Bedienungsanleitung Yaesu FT-450D (Seite 70 von 102) (Englisch)

674732

Zoom out

Zoom in

Vorherige Seite

1/102

Nächste Seite

Page 68 FT-450D OPERATION MANUAL

ROGRAMMABLE

EMORY

CANNING

(

PMS

)

To limit scanning (and manual tuning) within a particular frequency range, you can use the Programmable

Memory Scanning (PMS) feature, which utilizes two special-purpose memory pairs (“MEM-P1L/MEM-P1U” and

“MEM-P2L/MEM-P2U”). The PMS feature is especially useful in helping you to observe any operating sub-band

limits, which apply to your Amateur license class.

1. Store the Lower and Upper tuning/scanning limit

frequencies into the memory pair “MEM-P1L” and

“MEM-P1U”, respectively, or “MEM-P2L” and

“MEM-P2U”. See page 58 for details regarding

memory storage.

2. Press the

[

]

button, followed by the

[

SCAN/PMS

]

button.

3. Rotate the

[

DSP/SEL

]

knob to select “PMS-1”

“PMS2” or “PMS1+2”.

PMS-1: The scanner will be limited within the

frequency range programmed in the

memory pair “MEM-P1L/MEM-P1U”.

PMS-2: The scanner will be limited within the

frequency range programmed in the

memory pair “MEM-P2L/MEM-P2U”.

PMS-1+2: The scanner will be limited within the

frequency ranges programmed by both

memory pairs (“MEM-P1L/MEM-P1U”

and “MEM-P2L/MEM-P2U”).

If a memory pair is vacant, the PMS-1+2 selec-

tion is not available.

4. Press the

[

SCAN/PMS

]

button.

5. Rotate the

[

SQL/RF GAIN

]

knob just to the point

where the noise is silenced and the “ ” indi-

cator on the display turns off.

6. Press the

[

SCAN/PMS

]

key to initiate upward

scanning (toward higher frequencies or higher

memory channel numbers).

7. If you want to change direction of the scan while it

is underway, rotate the

[

MAIN DIAL

]

knob one click

in the opposite direction (in this case, one click

counter-clockwise). You will see the scanner re-

verse direction and scan down in frequency.

You may change the direction of the scanner by

pressing and holding the microphone’s

[

]

[

DWN

]

key for one second, if you are using the

MH-31A8J Hand Microphone or optional MD-

100A8X Desktop Microphone.

8. In FM/AM mode, when the scanner encounters a

signal strong enough to open the squelch, the

scanner will halt for five seconds, after which scan-

ning will resume.

In the SSB/CW and SSB-based Data modes,

when the scanner encounters a signal strong

enough to open the squelch, the scanner will step

across the signal very slowly, giving you time to

stop the scan, if you like.

ADVICE:

You may select the manner in which the scanner re-

sumes while it has paused on a signal, using Menu

Item “SCN RES” The default “5Sec” setting will cause

the scanner to resume scanning after five seconds;

you may change it, however, to resume only after the

carrier has dropped out, if you like See page 85.

[

DSP/SEL

]

Knob

[

SCAN/PMS

]

button

[

SQL/RF GAIN

]

Knob

[

MAIN DIAL

]

Knob

[

]

button

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yaesu FT-450D Seite 70

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info