Bedienungsanleitung Yaesu FT-897D (Seite 14 von 76) (Englisch)

478500

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Page 12 FT-897D OPERATING MANUAL

Liquid Crystal Display

The Liquid Crystal Display (LCD) provides indication

of the operating frequency and other aspects of trans-

ceiver status.

FUNC Keys

These three keys select many of the most important op-

erating features of the transceiver. When you press the

[

]

key, then rotate the MEM/VFO CH knob, the cur-

rent function of that key will appear above each of the

[

]

[

]

, and

[

]

keys (along the bottom of the LCD).

You may scroll the display through 17 rows of functions

available for use via the

[

]

[

]

, and

[

]

keys.

The available features are shown in page 14.

MIC Jack

Connect the supplied MH-31A8J Hand Microphone to

this jack.

[

]

Key

Press this key momentarily to enable the changing of the

function of the Multi Function keys (

[

]

[

]

, and

[

]

)

by the MEM/VFO CH knob.

Press and hold this key for one second to activate the

“Menu” mode.

LOCK Key

Pressing this key locks the front panel keys so as to pre-

vent accidental frequency change. The LOCK key it-

self, though, will never be disabled.

MAIN DIAL

This is the main tuning dial for the transceiver. It is used

both for frequency tuning as well as “Menu” setting in

the transceiver.

AF Knob

The (inner) VOL knob adjusts the receiver audio vol-

ume level presented to the internal or external speaker.

Clockwise rotation increases the volume level.

SQL/RF Knob

In the USA version, this (outer) SQL/RF knob adjusts

the gain of the receiver’s RF and IF stages. Using Menu

Mode No-080

[

SQL/RF GAIN

]

, this control may be

changed to function as a Squelch control, which may be

used to silence background noise when no signal is

present. In the other versions, its default setting is set to

“Squelch.”

CLAR/IF SHIFT Key

Pressing this key activates the Receiver Clarifier fea-

ture. When this feature is activated, the CLAR knob is

used to set a tuning offset of up to ±9.99 kHz. The

transmitter’s frequency is not affected by the setting of

the Clarifier.

Press and hold this key for one second to activate the IF

Shift feature, which allows you to use the MEM/VFO

CH knob to adjust the center frequency of the IF filter’s

passband response.

FRONT PANEL CONTROL & SWITCHES

BATT-B

BATT-A

FAST

GND

PTT

MICMIC GN

+5 V

DOWN

PHONES Jack

This 1/4-inch, 3-contact jack accepts either monaural or

stereo headphones with 2- or 3-contact plugs. When a

plug is inserted, the loudspeaker is disabled. The audio

level varies according to the setting of the front panel’s

AF knob.

POWER Switch

Press and hold in the POWER switch for one second to

turn to the transceiver on or off.

While the transceiver is turned on, pressing this switch

momentarily will engage the “Fast Tuning” mode, to al-

low more rapid frequency navigation (a small “running

man” icon will be observed in the bottom right-hand

corner of the LCD).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yaesu FT-897D Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info