Bedienungsanleitung Yaesu FT-450D (Seite 84 von 102) (Englisch)

674732

Zoom out

Zoom in

Vorherige Seite

1/102

Nächste Seite

Page 82 FT-450D OPERATION MANUAL

CWSPEED

Function: Sets the sending speed for the built-in

Electronic keyer.

Available Values: 4 wpm(20cpm)~60wpm(300cpm)

Default: 12wpm (60cpm)

You can set the sending speed in either: wpm (words

per minute), or cpm (characters per minute).

To button between “Wpm” and “cpm”, just press the

[

]

button.

Note:

If the CW QSK is set to 25ms, the setting of CW

SPEED must not exceed 50wpm (250cpm); And if

the CW QSK is set to 30ms, the setting of CW SPEED

must not exceed 42wpm (210cpm). The delay will

make it impossible to transmit.

CWSTONE (CW SIDE TONE)

Function: Sets the CW sidetone volume level.

Available Values: FIX0 ~ FIX100 or

LNK-50 ~ LNK 0 ~ LNK+50

Default: FIX10 or LNK-8

CWTRAIN (CW TRAINING)

Function: Setting of CW training function

Available Values: N: / A: / M:

Default: N:

Sends random Morse Code five-character groups via

the sidetone.

N: Numeric characters only

A: Alphabet characters only

M: Numeric and Alphabet characters (Mixed)

CWWEIGT (CW WEIGHT)

Function: Sets the CW weight level.

Available Values: 1/2.5~1/4.5

Default: 1/3.0

Sets the Dot/Dash ratio for the built-in electronic keyer.

D DISP (DATA DISP)

Function: DIG (USER-L or USER-U) mode opera-

tion.

Available Values: -3000Hz ~ 0 ~ +3000Hz

Default: 0

Defines the displayed frequency offset during DATA

(USER-L or USER-U) mode operation.

D TYPE (DTAT MODE)

Function: Selects the mode and sideband (if appli-

cable) in the DATA mode.

Available Values: RTTY/USR-L/USR-U

Default: RTTY

RTTY: FSK RTTY operation

USR-L: User-programmed custom operation based

on LSB mode

USR-U: User-programmed custom operation based

on USB mode

DIALSTP (DIAL STEP)

Function: Sets the DIAL knob's tuning speed.

Available Values: SSB/CW: 1 / 10 / 20 (Hz)

AM/FM: 100 / 200 (Hz)

Default: SSB/CW: 10 (Hz), AM/FM: 100 (Hz)

The width of the step of the

[

MAIN DIAL

]

knob can

be set for each mode.

DIG VOX

Function: Sets the gain of the VOX circuitry input

level for the DIG mode.

Available Values: OFF / 1~100

Default: OFF

EMERGEN (EMERGENCY)

Function: Enables Tx/Rx operation on the Alaska

Emergency Channel, 5167.5 kHz.

Available Values: ON/OFF

Default: OFF

When this Menu Item is set to “ON,” the spot fre-

quency of 5167.5 kHz will be enabled. To get to this

frequency, use the

[

DSP/SEL

]

knob to navigate. The

Alaska Emergency Channel will be found between

the Memory channel “US5-001” and “MEM-500.”

NOTE:

Use of this frequency is restricted to amateurs oper-

ating in (or within 92.6 km of) the U.S. State of Alaska,

and it is to be used for emergency communications

only (involving the immediate protection of life or prop-

erty).

KEYHOLD (KEY HOLD TIME)

Function: Sets the hold time for a push button to

activate.

Available Values: 0.5 / 1.0 / 1.5 / 2.0

Default: 1.0

MENU MODE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yaesu FT-450D Seite 84

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info