Bedienungsanleitung Yamaha CLP-370 (Seite 75 von 108) (Englisch)

590641

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

Connections

CLP-370/340/330, CLP-S308/S306 Owner’s Manual

ENGLISH

Connecting a Personal Computer

By connecting a computer to the Clavinova’s USB [TO HOST] terminal, you can transfer data

between the instrument and the computer via MIDI. To do this, install the USB-MIDI driver and

Musicsoft Downloader software (refer to the included “Accessory CD-ROM Installation Guide”).

CAUTION

When connecting the Clavinova to a personal computer, ﬁrst turn off the power to both the Clavi-

nova and the computer before connecting any cables. After making connections, turn on the

power to the computer ﬁrst, then to the Clavinova.

CAUTION

If you are not using the connection between the Clavinova and your computer, you must discon-

nect the cable from the USB [TO HOST] terminal. The Clavinova may not operate correctly if a

cable is left connected.

Use a USB cable to connect the USB port on your computer to the USB [TO HOST]

terminal on the Clavinova.

TERMINOLOGY

Driver:

A driver is software that provides

a data-transfer interface between

the computer’s operating system

and a connected hardware

device. You need to install a USB

MIDI driver to connect the com-

puter and the instrument.

NOTE

• The instrument will begin trans-

mission a short time after the

USB connection is made.

• When using a USB cable to

connect the instrument to your

computer, make the connec-

tion directly without passing

through a USB hub.

• For information on setting up

your sequence software, refer

to the owner’s manual of the

relevant software.

Precautions when using the USB [TO HOST] terminal

When connecting the computer to the USB [TO HOST] terminal, make sure to observe the

following points. Failing to do so risks freezing the computer and corrupting or losing the

data. If the computer or the instrument freezes, restart the application software or the com-

puter OS, or turn the power to the instrument off then on again.

CAUTION

• Use an AB type USB cable of less than about 3 meters.

• Before connecting the computer to the USB [TO HOST] terminal, exit from any power-sav-

ing mode of the computer (such as suspended, sleep, standby).

• Before turning on the power to the instrument, connect the computer to the USB [TO

HOST] terminal.

• Execute the following before turning the power to the instrument on/off or plugging/

unplugging the USB cable to/from the USB [TO HOST] terminal.

- Quit any open application software on the computer.

- Make sure that data is not being transmitted from the instrument. (Data is transmitted

only by playing notes on the keyboard or playing back a song.)

• While the computer is connected to the instrument, you should wait for six seconds or

more between these operations: (1) when turning the power of the instrument off then on

again, or (2) when alternately connecting/disconnecting the USB cable.

USB

TO DEVICE

TO HOST

USB [TO HOST] terminal

USB cable

Computer

Instrument

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha CLP-370 Seite 75

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha CLP-370

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info