Bedienungsanleitung Yaesu FT-8800R (Seite 48 von 72) (Englisch)

478467

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

46 FT-8800R Operating Manual

The ARTS feature uses DCS signaling to inform both parties when you and another ARTS-

equipped station are within communications range. This may be particularly useful during

Search-and Rescue situations, where is important to stay in contact with other members of

your group.

Both stations must set up their DCS codes to the same code number, then activate their

ARTS feature using the command appropriate for their radio. Alert ringers may be acti-

vated, if desired.

Whenever you push the PTT switch, or every 25 seconds after ARTS is activated, your

radio will transmit a signal which includes a (subaudible) DCS signal for about one second.

If the other radio is in range, the beeper will sound (if enabled) and the display will show

“

IN.RNGIN.RNG

IN.RNG” as opposed to the out of range display “

OUT.RNGOUT.RNG

OUT.RNG” in which ARTS operation

begins.

Whether you talk or not, the polling every 25 seconds will continue until you de-activate

ARTS. Every 10 minutes, moreover, you can have your radio transmit your callsign via

CW, so as to comply with identification requirements. When ARTS is de-activated, DCS

will also be deactivated (if you were not using it previously in non-ARTS operation).

If you move out of range for more than one minute (four pollings), your radio will sense

that no signal has been received, three beeps will sound, and the display will revert to

“

OUT.RNGOUT.RNG

OUT.RNG.” If you move back into range, your radio will again beep, and the display will

change back to the “

IN.RNGIN.RNG

IN.RNG” indication.

During ARTS operation, it is not possible to change the operating frequency or other set-

tings on the “Main” band; you must terminate ARTS in order to resume normal operation.

This is a safety feature designed to prevent accidental loss of contact due to channel change,

etc. Here is how to activate ARTS:

Basic ARTS Setup and Operation

1. Set your radio and the other radio(s) to the same DCS code number, per the discussion

on page 30.

2. Press the

[

SET

]

key momentarily to enter the Set mode.

3. Rotate the “Main” band DIAL knob to select Menu #3 (

ARTSARTS

ARTS).

4. Press the “Main” band DIAL knob momentarily, then rotate the “Main” band DIAL

knob to select the desired ARTS beep option. The available options are:

IN RNGIN RNG

IN RNG: The beeps are issued only when the radio first confirms that you are within

range, but does not re-confirm with beeps thereafter.

ALWAYSALWAYS

ALWAYS: Every time a polling transmission is received from the other station, the

alert beeps will be heard.

5. Press the “Main” band DIAL knob momentarily. You will observe the “

OUT.RNGOUT.RNG

OUT.RNG” dis-

play on the LCD. ARTS operation has now commenced.

ARTS

: AUTO RANGE TRANSPONDER SYSTEM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yaesu FT-8800R Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info