Bedienungsanleitung Yamaha 01V96 (Seite 309 von 334) (Englisch)

517046

309

Zoom out

Zoom in

Vorherige Seite

1/334

Nächste Seite

MIDI Data Format 309

01V96—Owner’s Manual

MIDI Data Format

1. DATA FORMAT

1.1 CHANNEL MESSAGE

1.2 SYSTEM COMMON MESSAGE

1.3 SYSTEM REALTIME MESSAGE

1.4 EXCLUSIVE MESSAGE

1.4.1 Real Time System Exclusive

1.4.2 System Exclusive Message

1.4.2.1 Bulk Dump

The following data types of bulk dump are used on the 01V96.

1.4.2.2 PARAMTER CHANGE

The following data types of parameter change are used by the 01V96.

* ‘tx’ indicates that the data can be transmitted from the 01V96, and

‘rx’ indicates that the data can be received by the 01V96.

2. Format Details

2.1 NOTE OFF (8n)

Reception

If [OTHER ECHO] is ON, these message are echoed from MIDI OUT.

If the [Rx CH] matches, these messages are received and used to control effects.

2.2 NOTE ON (9n)

Reception

If [OTHER ECHO] is ON, these messages are echoed from MIDI OUT.

If the [Rx CH] matches, these messages are received and used to control effects.

2.3 CONTROL CHANGE (Bn)

Reception

If [Control Change ECHO] is ON, these messages are echoed from MIDI OUT.

If [TABLE] is selected, these message are received if [Control Change Rx] is ON,

and will control parameters according to the [Control assign table] settings.

The parameters that can be set are defined in the Control Change Assign Pa-

rameter List.

If [NRPN] is selected, these messages are received if [Control Change Rx] is ON

and the [Rx CH] matches, and will control the parameter that is specified by the

four messages NRPN control number (62h, 63h) and Data Entry control num-

ber (06h, 26h). Parameter settings are defined in the Control Change Assign Pa-

rameter List.

Transmission

If [TABLE] is selected, operating a parameter specified in the [Control assign ta-

ble] will cause these messages to be transmitted if [Control Change Tx] is ON.

The parameters that can be specified are defined in the Control Change Assign

Parameter List.

If [NRPN] is selected, operating a specified parameter will cause data to be

transmitted on the [Tx CH] if [Control Change Tx] is ON, using the four mes-

sages NRPN control number (62h, 63h) and Data Entry control number (06h,

26h). Parameter settings are defined in the Control Change Assign Parameter

List.

This data cannot be transmitted via control change to Studio Manager since

there is no guarantee that the contents of the tables will match. (Parameter

Change messages will always be used.)

Command rx/tx function

8n NOTE OFF rx Control the internal effects

9n NOTE ON rx Control the internal effects

Bn CONTROL CHANGE rx/tx Control parameters

Cn PROGRAM CHANGE rx/tx Switch scene memories

Command rx/tx function

F1 MIDI TIME CODE QUARTER

FRAME

rx MTC

Command rx/tx function

F8 TIMING CLOCK rx MIDI clock

FE ACTIVE SENSING rx Check MIDI cable connections

FF RESET rx Clear running status

Command rx/tx function

F0 7F dd 06 … F7 MMC

COMMAND

tx MMC command

F0 7F dd 07 … F7 MMC RESPONSE rx MMC response

F0 7F dd 01 … F7 MIDI TIME CODE rx MTC full message

Command rx/tx function

F0 43 0n 7E … F7 BULK DUMP

DATA

rx/tx

BULK DUMP DATA

F0 43 2n 7E … F7 BULK DUMP

REQUEST

rx/tx

BULK DUMP REQUEST

Data name tx/rx function

‘m’ tx/rx Scene Memory & Request

(compressed data)

‘S’ tx/rx Setup Memory & Request

‘R’ tx/rx Input patch library & Request

‘O’ tx/rx Output patch library & Request

‘H’ tx/rx Channel library & Request

‘G’ tx/rx Gate library & Request

‘Y’ tx/rx Compressor library & Request

‘Q’ tx/rx Equalizer library & Request

‘E’ tx/rx Effect library & Request

‘P’ tx/rx Program change table & Request

‘C’ tx/rx Control change table & Request

‘L’ tx/rx User deﬁne layer & Request

‘V’ tx/rx User deﬁne key & Request

‘U’ tx/rx User assignable layer & Request

‘N’ tx/rx Plug-in Effect Card Data & Request

Command rx/tx function

F0 43 1n 3E 0D … F7 RARAMETER

CHANGE

rx/tx 01V96-speciﬁc parameter change

F0 43 3n 3E 0D … F7 PARAMETER

REQUEST

rx/tx 01V96-speciﬁc parameter change

F0 43 1n 3E 7F … F7 PARAMETER

CHANGE

rx/tx General purpose digital mixer

parameter change

F0 43 3n 3E 7F … F7 PARAMETER

REQUEST

rx/tx General purpose digital mixer

parameter request

Type (HEX) tx/rx function

1 (01) tx/rx Edit buffer

2 (02) tx/rx Patch data

3 (03) tx/rx Setup data

4 (04) tx/rx Backup data

15 (0F) tx/rx Cascade data

16 (10) tx/rx Function (recall, store, title, clear)

17 (11) rx Function (pair, copy)

18 (12) rx Function (effect)

19 (13) tx/rx Sort table

20 (14) tx/rx Function (attribute, link)

32 (20) rx Key remote

33 (21) tx/rx Remote meter

34 (22) tx/rx Remote time counter

80 (50) tx/rx Function response (recall, store,

title, clear)

84 (54) tx/rx Function response (attribute, link)

126 (7E) tx/rx Version

127 (7F) tx Active sense

STATUS 1000nnnn 8n

Note off message

DATA 0nnnnnnn nn

Note number

0vvvvvvv vv

Velocity(ignored)

STATUS 1001nnnn 9n

Note on message

DATA 0nnnnnnn nn

Note number

0vvvvvvv vv

Velocity(1-127:on, 0:off)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha 01V96 Seite 309

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha 01V96

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info