Bedienungsanleitung Yamaha AN1X (Seite 110 von 122) (Englisch)

48724

110

Zoom out

Zoom in

Vorherige Seite

1/122

Nächste Seite

110

Pan (Control #010)

Messages which control the stereo panning position of

each voice (for stereo output).

Setting the value to 127 positions the sound to the far

right and 0 positions the sound to the far left.

Expression (Control #011)

Messages which control intonation expression of each

voice during performance.

Setting the value to 127 produces maximum volume

and 0 results in volume off.

Sustain Switch (Control #064)

Messages which control sustain on/off.

Setting the value between 64 - 127 turns the sustain

on, between 0 - 63 turns the sustain off.

Portamento Switch (Control #065)

Messages which control portamento on/off.

Setting the value between 64 -127 turns the

portamento on, between 0 - 63 turns the portamento

off.

Harmonic Content (Control #071)

Messages which adjust the VCF resonance set for each

voice.

Higher values will result in a more characteristic,

resonant sound. Depending on the voice, the effective

range may be narrower than the range available for

adjustment.

Release Time (Control #072)

Messages which directly adjust the AEG release time

set for each voice.

Attack Time (Control #073)

Messages which directly adjust the AEG attack time set

for each voice.

Brightness (Control #074)

Messages which directly adjust the VCF cutoff

frequency set for each voice.

Lower values will result in a softer sound. Depending

on the voice, the effective range may be narrower than

the range available for adjustment.

Effect1 Depth (Reverb) (Control

#091)

Messages which adjust the send level for the Reverb

effect.

Effect3 Depth (Variation [Chorus])

(Control #093)

Messages which adjust the dry/wet balance for the

Chorus Variation Effect.

Effect4 Depth (Delay Depth) (Control

#094)

Messages which adjust the send level for the Delay

effect.

Data Increment (Control #096)

Decrement (Control #097) for RPN

Messages which increase or decrease the MSB value

of pitch bend sensitivity.

You must assign one of those parameters using the RPN

in the external device in advance.

The data byte is ignored.

When the maximum value or minimum value is

reached, the value will not be incremented or

decremented further. (Incrementing the fine tune will not

cause the coarse tune to be incremented.)

RPN (Registered Parameter Number)

LSB (Control #100)

RPN (Registered Parameter Number)

MSB (Control #101)

Messages which offset, or add or subtract values from

a voice's pitch bend sensitivity.

First send the RPN MSB and RPN LSB to specify the

parameter which is to be controlled. Then use Data

Increment/Decrement to set the value of the specified

parameter.

Note that once the RPN has been set for a channel,

subsequent data entry will be recognized as the same

RPN's value change. Therefore after you use the RPN,

you should set a Null (7FH, 7FH) value to avoid an

unexpected result.

Messages which can be received are as follows:

RPN MSB RPN LSB PARAMETER

00 00 Pitch Bend Sensitivity

00 01 Fine Tune

00 02 Coarse

7F 7F Null

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha AN1X Seite 110

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha AN1X

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info