18181

Yamaha CDRHD1300E Seite 98

98
Zoom out
Zoom in
Vorherige Seite
1/106
Nächste Seite
E-92
SYMPTOM
This unit does not turn on
when POWER is pressed.
Playback does not begin
with the CD loaded.
Playback is delayed, or
begins at the wrong place.
Recording/copying is not
possible.
Some vibration and rotation
noise are created during the
copying.
Continuous recording
cannot be made on a disc on
the HDD beyond 100
minutes.
The beginning of the track
is missing during the
playback when this unit is
connected digitally to an
amplifier.
The sound is missing when
this unit switches one disc
to another.
A CD-R or CD-RW that has
been recorded with this unit
cannot be played on the
other CD player or DVD
player.
Sound “skips”.
This unit makes noise.
If this unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures
suggested. If they cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your
authorized YAMAHA dealer or service center for assistance.
CAUSE
The power cable is not completely connected.
There is moisture on the laser pick-up.
The CD has been loaded upside down.
The CD is dirty.
The CD may be scratched or damaged.
The CD-R or CD-RW disc has been finalized.
The CD-R or CD-RW disc that has completed
recording is loaded.
INPUT is not correctly set.
Further digital recording or copying has been
attempted from the digitally copied sources.
There is not enough available space left or 99
tracks have already been recorded on the disc.
There is no available space on the HDD.
If the power cable was unplugged or there
was a power outage during recording, the
recorded material may be lost.
The CD-R or CD-RW disc is dirty or
damaged.
The HDD is not installed properly.
This unit copies by rotating the CD, CD-R or
CD-RW disc at high speed.
The maximum recordable time for a disc on
the HDD is 99 minutes 59 seconds.
The tracks that have different emphases have
been played.
The titles appear on the display during the
playback of the part that has been recorded
stretching over the two discs.
Your CD or DVD player is not compatible
with CD-R or CD-RW discs.
The CD-R or CD-RW disc has not been
finalized.
This unit and/or the component connected is
being subjected to vibration or impact.
The CD is dirty.
Connection has not correctly been made.
REMEDY
Securely connect the power cable.
Turn the power of this unit and wait 20 to 30 minutes
before trying to play.
Reload the CD with the label side facing up.
Clean the CD.
Check the CD carefully. Replace it if necessary.
Load a recordable CD that has not been finalized yet.
Load a recordable CD.
Set INPUT to the correct position according to the input
signal.
Switch to ANALOG to make a recording.
Load a recordable disc (for a CD-R or CD-RW disc).
Select the other discs (for the HDD).
Erase the space not being used to create available space on
the HDD for further recording.
If the recording of a CD-RW disc is interrupted, try
recording again from the beginning. When the recording of
a CD-R disc is interrupted, start recording over again with
a disc that can be recorded on.
Clean or replace the CD-R or CD-RW disc.
Install the HDD properly following the attached instruc-
tion.
Lower the copying speed to decrease vibration and rotation
noise.
Regardless of the recording mode, the recording will be
performed continuously to the next available disc after the
recording has been performed to one disc for its maximum
length.
Connect to the amplifier using the ANALOG LINE OUT
(PLAY) jacks.
Press TEXT/TIME to switch the display to the indication
of time.
Use a CD or DVD player compatible with CD-R or CD-
RW discs.
Finalize the CD-R or CD-RW disc.
Relocate the unit. (This is not possible if the skipping
sound is already on the recording due to vibrations or
impact that occurred during recording.)
Clean the CD.
Properly connect the audio pin cables. Replace the audio
cables.
TROUBLESHOOTING
110_HD1300(E)84-94 02.6.24, 6:52 PM92
… 98 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yamaha CDRHD1300E wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Yamaha CDRHD1300E

Yamaha CDRHD1300E Bedienungsanleitung - Deutsch - 100 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info