85FT-450D OPERATION MANUAL
P M-UP (MIC-UP PG)
Function: One of 52 functions can be preset and
assigned to the
[
UP
]
key of the micro-
phone.
Available Values: Please see page 16.
Default: UP
Presets of various functions can be assigned to the
[
UP
]
key of the microphone using this option.
PEAKHLD (METER PEAK HOLD )
Function: Peak hold setting of S meter.
Available Values: ON/OFF
Default: ON
When this function is set to on the peak S meter read-
ing is held for one second to improve readability.
PNL-C.S
Function: One of 52 functions can be preset and as-
signed to the
[
VOICE/C.S
]
key.
Available Values: Please see page 16.
Default: VCC
Presets of various functions can be assigned to the
[
VOICE/C.S
]
key using this option.
Please see page 16 for a detailed explanation.
QSPL F (QUICK SPLIT FREQ)
Function: offsets the transmit frequency.
Available Values: -20 ~ 0 ~ +20 (kHz)
in 1kHz increments
Default: +5
The Quick Split feature allows you to set a one-touch
offset to be applied to your radio's transmit frequency
compared to the receiving frequency. Also, the trans-
mit mode is set to the same mode as the receive
frequency (See page 43).
RFPOWER (RF PWR SET)
Function: Sets the maximums transmit power level
for the current band.
Available Values: 5 ~ 100 (W)
Default: 100 (W)
RPT (REPEATER SHIFT DIRECTION)
Function: Sets the Repeater shift Direction
Available Values: -SHIFT / SIMPLEX / +SHIFT
Default: SIMPLEX
RPT SFT (REPEATER SHIFT OFFSET)
Function: Sets the magnitude of the repeater shift
on the 28/50MHz band.
Available Values: 0.00 ~ 99.99 (MHz)
Default: Depends on the transcever’s version.
The FT-450D may be utilized on 29 MHz and 50 MHz
repeaters.
ADVICE:
The conventional repeater shift used on 29 MHz is
100 kHz, while on the 50 MHz band the shift may
vary between 500 kHz and 1.7 MHz (or more). To
program the proper repeater shift, use Menu Item
RPT SFT” (see page 55).
RTY SFT (RTTY-SHIFT)
Function: Selects the frequency shift for FSK RTTY
operation.
Available Values: 170 / 200 / 425 / 850 (Hz)
Default: 170
RTY TON (RTTY-TONE)
Function: Selects the Mark tone for RTTY opera-
tion.
Available Values: 1275 / 2125 (Hz)
Default: 2125
RTYRPOL (RTTY-RX-POLARITY)
Function: Selects normal or reverse Mark / Space
polarity for RTTY receive operation.
Available Values: NOR/REV
Default: NOR
RTYTPOL (RTTY-TX-POLARITY)
Function: Selects normal or reverse Mark / Space
polarity for RTTY transmit operation.
Available Values: NOR /REV
Default: NOR
SCN RES (SCAN RESUME)
Function: Sets the delay time for scan resume.
Available Values: BUSY / TIME1 ~ 10 (sec)
Default: TIME5 (sec)
SELDIAL (SEL DIAL MODE)
Function: Assigns a second function to DSP/SEL
knob that is activated when the DSP/SEL
knob is momentarily depressed.
Available Values: CWSTONE / CWSPEED
/ 100KHZ /1MHZ/MICGAIN
/ RFPOWER
Default: 100KHZ (100 kHz)
CWSTONE: CW SIDETONE LEVEL
CWSPEED: CW KEYER SPEED
100KHZ: 100KHz Step
1MHZ: 1MHz Step
MICGAIN: MIC GAIN SET
RFPOWER: RF POWER SET
SQL TYP (SQL TYPE)
Function: Selects the Tone Encoder and/or Decoder
mode.
Available Values: OFF / ENC / ENC/DEC
Default: OFF
OFF: The function of “SQL knob” that exists in
the front panel is selected.
ENC: CTCSS Encoder
ENC/DEC: CTCSS Encoder/Decoder(Tone Squelch)
SQL/RFG (SQL/RF GAIN)
Function: Selects the configuration of the front
panel’s SQL/RF knob.
Function: SQL/RF-GAIN
Default: SQL
MENU MODE
Page 86 FT-450D OPERATION MANUAL
STBY BP (STBY BEEP)
Function: Setting of standby beep
Available Values: OFF / ON
Default: OFF
OFF: No beep sound is transmitted.
ON: A beep is transmitted before returning to
receive.
The beep, transmitted when the PTT is released, will
inform the other operators that your transmission has
ended.
TONE F (TONE FREQ)
Function: Sets the CTCSS Tone Frequency.
Available Values: 67.0 ~ 254.1 (Hz)
50 Standard CTCSS tones
Default: 88.5 (Hz)
TOT (TOT TIME)
Function: Selects the time of the Time-Out-Timer.
Available Values: OFF/1 ~ 20 (min)
Default: OFF
MENU MODE
TUNER (TUNER/ATAS)
Function: Setting of the Auto Antenna and Antenna
Tuner
Available Values: ATAS / EXT ATU / INT ATU
/ INTRATU / F RANS
Default: INT ATU
Selects the device (FC-40 or ATAS-100/-120/-120A)
controlled by the front panel’s
[
TUNE
]
button.
ATAS: The
[
TUNE
]
button will activate the op-
tional ATAS-100/-120/-120A on the HF
amateur bands and 50 MHz amateur
band.
EXT ATU: The
[
TUNE
]
button will activate the op-
tional FC-40.
INT ATU: The
[
TUNE
]
button will activate the An-
tenna Tuner. The tuner passes only the
Transmitter RF.
INTRATU: The
[
TUNE
]
button will activate the An-
tenna Tuner. The tuner passes both the
Transmitter RF and the Receiver signal.
F TRANS: The frequency data of the radio is sent to
another FT-450D. This feature is very
usefll for the “SO2R” (Single Operator,
Two Radio) operation. In this case, the in-
terconnection is as follows.
INPUT
DC 13.8V
22A
ANT
GND
EXT
SPKR
CATLINEARTUNERDATA
INPUT
DC 13.8V
22A
ANT
GND
EXT
SPKR
CATLINEARTUNERDATA
T
U
N
E
R
C
A
T
Junction Connector
Dsub 9pin to Dsub 9pin
Cross CableCT-62
MASTER SETTING
Set menu itme “TUNER” to “F TRANS”.
SLAVE TRANSCEIVER SETTING
Set menu itme “CAT RTS” to “DISABLE”.
Set menu itme “CATRATE” to “4800 bps”.
OPERA TION
When the
[
TUNE
]
button on the Master Transceiver is pressed, the
Slave Transceiver frequency becomes the same as the Master Trans-
ceiver.
IMPORTANT NOTICE
Please install an antenna protection circuit so the Master (RX) Trans-
ceiver is not damaged when the Slave (TX) Transceiver is transmitting.
Page 87FT-450D OPERATION MANUAL
MENU MODE
VOX DLY (VOX DELAY)
Function: Sets the “hang time” for the VOX circuitry.
Available Values: 100 ~ 3000 (ms) (100 ms/step)
Default: 500 (ms)
In VOX operation, sets the delay time when the trans-
mitter will return to receive after a voice pause.
The Delay time can be set while transmitting.
VOXGAIN
Function: Sets the gain of the VOX circuitry's input
audio detector.
Available Values: 1 ~ 100
Default: 50
The sensitivity is least at “1”, and maximum at “100”.
The VOX operation sensitivity can be set while trans-
mitting.
Page 88 FT-450D OPERATION MANUAL
CLONING
You can transfer all data stored in one transceiver to another set by utilizing the handy “Cloning” feature. This
requires a user supplied cloning cable, which connects the CAT jacks on the two transceivers, as shown below.
To clone from one transceiver to another, use the following procedure:
1. Insert the D-SUB 9pin cross cable (User Supplied)
into the CAT jack of each transceiver.
2. Turn both transceivers off, then press and hold in
the
[
MODE
]
and
[
MODE
]
buttons on each ra-
dio while turning the power on again. The “cLonE
C.S-SND” notation will appear on the display.
3. On the “Source” radio, press the
[
C.S/VOICE
]
but-
ton.
4. Data will now be transferred to the “Destination”
radio from the “Source” radio.
When the clone completes successfully, “CLonE
SENDING” is displayed on the display.
If there is a problem during the cloning process,
Error” will be displayed. Check your cable con-
nections and try again.
5. If cloning is successful, turn the “Destination” ra-
dio off, and “cLonE C.S-SND” notation will reappear
on the “Source” radio.
6. Turn the “Source” radio off.
7. Remove the clone cable. The channel and oper-
ating data for both radios are now identical. Both
radios may be turned on now for normal opera-
tion.
NOTE:
The cloning operation cannot be performed between
the FT-450D and FT-450.
INPUT
DC 13.8V
22A
ANT
GND
EXT
SPKR
CATLINEARTUNERDATA
INPUT
DC 13.8V
22A
ANT
GND
EXT
SPKR
CATLINEARTUNERDATA
D-SUB 9pin cross cable (User Supplied)
[
C.S/VOICE
]
button
“Destination”
“Source” Press the [C.S/VOICE] button
[MODE] and [MODE] buttons
[
ON/OFF
]
button
Page 89FT-450D OPERATION MANUAL
N
OTE
Page 90 FT-450D OPERATION MANUAL
I
NSTALLATION
OF
O
PTIONAL
A
CCESSORIES
AUTOMATIC-MATCHING 200-MEMORY ANTENNA TUNER FC-40 OPERATION
The FC-40 makes use of the control circuitry built into the transceiver, which allows the operator to control and
monitor automatic operation of the FC-40, which mounts near the antenna feedpoint. The FC-40 uses specially
selected, thermally-stable components, and is housed in a waterproof case to withstand severe environmental
conditions with high reliability.
A carefully-chosen combination of solid-state switching components and high-speed relays allows the FC-40 to
match a wide variety of antennas to within a 2:1 SWR on any amateur band frequency (160 through 6 meters),
typically in less than eight seconds. Transmitter power required for matching may be as little as 4 - 60 Watts, and
matching settings are automatically stored in memory for instant recall when the same frequency range is
selected later.
Please see the manual of FC-40 for detailed information.
Interconnections to FT-450D
After mounting the FC-40, connect the cables from the tuner to the ANT and TUNER jacks on the rear panel of
the FT-450D Transceiver.
Installation
The optional FC-40 Automatic Antenna Tuner provides automatic tuning of a coaxial line so as to present a
nominal 50-ohm impedance to the FT-450D’s, HF/50 MHz antenna port.
Before operation can begin, you must instruct the FT-450D’s microprocessor that the FC-40 is being used. This
is done using the Menu Mode:
1. Press and hold the
[
F
]
button for one second to
enter the Menu Mode.
The “ ” icon will appear in the display.
2. Rotate the
[
DSP/SEL
]
knob to select the Menu
Item “TUNER.”
3. Press the
[
DSP/SEL
]
knob to enable this selected
Menu Item.
4. Rotate the
[
DSP/SEL
]
knob to change the setting
to “EXT ATU.”
5. Press and hold the
[
F
]
button for one second to
return to normal operation.
[
DSP/SEL
]
Knob
[
F
]
button
INPUT
DC 13.8V
22A
ANT
GND
EXT
SPKR
CATLINEARTUNERDATA
Instal supplied ferrite
core as close to con-
nector as possible. Control Cable (5 m)
Coaxial Cable (5 m)
Antenna Terminal
GND
Wrap the ends of the wa-
terproof cap with supplied
sealing tape to protect
against moisture ingress.
FT-450D
FC-40
Page 91FT-450D OPERATION MANUAL
I
NSTALLATION
OF
O
PTIONAL
A
CCESSORIES
Operation
1. Press the
[
TUNE
]
button briefly to activate the
Automatic Antenna Tuner.
The “
” icon will appear in the display.
If the transceiver frequency is out of the amateur
band, the “ ” icon will not appear.
2. Press and hold the
[
TUNE
]
button for one second
to begin automatic tuning. The transmitter will be
engaged, and the “ ” icon will blink while tun-
ing is in progress.
3. Tuning will stop automatically when a low SWR is
achieved. You may Press and hold the
[
TUNE
]
button for one second while tuning is in progress,
to cancel the automatic tuning.
4. To disable the Automatic Antenna Tuner, press
the [TUNE] button briefly again.
AUTOMATIC-MATCHING 200-MEMORY ANTENNA TUNER FC-40 OPERATION
Note
Ì Please connect a good earth ground to the GND terminal of FC-40.
Ì The carrier signal transmits continuously while tuning is in progress. Please monitor the operating frequency
before beginning the tuning process. Be sure you are not interfering with others who may already be using
the frequency.
Ì It is normal to hear the sound of the relays while tuning is in progress.
Ì If the impedance cannot be matched by the FC-40 better than 2:1, and the “ ” icon will blink, the micropro-
cessor will not retain the tuning data for that frequency, as the FC-40 presumes that you will want to adjust or
repair your antenna system to correct the high SWR condition.
[
TUNE
]
button
Page 92 FT-450D OPERATION MANUAL
I
NSTALLATION
OF
O
PTIONAL
A
CCESSORIES
ACTIVE-TUNING ANTENNA SYSTEM
(
ATAS-100/-120/120A
)
OPERATION
The optional ATAS-100, ATAS-120, or ATAS-120A Active-Tuning Antenna System permits operation on a num-
ber of HF bands (7/14/21/28 MHz) plus 50 MHz.
The FT-450D provides microprocessor control of the tuning mechanism in the ATAS antenna for convenient
automatic tuning.
Interconnections to FT-450D
“ATAS-120A” is connected referring to the figure below.
ADVICE:
Always turn off the power switch on the FT-450D and the external power supply before you connect any cables.
ATTENTION:
Ì Do not touch the cables or connectors with wet hands.
Ì Do not touch the cables or connectors when you transmit. There is danger of electric shock or other serious
injury.
Installation
Before operation can begin, you must instruct the FT-450D’s microprocessor that the ATAS-100/-120/-120A is
being used. This is done using the Menu Mode:
1. Press and hold the
[
F
]
button for one second to
enter the Menu Mode.
The “ ” icon will appear in the display.
2. Rotate the
[
DSP/SEL
]
knob to select the Menu
Item “TUNER”.
3. Press the
[
DSP/SEL
]
knob to enable this selected
Menu Item.
4. Rotate the
[
DSP/SEL
]
knob to change the setting
to “ATAS”.
5. Press and hold the
[
F
]
button for one second to
return to normal operation.
Operation
AUTOMATIC TUNING
1. Press the
[
TUNE
]
button briefly to activate the
Automatic Antenna Tuner.
The “ ” icon will appear in the display.
If the transceiver frequency is out of the amateur
band, the “ ” icon will not appear.
If the antenna SWR is High (more than 1:2.0), the
” icon will blink.
2. Press and hold the
[
TUNE
]
button for one second
to begin automatic tuning. The transmitter will be
engaged, and the “ ” icon will blink while tun-
ing is in progress.
3. Tuning will stop automatically when a low SWR is
achieved. You may Press and hold the
[
TUNE
]
button for one second while tuning is in progress,
to cancel the automatic tuning.
[
DSP/SEL
]
Knob
[
F
]
button
[
TUNE
]
button
Page 93FT-450D OPERATION MANUAL
I
NSTALLATION
OF
O
PTIONAL
A
CCESSORIES
ACTIVE-TUNING ANTENNA SYSTEM
(
ATAS-100/-120/120A
)
OPERATION
MANUAL TUNING
1. Press the
[
TUNE
]
button briefly to activate the
Automatic Antenna Tuner.
The “ ” icon will appear in the display.
If the transceiver frequency is out of the amateur
band, the “ ” icon will not appear.
If the antenna SWR is High (more than 1:2.0), the
” icon will blink.
2. Press and hold in the microphone PTT switch.
With the transceiver in the “transmit” mode, press
and hold in the
[
BAND
]
button (to raise the an-
tenna) or the
[
BAND
]
button (to lower the an-
tenna). While you hold in one of these keys, the
FT-450D will generate a carrier, and you may
watch the SWR meter of the FT-450D, looking for
the meter indication to reach its minimum value.
When this is reached, release the
[
BAND
]
or
[
BAND
]
button, then release the PTT switch to
return to the “receive” mode.
[
TUNE
]
button
A
T
A
S
-
1
2
0
A
FT-450D
INPUT
DC 13.8V
2 2A
ANT
GND
EXT
SPKR
CATLINEARTUNERDATA
After-market mount
Page 94 FT-450D OPERATION MANUAL
I
NSTALLATION
OF
O
PTIONAL
A
CCESSORIES
CARRYING HANDLE MHG-1 INSTALLATION
The MHG-1 is a Carrying Handle designed to match FT-450D transceiver.
Parts List
Handle ................................................................ 1pc
Handle end ....................................................... 2pcs
Mounting Screws (M4x15B) ............................. 2pcs
Installation
Screw the Carrying Handle to the FT-450D using the
supplied screws.
Do not install the supplied MHG-1 Mounting
Screws if you are not installing the MHG-1!
Also, do not use an improper screw for mount-
ing the MHG-1! An improper screw may cause
a “short circuit” to the internal circuitry, caus-
ing serious damage!
Handle
Handle end
(2 pcs)
Mounting Screws
(2 pcs)
Page 95FT-450D OPERATION MANUAL
I
NSTALLATION
OF
O
PTIONAL
A
CCESSORIES
MOUNTING BRACKET MMB-90 INSTALLATION
The MMB-90 is a mounting bracket designed to match the YAESU FT-450D transceiver.
Parts List
Mounting Bracket ........................................................ 1 pc
Double Face Adhesives ............................................ 2 pcs
Screws, Washers & Nuts for Mounting Bracket
M4 Knob-screws .................................................. 4 pcs
M5X20 Screws ..................................................... 4 pcs
M5X20 Tapping screws ........................................ 4 pcs
Washers ............................................................... 8 pcs
Washers ............................................................... 4 pcs
N5 Nut .................................................................. 4 pcs
Installation Procedure
1. Determine a convenient mounting location with
sufficient clearance and ventilation. Use the
bracket as a template and locate the mounting
holes. Use a 4.8-mm (3/16#) bit to drill the holes.
Secure the bracket with the supplied screws,
washers and nuts.
NOTE:
The supplied double-sided adhesive tape may be
used to temporarily hold the mobile mounting
bracket in place, while drilling the holes for instal-
lation.
Stay (user prepared)
2. Position the transceiver in the bracket so the holes
in the side are aligned with those in the bracket.
Fasten the transceiver into place using the sup-
plied Knob-screws (M4).
Upper side
Lower side
M4 Knob-screws
(4 pcs)
Page 96 FT-450D OPERATION MANUAL
General
Rx Frequency Range: 30 kHz - 56 MHz (operating)
160 - 6 m (specified performance, Amateur bands only)
Tx Frequency Ranges: 160 - 6 m (Amateur bands only)
Frequency Stability: ±1 ppm/hour (@+25 °C, after warmup)
Operating Temperature Range: 14 °F ~ 122 °F (–10 °C ~ +50 °C)
Emission Modes: A1A (CW), A3E (AM), J3E (LSB, USB), F3E (FM)
Frequency Steps: 10 Hz (SSB & CW), 100 Hz (AM & FM)
Antenna Impedance: 50 Ohms, unbalanced
Power Consumption: Rx (signal present) 1.5 A
Tx (100 W) 22 A
Supply Voltage: DC 13.8 V ± 10%
Dimensions (WxHxD): 9’ x 3.3” x 8.5” (229 x 84 x 217 mm)
Weight (approx.): 8.8 lb (4.0 kg)
Transmitter
Power Output: 100 watts (25 watts AM carrier)
Modulation Types: J3E (SSB): Balanced,
A3E (AM): Low-Level (Early Stage),
F3E (FM): Variable Reactance
Maximum FM Deviation: ±5.0 kHz / ±2.5 kHz
Harmonic Radiation: Better than –60 dB (160 - 10m Amateur bands)
Better than –70 dB (6m Amateur band)
SSB Carrier Suppression: At least 60 dB below peak output
Undesired Sideband Suppression: At least 60 dB below peak output
Audio Response (SSB): Not more than –6 dB from 300 to 2400 Hz
Microphone Impedance: 600 Ohms (200 to 10 kOhms)
SPECIFICATIONS
Page 97FT-450D OPERATION MANUAL
SPECIFICATIONS
Receiver
Circuit Type: Double-conversion superheterodyne
Intermediate Frequencies: 67.899 MHz / 24 kHz
Sensitivity (IPO “OFF”, ATT: OFF): SSB (2.4 kHz, 10 dB S+N/N)
0.25 µV (1.8 - 2.0 MHz)
0.25 µV (3.5 - 30 MHz)
0.20 µV (50 - 54 MHz)
AM (6 kHz, 10 dB S+N/N, 30 % modulation @400 Hz)
2.00 µV (1.8 - 2.0 MHz)
2.00 µV (3.5 - 30 MHz)
1.00 µV (50 - 54 MHz)
FM (BW: 15 kHz, 12 dB SINAD)
0.50 µV (28 - 30 MHz)
0.30 µV (50 - 54 MHz)
There is no specification in frequency ranges not listed.
Squelch Sensitivity: SSB/CW/AM
(IPO “OFF”, ATT: “OFF”) 2.50 µV (1.8 - 30 MHz)
1.00 µV (50 - 54 MHz)
FM
0.32 µV (28 - 30 MHz)
0.16 µV (50 - 54 MHz)
There is no specification in frequency ranges not listed.
Selectivity (–6/–60 dB): Mode 6 dB 60 dB
CW 250 Hz or better 700 Hz or less
SSB 2.2 kHz or better 4.5 kHz or less
AM 6 kHz or better 20 kHz or less
FM 15 kHz or better 30 kHz or less
FM-N 9 kHz or better 25 kHz or less
Image Rejection: 80 dB or better
IF Rejection: 80 dB or better (160 - 10m Amateur bands)
65 dB or better (6m Amateur band)
Maximum Audio Output: 2.2 W into 4 Ohms with 10% THD
Audio Output Impedance: 4 to 16 Ohms (8 Ohms: nominal)
Conducted Radiation: 47 dBm < 1000 MHz, – 57 dBm > 1000 MHz
Specifications are subject to change, in the interest of technical improvement, without notice or obligation, and
are guaranteed only within the amateur bands.
Page 98 FT-450D OPERATION MANUAL
FCC N
OTICE
1. Changes or modifications to this device not expressly approved by VERTEX STANDARD could void the user’s
authorization to operate this device.
2. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions; (1) this
device may not cause harmful interference, and (2) this device must accept any interference including interference
that may cause undesired operation.
3. The scanning receiver in this equipment is incapable of tuning, or readily being altered, by the User to operate
within the frequency bands allocated to the Domestic public Cellular Telecommunications Service in Part 22.
DECLARATION BY MANUFACTURER
The scanner receiver is not a digital scanner and is incapable of being converted or modified a digital scanner
receiver by any user.
WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS
PROHIBITED UNDER FCC RULES AND FEDERAL LAW.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
THIS CLASS B DIGITALAPPARATUS COMPLIES WITH CANADIAN ICES-003.
Declaration of Conformity
We, Yaesu UK Ltd. declare under our sole responsibility that the following equipment complies with the
essential requirements of the Directive 1999/5/EC and 2004/104/EC.
Type of Equipment: HF Transceiver
Brand Name: YAESU
Model Number: FT-450 / FT-450D
Manufacturer: Vertex Standard Co., Ltd.
Address of Manufacturer: 4-8-8 Nakameguro Meguro-Ku, Tokyo 153-8644, Japan
Applicable Standards:
This equipment is tested and conforms to the essential requirements of directive, as included in follow-
ing standards.
EN 301 783-2 V1.1.1
Radio Standard:
EN 301 489-1 V1.8.1
EMC Standard: EN 301 489-15 V1.2.1
EN 60065 :2002+A1 :2006+A11 :2008
Safety Standard:
The technical documentation as required by the Conformity Assessment procedures is kept at the
following address:
Company: Yaesu UK Ltd.
Address: Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U.K.
This transceiver works on frequencies which are not generally permit-
ted.
As for the actual usage, the user has to possess an amateur radio licence.
Usage is allowed only in the frequency bands which are allocated for
amateur radios.
Attention in case of use
AUT BEL BGR CYP CZE DEU DNK
ESP EST FIN FRA GBR GRC HUN
IRL ITA LTU LUX LVA MLT NLD
POL PRT ROM SVK SVN SWE CHE
ISL LIE NOR
List of the practicable area
Copyright 2010
VERTEX STANDARD CO., LTD.
All rights reserved
No portion of this manual
may be reproduced without
the permission of
VERTEX STANDARD CO., LTD.
Printed in Japan
1012M-0Y
EH024H250
16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yaesu FT-450D wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info