Bedienungsanleitung Yamaha 03D (Seite 79 von 89) (Englisch)

517061

Zoom out

Zoom in

Vorherige Seite

1/89

Nächste Seite

74 03D Applications

Yamaha 02R & 03D Applications Guide

03D with Video Machine & DA-88

This application shows how the 03D can be used with a video machine and Tascam DA-88

for audio post-production and audio sweetening. Using only the SMPTE timecode from the

video machine, the DA-88 can generate MTC for the 03D. The eight digital tape returns and

18 Mic/Line inputs provide up to 26 inputs.

Connections

• The Tascam (CD8-TD) card must be screwed securely in place. Do not leave the screws

out after installation as the card will not be grounded correctly.

• The Tascam digital audio cable (PW-88DL) carries the eight tape sends and eight tape

returns.

• YGDAI digital outputs can be conﬁgured as bus outs, aux sends, input channel direct

outs, or stereo outs. So although the 03D is a four-bus mixer, assigning the four buses

and four aux sends, or the channel direct outs, to the YGDAI outputs allows eight-track

simultaneous recording. YGDAI output assignments are made on the D.out Setup page,

which can be located using the [DIO] button.

• YGDAI digital inputs feed 03D input channels 17 through 24.

• The optional SY-88 Sync Board is required. The DA-88 has a dedicated timecode track

and can output SMPTE timecode or MTC. In addition, a timecode offset can be

speciﬁed on the DA-88, so the 03D automix start time can be adjusted. The DA-88 also

has the ability to re-stripe the timecode track.

• The video house sync is connected to the Video In BNC connection on the DA-88.

03D Wordclock Setup

The 03D works as a wordclock slave. Any pair of YGDAI digital inputs can be selected as the

wordclock source. Use the [DIO] button to locate the D.in Setup page for wordclock

settings.

DA-88 Wordclock Setup

The DA-88 generates a wordclock signal referenced to the Video In signal (VIDEO). The

sampling rate is set when the DA-88 tape is formatted. This can be either 48 kHz or

44.1 kHz. After formatting, the sampling rate is determined by the formatted tape.

Notes

• The DA-88 must be powered up even when it is not being used. Failure to do so may

cause an intermittent pumping noise on the 03D.

• On the DA-88 rear panel, set the MACHINE ID to 0.

• The optional Tascam SY-88 Sync Board, available from Tascam, must be installed to use

SMPTE timecode and MTC. To use the MTC function, the SY-88 ﬁrmware must be

version 3.08 or higher.

• The rear panel of the SY-88 Sync Board has a DIP switch labeled MODE. Set DIP

switches 2 and 5 to ON (0). Set internal switch 8 on the SY-88 board marked S2 to ON.

• On the Tascam (CD8-TD) card there is a DIP switch that should be set to 16-bit. This is

the initial setting, but you should conﬁrm it. This switch is for use with Tascam High-Bit

recording applications.

• Tascam 25-pin digital audio cables PW-88DL (5 m) and PW-88D (1 m) are available

from Tascam

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha 03D Seite 79

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha 03D

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info