Bedienungsanleitung Yamaha 02R96 version 2 (Seite 326 von 353) (Französisch)

559198

326

Zoom out

Zoom in

Vorherige Seite

1/353

Nächste Seite

326 Appendice C: MIDI

02R96 Version 2—Mode d’emploi

This data cannot be transmitted via Program Change to Studio Manager

since there is no guarantee that the contents of the tables will match. (Pa-

rameter Change messages will always be used.)

If [TABLE] is selected

Formula for converting Control values into parameter data:

paramSteps= paramMax - paramMin + 1;

add= paramWidth / paramSteps;

mod= paramWidth - add * paramSteps;

curValue= parm * add + mod / 2;

(1) When the assigned parameter can be set in 128 steps or less:

paramWidth = 127; rxValue = Control value;

(2) When the assigned parameter can be set in 128 through 16383 steps:

paramWidth = 16383;

(2-1) When both High and Low data are received:

rxValue = Control value (High) * 128 + Control value (Low);

(2-2) When only Low data is received:

rxValue = (curValue & 16256) + Control value (Low);

(2-3) When only High data is received:

rxValue = Control value (High) * 128 + (curValue & 127);

(3) When the assigned parameter can be set in 16384 through 2097151

steps:

paramWidth = 2097151;

(3-1) When High, Middle, and Low data are received:

rxValue = Control value (High) * 16384 + Control value (Middle) *

128 + Control value (Low);

(3-2) When only Low data is received:

rxValue = (curValue & 2097024) + Control value (Low);

(3-3) When only Middle data is received:

rxValue = (curValue & 2080895) + Control value (Middle) * 128;

(3-4) When only High data is received:

rxValue = (curValue & 16383) + Control value (High) * 16384;

(3-5) When Middle and Low data are received:

rxValue = (curValue & 2080768) + Control value (Middle) * 128 +

Control value (Low);

(3-6) When High and Low data are received:

rxValue = (curValue & 16256) + Control value (High) * 16384 +

Control value (Low);

(3-7) When High and Middle data are received:

rxValue = (curValue & 127) + Control value (High) * 16384 + Con-

trol value (Middle) * 128;

if ( rxValue > paramWidth)

rxValue = paramWidth;

param = ( rxValue - mod / 2) / add;

If [NRPN] is selected

*1) The second and subsequent STATUS need not be added during

transmission. Reception must be implemented so that recep-

tion occurs whether or not STATUS is present.

4. PROGRAM CHANGE (Cn)

Reception

If [Program Change ECHO] is ON, these messages are echoed.

If [Program Change RX] is ON and the [Rx CH] matches, these messages

will be received. However if [OMNI] is ON, they will be received regardless

of the channel. When a message is received, a Scene Memory will be re-

called according to the settings of the [Program Change Table].

Transmission

If [Program Change TX] is ON, this message is transmitted according to

the settings of the [Program Change Table] on the [Tx CH] channel when

a scene memory is recalled.

If the recalled scene has been assigned to more than one program number,

the lowest-numbered program number will be transmitted. Transmission

to Studio Manager using Program Change messages will not be performed

since there is no guarantee that the contents of the tables will match. (Pa-

rameter Changes will always be used.)

5 MIDI TIME CODE QUARTER FRAME(F1)

Reception

This is echoed if [OTHER COMMANDS ECHO] is ON.

Automix synchronizes this if the data is received at the port specified by the

TIME REFERENCE setting.

6. SONG POSITION POINTER (F2)

Reception

If this is received when the automix TIME REFERENCE setting is MIDI

CLOCK, the automix will move to the song position that was received.

7. TIMING CLOCK (F8)

Reception

If the automix TIME REFERENCE setting is MIDI CLOCK, this message

is used to synchronize automix. It is also used to control effects. This mes-

sage is transmitted 24 times per quarter note.

8. START (FA)

Reception

This message is received if the automix TIME REFERENCE setting is MIDI

CLOCK, and will start the automix. In actuality, automix will start when

the next TIMING CLOCK is received after receiving the START message.

9. CONTINUE (FB)

Reception

This message is received if the automix TIME REFERENCE setting is MIDI

CLOCK, and will cause automix to start from the current song position. In

actuality, automix will start when the next TIMING CLOCK is received af-

ter receiving the CONTINUE message.

10. STOP (FC)

Reception

This message is received if the automix TIME REFERENCE setting is MIDI

CLOCK, and will cause automix to stop.

STATUS 1011nnnn Bn

Control change

DATA 0nnnnnnn nn

Control number (0-95, 102-119)

0vvvvvvv vv

Control Value (0-127)

STATUS 1011nnnn Bn

Control changeDATA

01100010 62

NRPN LSB

0vvvvvvv vv

LSB of parameter number

STATUS 1011nnnn Bn

Control change*1

DATA 01100011 63

NRPN MSB

0vvvvvvv vv

MSB of parameter number

STATUS 1011nnnn Bn

Control change*1

DATA 00000110 06

MSB of data entry

0vvvvvvv vv

MSB of parameter data

STATUS 1011nnnn Bn

Control change*1

DATA 00100110 26

LSB of data entry

0vvvvvvv vv

LSB of parameter data

STATUS 1100nnnn Cn

Program change

DATA 0nnnnnnn nn

Program number (0-127)

STATUS 1100nnnn F1

Quarter frame message

DATA 0tttdddd td

Type & data

STATUS 11110010 F2

Song position pointer

DATA 0vvvvvvv vv

Song position LSB

0vvvvvvv vv

Song position MSB

STATUS 11111000 F8

Timing clock

STATUS 11111010 FA

Start

STATUS 11111011 FB

Continue

STATUS 11111100 FC

Stop

Yamaha 02R96 version 2 Seite 326

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha 02R96 version 2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info