478504
114
Zoom out
Zoom in
Vorherige Seite
1/132
Nächste Seite
Page 112 FT-950 OPERATING MANUAL
041 A1A CW AUTO
Function: Enables/disables CW keying while operating
on SSB.
Available Values: OFF/50/On
Default Setting: OFF
OFF:Disables CW keying while operating on SSB.
50: Enables CW keying only while operating SSB on 50
MHz (but not HF).
On: Enables CW keying while operating on SSB (all TX
bands).
NOTE:
This feature allows you to move someone from SSB to
CW without having to change modes on the front panel.
042 A1A BFO
Function: Sets the CW carrier oscillator injection side for
the CW mode.
Available Values: USb/LSb/Auto
Default Setting: USb
USb: Injects the CW carrier oscillator on the USB side.
LSb: Injects the CW carrier oscillator on the LSB side.
Auto: Injects the CW carrier oscillator on the LSB side
while operating on the 7 MHz band and below, and
the USB side while operating on the 10 MHz band
and up.
043 A1A BK-IN
Function: Sets the CW “break-in” mode.
Available Values: SEni/FuLL
Default Setting: SEni
SEni (SEMI):The transceiver will operate in the semi
break-in mode. The delay (receiver recovery) time is set
via the Menu item “044 A1A DELAY”.
FuLL: The transceiver will operate in the full break-in
(QSK) mode.
044 A1A DELAY
Function: Adjusts the Keying Delay (receiver recovery)
time on the CW mode.
Available Values: 30 ~ 3000 msec (10 msec/step)
Default Setting: 200 msec
045 A1A PITCH
Function: Adjusts your preferred CW tone pitch.
Available Values: 300 ~ 1050 Hz (50 Hz/step)
Default Setting: 700 Hz
046 A1A WEIGHT
Function: Sets the Dot:Dash ratio for the built-in elec-
tronic keyer.
Available Values: (1:) 2.5 ~ 4.5
Default Setting: 3.0
047 A1A FRQDISP
Function: Selects the frequency Display Format for the
CW mode.
Available Values: dir/OFSt
Default Setting: OFSt
dir (Direct Frequency):Displays the receiver carrier fre-
quency, without any offset added.
When changing modes between
SSB and CW, the frequency dis-
play remains constant.
OFSt (Pitch Offset): This frequency display reflects the
added BFO offset.
048 A1A PC KYNG
Function: Enables/disables CW keying from the “DATA
PTT” terminal (pin 3) on the rear panel’s RTTY/PKT jack
while operating on the CW mode.
Available Values: EnA (Enable)/diS (Disable)
Default Setting: diS (Disable)
049 A1A QSKTIME
Function: Selects the time delay between when the PTT
is keyed and the carrier is transmitted during QSK opera-
tion when using the internal keyer.
Available Values: 15/20/25/30 msec
Default Setting: 15 msec
MENU MODE
MODE-CW GROUP
114

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

yaesu-ft-950

Suche zurücksetzen

  • Hat der FT950 eine Verzögerungsschaltung zum Steuern der VL 1000 Eingereicht am 24-1-2018 09:08

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yaesu FT-950 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info