Bedienungsanleitung Yamaha AX-496 (Seite 7 von 100) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch)

557296

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

English

E-5

Connecting speakers

Connect the SPEAKERS terminals to your speakers with

the wire with the proper gauge (keep it as short as

possible). If the connections are faulty, no sound will be

heard from the speakers. Make sure that the + and –

polarity markings of the speaker wires are observed and set

correctly. If these wires are reversed, the sound will be

unnatural and lack bass.

Caution

Do not let the bare speaker wires touch each other or

any metal part of this unit. This could damage this unit

or the speakers, or both.

How to Connect:

Red: positive (+)

Black: negative (–)

1 Loosen the knob.

2 Insert the bare wire.

[Remove approx.

10 mm (3/8”)

insulation from the

speaker wires.]

3 Tighten the knob

and secure the wire.

● One or two speaker systems can be connected to this

unit. If you use only one speaker system, connect it to

either the SPEAKERS A or B terminals.

● Use speakers with the specified impedance shown on the

rear of this unit.

● <Australia, China and General models only>

Banana Plug connections are also possible. Simply

insert the Banana Plug connector into the corresponding

terminal.

Rear panel parts

IMPEDANCE SELECTOR switch

WARNING

Do not change the IMPEDANCE SELECTOR switch

setting while the power to this unit is on, otherwise

this unit may be damaged.

If this unit fails to turn on when the POWER switch is

pressed:

The IMPEDANCE SELECTOR switch may not be set to

either end. If so, set the switch to either end when this

unit’s power supply is completely cut off.

Select the position whose

requirements your speaker

system meets.

(Right position)

If you use one pair of speakers, the impedance of

each speaker must be 4Ω or higher.

If you use two pairs of speakers, the impedance of

each speaker must be 8Ω or higher.

(Left position)

If you use one pair of speakers, the impedance of

each speaker must be 6Ω or higher.

If you use two pairs of speakers, the impedance of

each speaker must be 12Ω or higher.

AC OUTLET(S) (SWITCHED)

(Europe, China and General models)

...................................................... 3 SWITCHED OUTLETS

(U.K. and Australia models)............. 1 SWITCHED OUTLET

Use these to connect the power cords of your components

to this unit.

The power to the SWITCHED outlets is controlled by this

unit’s POWER or STANDBY/ON switch. These outlets will

supply power to any connected unit whenever this unit is

turned on.

The maximum power (total power consumption of

components) that can be connected to the SWITCHED AC

OUTLETS is 100W.

GND terminal (For turntable use)

Connecting the ground wire of the turntable to the GND

terminal will normally minimize hum, but in some cases

better results may be obtained with the ground wire

disconnected.

A OR B : 6

Ω

MIN. /SPEAKER

A B : I2

Ω

MIN. /SPEAKER

A OR B : 4

Ω

MIN. /SPEAKER

A B : 8

Ω

MIN. /SPEAKER

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha AX-496 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info