Bedienungsanleitung Yaesu FT-DX9000 (Seite 45 von 156) (Englisch)

674754

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

Page 43FT DX 9000D OPERATION MANUAL

ASIC

PERATION

: R

ECEIVING

MATEUR

ANDS

1. Plug the AC cable back in, set the rear-panel

Power switch to “

.”

2. Press and hold in the front-panel Power

switch for two seconds to turn the trans-

ceiver on.

3. After about 50 seconds, all circuits will

be initialized. The transceiver will start

up on 7.000.00 MHz LSB, and normal operation may

resume.

Note

To turn power off, press and hold in the front panel

POWER switch for two seconds.

Quick Note

The opening screen on the TFT will be gray, and some

text notes advising status during the boot-up sequence

may appear. When the radio is turned on for the first

time, it takes about 50 seconds (from turning the ra-

dio on to completing the self-check) until the radio

becomes ready to use; however, from the next time

you turn it on, it will take around 10 seconds until the

transceiver is ready for full operation.

4. Rotate the AF GAIN

knob (# ) to set a comfort-

able audio level on incom-

ing signals or noise. Clock-

wise rotation of the AF

GAIN knob increases the

volume level.

Note

When using headphones, start by rotating the AF

GAIN control counter-clockwise, then bring the vol-

ume level up after you put the headphones on. This

will minimize the chance of damage to your hearing

caused by an unexpectedly-high audio level.

5. Press the MAIN RX switch (# ) to engage the

Main (VFO-A) receiver, the imbedded LED will glow

Green.

BAND key

POWER swtch

AF GAIN knob

Main (VFO-A)

RX switch

Main (VFO-A)

Advice

If you press the MAIN RX key (# ) when the

imbedded LED is already glowing Green, the LED

will now blink on and off; this indicates that the Main

(VFO-A) receiver is temporarily muted. Just press the

MAIN RX key once more to restore Main (VFO-

A) receiver operation.

Press the SUB RX switch (# ) to engage Dual

Reception (using Sub the (VFO-B) receiver in addi-

tion to the Main (VFO-A) receiver). When you press

the SUB RX key, its imbedded LED will glow green;

pressing this key once more will turn off the Sub (VFO-

B) receiver, and the impeded LED will glow dark. Use

the Sub Receiver’s AF GAIN knob (# ) to adjust

the Sub (VFO-B) receiver volume level.

6. Press the A switch (# ) to enable

the capability to change the operation

for the Main (VFO-A) band the im-

bedded LED will glow Red.

7. Surrounding the TFT are the band

selection keys; press the BAND

key corresponding to the Amateur

band on which you wish to begin op-

eration.

Advice

H One-touch selection of each

Amateur band between 1.8 and

50 MHz is provided.

H If you press the BAND/MHz

key (# ) momentarily, the CLAR/VFO-B

knob (# ) may be used as a band selection knob.

If the CLAR/VFO-B

knob is pressed and held

in for two seconds, rota-

tion of the BAND/

MHz key allows fre-

quency navigation in 1

MHz steps.

H When the BAND/MHz key’s imbedded LED

is illuminated, the CLAR/VFO-B knob controls

the functions associated with the BAND/MHz

key.

CLAR/VFO-B knob

AF GAIN knob

Sub (VFO-B)

RX swtch

Sub (VFO-B)

BAND/MHz switch

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yaesu FT-DX9000 Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info