Bedienungsanleitung Yamaha CDRD651 (Seite 29 von 33) (Englisch)

18179

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

E-28

ADDITIONAL INFORMATION ...................................................

CD-Recorder System Notes and

Limitations

■ About track length and number

• The CD specifications state that the minimum length of a

CD track must be 4 seconds. If a recording is stopped

while the track is less than 4 seconds long, the unit will

record silence until the 4 second track length

requirement has been reached, and then stop recording.

• CDs can be recorded with up to 99 tracks on them.

Recording will be automatically stopped if the 99 track

limit is exceeded. Once 99 tracks have been recorded,

no further recording is possible even if time is remaining

on the disc.

■ About source sampling rate conversion

When recording an analog source (such as an LP or

cassette), this unit converts the analog signals to a 44.1 kHz

digital signal before recording them onto the CD-R or CD-

RW disc.

When recording a digital source, this unit converts the

digital signals to 44.1 kHz for recording onto the CD-R or

CD-RW disc. This unit can record 32, 44.1 and 48 kHz

digital signals.

■ When making digital recordings from DAT

When recording from a DAT source, make sure that the start

IDs on DAT tapes are in positions slightly before the actual

audio begins.

DAT tapes that are originally recorded using the DAT

recorder’s auto ID function record the start ID slightly after

the actual recording begins. Because this recorder uses the

start ID on the DAT to indicate the transition between tracks,

the following problems may occur during synchronized

recording (single track or ALL track).

• The beginning of the audio on a track is not recorded.

• A new track number is created slightly after the

beginning of a new track.

• The beginning of the next track is recorded at the end

of a recording.

To avoid these potential problems, it is recommended to

perform manual recording of DAT sources. For more

information on DAT operations, refer to the operating

instructions provided with the DAT recorder.

■ When making a digital copying from a DTS-

Select CD DIRECT mode to make a digital copying from a

DTS-CD.

SCMS Copy Protection

As a digital audio component, this CD recorder conforms

with the Serial Copy Management System (SCMS)

standards. The Serial Copy Management System restricts

copies made by recording digital signals to first generation

copies only.

● Rule 1

You can record digital program sources onto a

recordable CD disc using a DIGITAL IN jack to create a

first generation digital copy. You cannot, however,

record from this recorded CD disc to another recordable

CD disc using a DIGITAL IN jack.

● Rule 2

A CD disc that was recorded using the ANALOG jacks

can be recorded onto other digital recording media

using a DIGITAL OUT jack to create a first generation

digital copy. You cannot, however, make a second

generation copy using a DIGITAL OUT jack.

Second generation digital copy cannot be made because

this unit is designed to conform with SCMS standards.

However, when second generation digital copy is not

possible, this unit automatically changes the setting to

analog recording to complete recording.

In this case, set “SCMS Mode” in the set menu to ANALOG

Copy. (See page 11.)

Before setting the recording level by using the ANALOG

REC LEVEL knob, start the source CD on the disc tray A

first, and then press REC for the disc tray B.

■ Recording of non-audio signals

This unit is designed exclusively for recording audio

signals. Non-audio signals from sources such as CD-ROM

cannot be recorded. Recording is possible only when the

input digital signal is an audio signal. Similarly when a

digital signal contains graphic or character information such

as a CD+graphics disc, the graphic or character

information is not recorded.

ADDITIONAL INFORMATION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha CDRD651 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha CDRD651

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info