Bedienungsanleitung Yamaha 01V96i (Seite 61 von 71) (Englisch)

517047

Zoom out

Zoom in

Vorherige Seite

1/71

Nächste Seite

Analog Input Spec 61

01V96i—Owner’s Manual

Specifications

Analog Input Spec

In these specifications, when dB represents a specific voltage, 0 dB is referenced to 0.775 Vrms.

For 2TR IN levels, 0 dBV is referenced to 1.00 Vrms.

All input AD converters (CH INPUT 1–16) are 24-bit linear, 128-times oversampling. (@fs=44.1, 48 kHz)

+48 V DC (phantom power) is supplied to CH INPUT (1–12) XLR type connectors.

Three PHANTOM +48V switches CH1–4, 5–8, 9–12 turn on the phantom power for inputs 1–4, 5–8, 9–12 respectively.

Analog Output Specs

In these specifications, when dB represents a specific voltage, 0 dB is referenced to 0.775 Vrms.

2TR OUT [L, R] levels, 0 dBV is referenced to 1.00 Vrms.

All output DA converters are 24-bit, 128-times oversampling. (@fs=44.1, 48 kHz)

Input PAD GAIN

Actual Load

Impedance

For Use With

Nominal

Input level

Connector

Sensitivity

1. Sensitivity is the lowest level that will produce an output of +4 dB (1.23 V) or the nominal output level when the unit

is set to maximum gain. (All faders and level controls are maximum position.)

Nominal

Max.

before clip

INPUT A/B

1–12

–60 dB

3 kΩ

50–600 Ω

Mics & 600 Ω

Lines

–70 dB

(0.245 mV)

–60 dB

(0.775 mV)

–40 dB

(7.75 mV)

A: XLR-3-31 type

(Balanced)

B: Phone jack

(TRS) (Balanced)

2. XLR-3-31 type connectors are balanced (1=GND, 2=HOT, 3=COLD).

3. Phone jacks are balanced (Tip=HOT, Ring=COLD, Sleeve=GND).

–16 dB

–26 dB

(38.8 mV)

–16 dB

(123 mV)

+4 dB

(1.23 V)

–6 dB

(388 mV)

+4 dB

(1.23 V)

+24 dB

(12.28 V)

INPUT 13–16

—

–26 dB

10 kΩ 600 Ω Lines

–36 dB

(12.3 mV)

–26 dB

(38.8 mV)

–6 dB

(388 mV)

Phone jack (TRS)

(Balanced)

+4 dB

–6 dB

(388 mV)

+4 dB

(1.23 V)

+24 dB

(12.28 V)

CH INSERT IN

1–12

—10 kΩ 600 Ω Lines

–12 dB

(195 mV)

–2 dB

(616 mV)

+18 dB

(6.16 V)

Phone jack (TRS)

(Unbalanced)

4. CH INSERT IN/OUT phone jacks are unbalanced. (Tip=OUTPUT, Ring=INPUT, Sleeve=GND).

2TR IN [L, R]

—10 kΩ 600 Ω Lines

–10 dBV

(316 mV)

–10 dBV

(316 mV)

+10 dBV

(3.16 V)

RCA pin jack

(Unbalanced)

Output

Actual Source

Impedance

For Use With

Nominal

Output level

Connector

Nominal

Max.

before clip

STEREO OUT [L, R]

75 Ω 600 Ω Lines

+4 dB

(1.23 V)

+24 dB

(12.28 V)

XLR-3-32 type (Balanced)

1. XLR-3-32 type connectors are balanced (1=GND, 2=HOT, 3=COLD).

OMNI OUT 1–4

150 Ω 10 kΩ Lines

+4 dB

(1.23 V)

+24 dB

(12.28 V)

Phone jack (TRS) (Balanced)

2. Phone jacks are balanced (Tip=HOT, Ring=COLD, Sleeve=GND).

MONITOR OUT [L, R]

150 Ω 10 kΩ Lines

+4 dB

(1.23 V)

+24 dB

(12.28 V)

Phone jack (TRS) (Balanced)

CH INSERT OUT 1–12

600 Ω 10 kΩ Lines

–2 dB

(616 mV)

+18 dB

(6.16 V)

Phone jack (TRS) (Unbalanced)

3. CH INSERT IN/OUT phone jacks are unbalanced. (Tip=OUTPUT, Ring=INPUT, Sleeve=GND).

2TR OUT [L, R]

600 Ω 10 kΩ Lines

–10 dBV

(316 mV)

+10 dBV

(3.16 V)

RCA Pin Jack (Unbalanced)

PHONES

100 Ω

8 Ω Phones 4 mW 25 mW

Stereo Phone Jack (TRS) (Unbalanced)

4. PHONES stereo phone jack is unbalanced (Tip=LEFT, Ring=RIGHT, Sleeve=GND).

40 Ω Phones 12 mW 75 mW

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha 01V96i Seite 61

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha 01V96i

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info