Bedienungsanleitung Yamaha A-S501 (Seite 16 von 146) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch)

555620

Zoom out

Zoom in

Vorherige Seite

1/146

Nächste Seite

14 En

TROUBLESHOOTING

No sound. Playback has been stopped on the

connected component.

Turn the component on and start playback.

No appropriate input source has been

selected.

Select an appropriate input source with the INPUT

selector on the front panel (or one of the Input

selector buttons on the remote control).

The SPEAKERS selector is not set

properly.

Set the corresponding SPEAKERS selector to A, B or

A+B BI-WIRING position.

The output audio source setting on the

connected component is not PCM.

Only PCM audio sources can be played via the

DIGITAL (OPTICAL/COAXIAL) jacks of this unit.

Set the output audio source of the connected

component to PCM.

The sound suddenly

goes off.

The automatic power down function has

activated.

Confirm that there are no other issues causing this

problem, and then turn this unit on again.

To turn off the AUTO POWER STANDBY function,

set the AUTO POWER STANDBY switch to OFF on

the rear panel.

Only the speaker on

one side can be

heard.

Incorrect cable connections. Connect the cables properly. If the problem persists,

the cables may be defective.

Incorrect setting for the BALANCE

control.

Set the BALANCE control to the appropriate

position.

There is a lack of bass

and no ambience.

The + and – wires are connected in

reverse at the amplifier or the speakers.

Connect the speaker wires to the correct + and –

phase.

A “humming” sound

can be heard.

Incorrect cable connections. Connect the audio plugs firmly. If the problem

persists, the cables may be defective.

9, 10

No connection from the turntable to the

GND terminal.

Make the GND connection between the turntable and

this unit.

The volume level

cannot be increased,

or the sound is

distorted.

The component connected to the LINE 2

REC or LINE 3 REC jacks of this unit is

turned off.

Turn on the power of the component.

—

The sound is

degraded when

listening with

headphones

connected to a CD

player connected to

this unit.

This unit is turned off or is in standby

mode.

Turn on the power of this unit.

—

The sound level is

low.

Sound is muted. Press MUTE on the remote control or rotate the

VOLUME control.

The loudness control function is

operating.

Turn down the volume, set the LOUDNESS control

to the FLAT position, and then adjust the volume

again.

The volume level is

low while playing a

record.

The turntable is connected to the jacks

other than the PHONO jacks.

Connect the turntable to the PHONO jacks.

The record is being played on a turntable

with an MC cartridge.

Use a turntable equipped with an MM cartridge.

Using the BASS,

TREBLE, BALANCE

and LOUDNESS

controls does not

affect the sound.

The CD DIRECT function or the PURE

DIRECT function is turned on.

The CD DIRECT function or the PURE DIRECT

function must be turned off to use those controls.

Problem Cause Remedy

See

page

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha A-S501 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info