Bedienungsanleitung Yaesu FT-DX9000 (Seite 6 von 156) (Englisch)

674754

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

Page 4 FT DX 9000D OPERATION MANUAL

Before You Begin. . .

1. Connecting AC Power

There are two power switches on this transceiver, one each on the rear and front panels. If the rear panel’s Power switch is

not turned on, the front panel Power switch will not function.

Ì Push the rear panel’s Power

switch to the I position

to apply power from the

power supply to the OCXO

(Reference Crystal Oven)

and to enable the front panel

power switch.

Ì Press and hold in the front

panel Power switch for two

seconds to turn the trans-

ceiver on.

Note

The opening screen will appear on the TFT display, and

the self-check function of the CPU inside the radio will

begin. Then, the µ-Tuning circuitry will receive the data

from the CPU, and it will perform its own self-check, and

will preset itself to the proper settings for the current op-

erating frequency.

While the µ-Tuning circuitry is obtaining the data, the drive

mechanism will move from one end of its range to the

other end (fast), and this will cause a temporary “motor”

noise that can be heard; this, does not represent any trouble

or problem.

When the radio is turned on for the first time, it takes about

50 seconds (from turning the radio on to completing the

self-check) until the radio becomes ready to use; how-

ever, from the next time you turn it on, it will take around

10 seconds until the transceiver is ready for full opera-

tion.

2. Setting Your Local Time

When first turning on the FT DX 9000, be sure to set the local time to match your location's time zone. If you do not do this,

several functions will not work correctly, including the World Clock, Great Circle Map, etc.; please see the appropriate

section of the TFT Operating Manual for details on Local Time Setup.

3. Configuring Your FT DX 9000 Using the Menu

The FT DX 9000 is configured, at the factory, with its various functions set up in a manner typical for most operation. Via

the “Menu” system, you may change these settings to match the way you want your transceiver to operate.

Menu programming is enabled by pressing the MNU

(Menu) key momentarily. You may then rotate the Main

Tuning Dial to display the desired Menu item, in the menu

list, on the TFT. Each of the settings can be changed or

customized via the CLAR/VFO-B knob, as you like, in

this mode.

Once you have made a change to the configuration of a

Menu item or items, you must press and hold in the

MNU (Menu) key for two seconds to save the new set-

tings and exit to normal operation.

If you wish to cancel a change to a Menu item or items,

just press the MNU key momentarily. If you do not press

and hold in the MNU key in for two seconds, any changes

you have made will not be saved.



Main Tuning Dial

MNU key

CLAR/VFO-B Knob

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yaesu FT-DX9000 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info