Bedienungsanleitung Yamaha A5000 (Seite 45 von 296) (Englisch)

48720

Zoom out

Zoom in

Vorherige Seite

1/296

Nächste Seite

ESSENTIAL PROCEDURES

● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● A5000/A4000 • Chapter 2 Sampler Basics & Essential Procedures 45

3. Specify the Loop Mode

Use Knob 1 to highlight the third function line on the display (“Auto” & “LpMode”), and use Knob 3

to select the desired Loop Mode. The available loop modes are listed below:

4. Specify the Loop Start & End Addresses

Use Knob 1 to highlight the second function line on the display (“Loop”), then use Knob 2 and Knob

3 to specify the Loop Start and End addresses, respectively. Dotted vertical lines in the waveform dis-

play show the currently selected Start and End points.

If you need coarser or ﬁner adjustment, use Knob 4 to select the digit in the Start and End values

which will be directly adjusted by Knobs 2 and 3. Your options are x1, x10, x100, x1000, and x10000.

The position of the inverse block cursor in the address values shows the digit currently being adjusted.

You can hear how the edited sample sounds at any point during this process by pressing the [AUDI-

TION] button.

• Note that the Loop values cannot be set “outside” the Wave Start and End points. Obviously, the

Loop Start point cannot be set earlier than the Wave Start Point, and the Loop End Point cannot

be set later than the Wave End Point.

• You can change the units used for trim and loop point speciﬁcation by scrolling down to the “End-

Type” parameter and using Knob 2 to select the desired unit: “Address”, “Length”, “Time”, or

“Beat”. See page 124 for details on this feature.

• The speciﬁed Loop Start and End points are saved with the sample data.

Handy Auto-addressing Functions ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●

Sometimes, setting the optimum Wave and Loop points can be a tricky business. Unless your Start and

End points are set precisely to the right points on the sample waveform, you can end up with annoying

clicks and noise. The A5000/A4000 provides a number of auto-addressing functions that can make it

easy to set precise Start and End points.

Use Knob 1 to highlight the third function line (“Auto” and “LpMode”), then use Knob 2 to select the

Auto mode that best suits you purpose (see list below).

– – → No loop

– →O Continuous loop; the loop will continue to play until the note(s) is released, then the remain-

der of the loop will play and playback will stop.

→O→ Loop to release: the loop will play until the note(s) is released, then the remaining portion of

the sample will play.

← – – No loop; reverse playback.

One→ No loop one-shot. The sample plays through to the end regardless of note-off.

One← No loop; reverse one shot. The sample plays through to the end backwards, regardless of

note-off.

off No auto-addressing.

LengLock “Length Lock”. When this mode is selected the length of the sample or loop will be precisely

maintained when either the Start or End point is changed. For example, if you adjust the

Loop Start address, the Loop End address will change automatically to maintain a constant

loop length.

Zero When this mode is selected only addresses which correspond to zero-crossing points on the

waveform can be selected. This makes it easy to trim or loop a waveform so that no clicks

are produced at the beginning or end of the sample.

Snap When “Snap” is selected, only addresses corresponding to points on the waveform which

are at exactly the same level as the opposing point can be selected. For example, if you have

set the Start point of a loop, then the End point will always be at precisely the same level as

the Start point. This mode can make it easy to set smooth, noise-free loops.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha A5000 Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha A5000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info