Bedienungsanleitung Yaesu FT-DX9000 (Seite 30 von 156) (Englisch)

674754

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

Page 28 FT DX 9000D OPERATION MANUAL





B Switch

Pressing this button momentarily exchanges the con-

tents of the main band (VFO-A) (or a recalled memory

channel) and the sub band (VFO-B).

V/M Switch

This button toggles main band (VFO-A) receiver op-

eration between the memory system and the VFO.

Either “VFO,” “MEM,” or “M TUNE” will be dis-

played to the left of the main frequency display field

to indicate the current selection. If you have tuned off

of a Memory channel frequency (M TUNE), pressing

this button returns the display to the original memory

contents (MEM), and pressing it once more returns

operation to the Main VFO.

MA Switch

Pressing this button momentarily displays the contents

of the currently-selected memory channel for three sec-

onds.

Holding this button in for 2 seconds copies the data

from the currently-selected memory to the Main VFO

(VFO-A), as two beeps sound. Previous data in the

Main VFO will be overwritten.

A M Switch

Pressing and holding in this key for 1/2 second (until

the double beep) copies the current operating data from

the main band (VFO-A) into the currently selected

memory channel, overwriting any previous data stored

there.

Also, pressing and holding in this button after recall-

ing a memory, without first retuning, causes the

memory channel to be “masked,” and repeating the

process restores the masked memory.

A-BUSY Indicator

This LED glows green whenever the Main band (VFO-

A) receiver squelch is open. If this indicator is not

illuminated, and reception seems to have been “lost”

on the Main receiver for no apparent reason, check

the position of the SQL control (# , described

previously) and rotate it fully counter-clockwise to re-

store reception.

TX Indicator

This indicator glows Red during transmission.

If you attempt to transmit while operating outside of

an Amateur band, this indicator will blink Red, indi-

cating an “out of band” condition.

B-BUSY Indicator

This LED glows green whenever the Sub band (VFO-

B) receiver squelch is open. If this indicator is not

illuminated, and reception seems to have been “lost”

on the Sub receiver for no apparent reason, check the

position of the SUB (VFO-B) SQL control (# ,

described later) and rotate it fully counter-clockwise

to restore reception.

Tuning Offset Indicator

This is a tuning scale that, as configured from the fac-

tory, provides a visual CW tuning indication of the

incoming signal’s offset from your transceiver's CW

carrier frequency, as programmed by the position of

the PITCH control (# , described previously).

SPLIT Indicator

This indicator glows Red when the “Split” mode is

engaged (with the Main and Sub bands operating on

different frequencies).

FRONT PANEL CONTROLS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yaesu FT-DX9000 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info