Bedienungsanleitung Yamaha 01V96 version 2 (Seite 5 von 328) (Englisch)

559197

Zoom out

Zoom in

Vorherige Seite

1/328

Nächste Seite

(5)-1

2/2

• Do not insert your ﬁngers or hand in any gaps or openings on the device (vents,

etc.).

•Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any

gaps or openings on the device (vents, etc.) If this happens, turn off the power

immediately and unplug the power cord from the AC outlet. Then have the

device inspected by qualiﬁed Yamaha service personnel.

• Do not use headphones for a long period of time at a high or uncomfortable

volume level, since this can cause permanent hearing loss. If you experience

any hearing loss or ringing in the ears, consult a physician.

• Do not apply oil, grease, or contact cleaner to the faders. Doing so may cause

problems with electrical contact or fader motion.

• Do not rest your weight on the device or place heavy objects on it, and avoid use

excessive force on the buttons, switches or connectors.

• This device has a rear-panel slot for installing mini-YGDAI cards. For technical

reasons, certain card combinations are not supported. Before installing any

cards, check the Yamaha web site (see page 6) to see whether your card is

compatible.

Installing cards that are not endorsed by Yamaha may cause electrical shock,

ﬁre, or damage to the unit.

• This device has a built-in backup battery. When you unplug the power cord from

the AC outlet, the internal data is retained. However, if the backup battery fully

discharges, this data will be lost. If the backup battery is running low, when you

turn on the device the display indicates “WARNING Low Battery!.” In this case,

immediately save the data to an external media using MIDI Bulk Dump, then

have qualiﬁed Yamaha service personnel replace the backup battery.

• Using a mobile telephone near this unit may induce noise. If noise occurs, use the telephone away from the unit.

• The digital circuits of this unit may induce a slight noise into nearby radios and TVs. If noise occurs, relocate the affected equipment.

• When you change the wordclock settings on any device in your digital audio system, some devices may output noise, so turn down your power amps beforehand,

otherwise your speakers may be damaged.

XLR-type connectors are wired as follows (IEC60268 standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-).

Insert TRS phone jacks are wired as follows: sleeve: ground, tip: send, and ring: return.

Yamaha cannot be held responsible for damage caused by improper use or modiﬁcations to the device, or data that is lost or destroyed.

Always turn the power off when the device is not in use.

The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult qualiﬁed Yamaha service

personnel about replacing defective components.

* The illustrations and screen displays as shown in this Owner’s Manual are for instructional purposes only, and may be different from the ones on your device.

* The company names and product names in this Owner’s Manual are the trademarks or registered trademarks of their respective companies.

Handling caution Backup battery

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha 01V96 version 2 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha 01V96 version 2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info