Bedienungsanleitung Yaesu FT-60R-E (Seite 49 von 84) (Englisch)

478475

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

FT-60R/E OPERA TING MANUAL 47

frequency which is stored in Memory Channel “000” for more than five seconds, the

radio will automatically transmit a brief (0.5 second) beep tone every 2.5 seconds until the

EAI timer expiration at the power level stored in that memory channel; it is NOT neces-

sary for the incapacitated person to press the PTT switch.

In the Continuous mode, when the FT-60R/E receives the CTCSS tone pair which is

stored in the Receiving Pager Code Memory (configured via Set Mode Item 31: PAG.CDR)

on the frequency which is stored in Memory Channel “000” for more than five seconds,

the radio will automatically transmit (with maximum microphone gain) continuously,

until the EAI timer expiration, at the power level stored in that memory channel; it is NOT

necessary for the incapacitated person to press the PTT switch.

Furthermore, if your call sign is stored in the radio via Set Mode Item 11: CW WRT and you have

enabled the CW identifier by Set Mode Item 10: CWID, the radio will transmit your callsign on the

air when the EAI feature is first engaged by the remote page, and every 10 minutes thereater.

The “callsign” ID can be changed to any desired sequence of characters, such as a name.

After sending the callsign or name, the radio will repeatedly transmit three tones for a

user-defined period of time (between 1 and 30 minutes). The callsign or name will be

transmitted every 10 minutes.

The Emergency Automatic ID (EAI) Feature requires that you (1) store the CTCSS Tone

Pair into the Receiving Pager Memory (see page 44 for procedure), and (2) store the desired

UHF coordination frequency into Memory Channel “000” (see page 28 for procedure).

To enable this feature:

1. Press the

[

F/W

]

key, then press the

[

( )

SET

]

key to enter the Set mode.

2. Rotate the DIAL knob to select Set Mode Item 18: EAI.

3. Press the

[

F/W

]

key momentarily to enable adjustment of this

Set Mode Item.

4. Rotate the DIAL knob to select the desired EAI mode (Interval

EAI or Continuous EAI) and its transmit time (1-10, 15, 20, 30,

40, and 50 minutes) or OFF.

5. Press the PTT switch to save the new setting and exit to normal operation.

6. To disable the Emergency Automatic ID feature, just repeat the above procedure,

rotating the DIAL knob to select “OFF” in step 4 above.

When the Emergency Automatic ID feature is activated, the “ ”

icon will blink in the LCD.

The FT-60R/E will ignore the EAI feature when the (1) the squelch is open,

(2) there is an incoming the signal on the operating frequency, (3) the oper-

ating frequency is the same as the frequency which is stored in the Memory

Channel “000,” or (4) a VHF frequency is stored in Memory Channel “000.”

EMERGENCY FEATURE

EMERGENCY AUTOMATIC ID

(

EAI

)

FEATURE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yaesu FT-60R-E Seite 49

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info