478507
2
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
INSTALLATION
The power supply in the VP-1000 is capable of operation from 100 ~ 240 VAC at 50 or 60 Hz. If you
have a choice between these two voltage ranges, use the higher voltage to minimize losses in the AC
cable.
Connect the supplied DC Power Cable between the VP-1000 OUTPUT jack and the VL-1000 DC
48V IN jack, and connect the supplied Control
Cable between the VP-1000 CONTROL socket
and the VL-1000 CONTROL socket.
Turn the Circut Breaker on the VP-1000 rear
panel ON, then turn the VP-1000 MAIN switch
ON to activate the power supply. Always turn the
VP-1000 Circut Breaker and MAIN switch on
before turning on the VL-1000 P
OWER switch.
To assure long life of the components, a primary
consideration in setting up the VP-1000 is pro-
viding for adequate ventilation around the cabi-
net. The cooling system of the VP-1000 must be
free to draw cool air in at the bottom of the chas-
sis, and to expel warm air out of the rear panel.
Provide a few centimeters of space around each
side of the VP-1000. Avoid heating vents and
window locations that could expose the VP-1000
to excessive direct sunlight, especially in hot climates.
AC POWER CONNECTIONS
The VP-1000 Power Supply does not require any transformer re-wiring, nor any changing of a switch
position; the power supply will operate from either 230 or 120 Volt line voltages without configuration
changes.
However, the AC power cable/plug configuration will be somewhat different, depending on the coun-
try in which you purchased your power supply. In some countries, the VP-1000 is shipped with the
standard 230 Volt connector appropriate for your location. In those areas where there are multiple
230 Volt connectors in common use, the VP-1000 is shipped without the power connector; one may
be obtained at a local hardware or electrical supply store.
Pictorial diagrams of the common 230 and 120 Volt AC connectors in use are shown below. When
wiring your own connector, be absolutely certain to observe the proper polarity on the pin connec-
tions. Consult with an electrician if you have any doubts about your wiring!
Be sure that your house wiring is capable of sufficient current capacity on the 230 Volt circuit to be
used, especially if this circuit is shared with household appliances. It always is preferable to operate
the VP-1000 from a dedicated 230 Volt circuit with its own circuit breaker.
CIRCUIT DIAGRAM
Australian
PLUG
European
PLUG
USA PLUG UK PLUG
(U.S.A. version)
(viewed from plug prong side)
(European version)
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yaesu VP-1000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info