Bedienungsanleitung Yamaha AN1X (Seite 75 von 122) (Englisch)

48724

Zoom out

Zoom in

Vorherige Seite

1/122

Nächste Seite

● Source

The Source setting determines which controller (by

Control Change number) is assigned to control the

corresponding Parameter.

You can set the source by Control Change number or by controller name, as

shown in the Settings listed below.

Settings:

CcOff: No controller assigned.

CC1 ~ 95: Selects the Source controller according to Control

Change number, when received by on-board controllers or

incoming MIDI messages.

AT (After Touch): For controlling with keyboard After Touch.

PB (Pitch Bend): For controlling with the Pitch Bend wheel.

KyTrk (Key Track): For controlling with note number

messages generated by pressing the keys.

Vel (Velocity): For controlling with keyboard velocity, or the

strength with which you strike the keys.

KyRnd (Key Random): For controlling with random note

number messages generated by pressing the keys.

A.MW (Assign Modulation Wheel): For controlling with

the Modulation Wheel, and/or by incoming MIDI messages

with the same Control Change number as assigned to the

MW.

A.FV (Assign Foot Volume): For controlling with a

connected Foot Volume controller, and/or by incoming MIDI

messages with the same Control Change number as assigned

to the FV.

A.FC (Assign Foot Control): For controlling with a

connected foot controller, and/or by incoming MIDI messages

with the same Control Change number as assigned to the FC.

A.FS (Assign Footswitch): For controlling with a

connected Footswitch, and/or by incoming MIDI messages

with the same Control Change number as assigned to the FS.

A.RbX (Assign Ribbon Controller-X): For controlling

with the Ribbon controller X-axis (left and right), and/or by

incoming MIDI messages with the same Control Change

number as assigned to the RbX.

A.RbZ (Assign Ribbon Controller-Z): For controlling

with the Ribbon controller Z-axis (push), and/or by incoming

MIDI messages with the same Control Change number as

assigned to the RbZ.

Kn1~8 (Knob 1 ~ 8): For controlling with a specified

CONTROL knob (when KNOB PARAMETER GROUP

[ASSIGN] is on).

Depending on selected Parameter, the available Source for assignment may be

different. For details of available parameters, see the table of Control Matrix

parameters in the separate Data List book.

You cannot assign the same Source controller and Parameter to more than one

set. If you attempt to, lower-numbered sets will take priority, and "– – –" will

appear in the LCD for higher-numbered sets.

When you select [RIBBON] controller "A.RbX" as the "Source" controller and Pitch

Up/Pitch Down as the "Parameter", the [RIBBON] controller value will be reset to

the center position when you release your finger from the [RIBBON]. The sets

with different Parameters (other than Pitch Up/Pitch Down) keep the position at

which you release your finger.

● Depth

The Depth setting determines the control range of the

Source controller.

Settings:

Depending on the selected Parameter, the available settings

may be different. For details, see the table of Control Matrix

parameters in the separate Data List book.

Direct Control Function

When Depth "Dirct" is selected (0 setting), the Direct Control

function is activated, and you can directly edit the parameter

assigned to the controller within its original range.

Relationship Between Control Matrix And

Utility Control Assign Function

There are two types of Control Change assignment

functions—the Control Matrix and the Utility Control Assign

function. Between the Control Matrix and Utility Control

Assign function (see page 95), you can configure a

sophisticated controller setup to control specific parameters of

the internal tone generator and an external tone generator at

the same time by the eight CONTROL knobs and other

controllers. Control Change assignments made in the Utility

Control Assign function are sent to both MIDI [OUT] as well

as the Control Matrix, where it can be rerouted at will before

reaching the internal tone generator. External Control

Change signals received at MIDI [IN] can be routed through

the Control Matrix to control the AN1x tone generator

parameter of your choice.

AN1x Tone Generator

MIDI IN

MIDI OUT

Utility Control

Assign

Control Matrix

Control Signal Flow

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha AN1X Seite 75

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha AN1X

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info