Bedienungsanleitung Yamaha 03DVEK (Seite 16 von 129) (Deutsch, Englisch, Französisch)

559201

Zoom out

Zoom in

Vorherige Seite

1/129

Nächste Seite

Display Pages 14

03D Video Edit Suite Software—Owner’s Manual

4 Display Pages

MIDI/HOST Page

This section explains the parameters on the MIDI/HOST page shown below. Use the [UTIL-

ITY] button to locate this page.

HOST INTERFACE—The STAND. and MULTI. switches under HOST INTERFACE are

the same as the STANDARD I/F and MULTIPORT switches on the regular 03D. The EDI-

TOR switch is used to activate the TO EDITOR port for use with a video editor.

TO EDITOR SETUP MEMORY—Three setup memories are available for storing settings

related to the TO EDITOR port. When the memory contents match the current settings,

these switches are grayed out. When a parameter setting is changed, the RECALL and STORE

switches can be used to recall the stored settings or store the new settings. The following

parameters are stored in these memories: FRAME TYPE, PARITY FLAG, FADER MODE,

INPUT LEVEL ADJUST OUTPUT level, and SOURCE/MACHINE ASSIGN settings.

INPUT LEVEL ADJUST—The OUTPUT level control determines the send level when the

fader is set to nominal (0 dB), and can be set from –48 dB to 0 dB in 1 dB steps. The input

level of the selected channel can be set manually or automatically so that the channel level

matches the speciﬁed output level. This setting is based on the assumption that the level will

not be changed using the faders, pan, EQ, or dynamics.

By reading the level of the test tone at the beginning of a reel (tape), the gain can be set auto-

matically so that the nominal level set by the user corresponds to the output level. The adjust-

able range is from –18 dB to +18 dB in 0.5 dB steps. If the level exceeds this range and cannot

be controlled, a warning message appears. For channels conﬁgured as a stereo pair, only the

left channel is used for level sensing. The level determined for the left channel is also applied

to the right channel. Due to circuitry limitations, the levels may vary between channels.

To automatically set the level for a channel, select the channel, use the cursor buttons to select

the AUTO switch, and then press the [ENTER] button.

To manually set the level for a channel, select the channel, use the cursor buttons to select

the MANUAL control, and then use the PARAMETER wheel.

When a channel level is set either manually or automatically, the corresponding Adjust

On/Off switch on the CH 1–16 or 17–24/Stin pages appears highlighted.

TO EDITOR—This parameter is used to enable and disable the TO EDITOR port, and must

be set to ENABLE for the 03D to respond to incoming ESAM II commands. Commands are

ignored when this is set to DISABLE.

FRAME TYPE—This parameter should be set to match the frame rate of the video. Options

are: ND (30 frames), DF (29.97 frames), 25 (25 frames), and 24 (24 frames). The 03D uses

this setting to calculate fade and delay times speciﬁed in frames.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha 03DVEK Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info