Bedienungsanleitung Yamaha 01X (Seite 17 von 156) (Englisch)

48716

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

01X Owner’s Manual

Controls and Connectors

Before UsingBasics SectionAppendix Getting StartedReference

e Channel knobs

These knobs mainly control the parameter settings/values

respectively assigned to them. They are also used to exe-

cute (YES) or cancel (NO) operation when a conﬁrmation

message appears (page 143). By simultaneously holding

down the [SHIFT] button and turning the desired knob,

you can quickly make broad value changes.

r [SEL] buttons

When the [SELECTED CHANNEL] button (page 19) is

on, these buttons enable you to select desired channels.

The [SEL] button indicator for the currently selected chan-

nel lights up. The channel selected by each [SEL] button

depends on the layer selected in the MIXER/LAYER sec-

tion (page 40). When a fader has been assigned to a Group

(page 101), the Group assignment can be temporarily

released by simultaneously holding down the [SEL] button

and moving the fader. In the Remote mode, the [SEL] but-

ton ﬂashes during automation touch-in. You can manually

activate touch-out by pressing the [SEL] button while it is

ﬂashing. The button can also be used to start touch-in

manually when the [AUTO EDIT] button is ON.

t [ON] buttons

These buttons turn the selected channels on or off. The

actual function differs depending on the status of the

[AUTO R/W] button, [SOLO] button or [REC RDY] but-

ton (!3, !4, !5).

y Channel faders

Depending on the settings of the MIXER/LAYER section

(page 40), these motorized faders adjust either the input

level of each channel or the output level of the AUX/REC

buses. By setting the Fader Touch Timeout parameter

(page 88) to an appropriate value, a touch-out function for

the faders can be emulated. See also !2[AUTO EDIT] but-

ton).

u Stereo fader

This motorized fader adjusts the ﬁnal output level of the

Stereo Out. By setting the Timeout parameter (page 88) to

an appropriate value, a touch-out function for the faders

can be emulated. See also !2[AUTO EDIT] button).

i [NAME/VALUE] button

Switches the display type between a channel/parameter/

value multi-function display or one that shows only the

parameter values. By holding down the [SHIFT] button

and pressing the [NAME/VALUE] button, you can also

enable and change the meter display (page 46).

o MONITOR/PHONES knob

Adjusts the level of the signal that is output from the

MONITOR OUT jacks and PHONES jack.

•You can monitor the output directly (monitor cascade) through

the connected speaker system/headphones (according to the

[MONITOR A/B] setting), if the stereo master output of the DAW

is set to the last two available channels (the last two numbered

channels speciﬁed with mLAN Auto Connector; refer to the sepa-

rate Installation Guide).

!0 DISPLAY [ / ] (Up/Down) buttons

For selecting the various display pages in order, as indi-

cated in the Function Tree (page 84).

!1 [PAGE SHIFT] button

Holding down the [PAGE SHIFT] button and pressing the

DISPLAY [ / ] (Up/Down) buttons allows you to jump

to certain pages (such as the ﬁrst in a particular parameter

category). (See the Reference section for details.)

!2 [AUTO EDIT] (Automation Edit) button

When this button is set to on in the remote mode, you can

manually activate touch-in (page 15) by using the [SEL]

button on each channel.

!3 [AUTO R/W] (Automation Read/Write)

button

When this button is set to on in the Remote mode, you can

switch the automation mode (page 15) by using the [ON]

button of each channel.

!4 [SOLO] button

When this button is set to on, you can solo individual chan-

nels by using the corresponding [ON] buttons. Solo can be

turned on for just one or any number of channels as desired

by pressing the appropriate [ON] buttons (t).

!5 [REC RDY] (Record Ready) button

When this button is set to on in the remote mode, you can

switch Record Ready for the desired channel on/off by

using the corresponding [ON] button.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha 01X Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info