Bedienungsanleitung Yamaha CLP-611 (Seite 54 von 71) (Französisch)

590832

Zoom out

Zoom in

Vorherige Seite

1/71

Nächste Seite

(52)~(68) Organ Combination data 2

(69)~(85) Organ Combination data 3

(86)~(102) Organ Combination data 4

(103)~(119) Organ Combination data 5

(120)~(136) Organ Combination data 6

(137)~(153) Organ Combination data 7

(154)~(170) Organ Combination data 8

* The Clavinova does not accept requests to

transfer panel data.

7. System Exclusive Messages

(Universal System Exclusives)

1) Universal Realtime Message

[F0H] → [7FH] → [XnH]→ [04H]→ [01H] →

[

RRRR

H] → [mmH] → [F7H]

MIDI Master Volume

* This message changes the volume for all

channels at the same time.

* Receipt of this message affects the volume on

the MIDI receiving channel(s) only. Panel

volume does not change.

F0H: Exclusive status

7FH: Universal realtime

7FH: ID of target device

04H: Sub-ID #1 (Device control message)

01H: Sub-ID #2 (Master Volume)

RRRR

H: Volume LSB

mmH: Volume MSB

F7H: End of Exclusive

-or-

F0H: Exclusive status

7FH: Universal realtime

XnH: X is ignored; n=0~F

04H: Sub-ID #1 (Device control message)

01H: Sub-ID #2 (Master Volume)

RRRR

H: Volume LSB

mmH: Volume MSB

F7H: End of Exclusive

2) Universal Non-Realtime Message

(GM ON)

[F0H] → [7EH] → [XnH]→ [09H]→ [01H] →

[F7H]

GM (General MIDI) Mode ON

F0H: Exclusive status

7EH: Universal non-realtime

7FH: ID of target device

09H: Sub-ID #1 (General MIDI message)

01H: Sub-ID #2 (General MIDI ON)

F7H: End of Exclusive

-or-

F0H: Exclusive status

7EH: Universal non-realtime

XnH: X is ignored; n=0~F

09H: Sub-ID #1 (General MIDI message)

01H: Sub-ID #2 (General MIDI ON)

F7H: End of Exclusive

* Receipt of the GM ON message causes MIDI

parameters to reinitialize. Allow sufficient time

for processing to execute (about 50 msec) before

sending the Clavinova another message.

8. System Exclusive Messages

(XG Standard)

1) XG Native Parameter Change

[F0H] → [43H] → [1nH]→ [4CH]→ [hhH] →

[mmH] → [

RRRR

H] → [ddH] ... → [F7H]

F0H: Exclusive status

43H: Yamaha

1nH: Device No.

(If transmission, n=0. If reception, n=0~F.)

4CH: XG model ID

hhH: Address High

mmH: Address Mid

RRRR

H: Address Low

ddH: Data

: :

F7H: End Of Exclusive

2) Bulk Dump (Receive only)

[F0H] → [43H] → [0nH]→ [4CH] → [aaH] →

[bbH] → [hhH] → [mmH] → [

RRRR

H] → [ddH] →

... → [ccH] → [F7H]

F0H: Exclusive status

43H: Yamaha

0nH: Device No. (n=0~F.)

4CH: XG model ID

aaH: Byte count

bbH: Byte count

hhH: Address High

mmH: Address Mid

RRRR

H: Address Low

ddH: Data

: :

ccH: Checksum

F7H: End Of Exclusive

* Receipt of this message causes reinitialization of

relevant parameters and Control Change values.

Allow sufficient time for processing to execute

(about 50 msec) before sending the Clavinova

another message.

* XG Native Parameter Change message may

contain two or four bytes of parameter data

(depending on the parameter size).

* For information about the Address and Byte

Count values, refer to Table 1 below. Note that

the table’s Total Size value gives the size of a

bulk block. Only the top address of the block

(00H, 00H, 00H) is valid as a bulk data address.

* Transmission of excessive bulk-data length may

cause error at the receiving side. Keep message

length within 512 bytes. If you need to send

more than 512 bytes, break the transmission into

multiple parts and allow at least 120 msec

between each transmission.

MIDI Parameter Change (SYSTEM)

Address (H) Size (H) Data (H) Parameter Description Default (H)

00 00 00 4 020C~05F4 MASTER TUNING -50~+50 [cents] 00 04 00 00 * Value below 020CH selects -50 cents.

01 1st byte bits (3~0) → Bits 15~12 400 Value above 05F4H selects +50 cent.

02 2nd byte bits (3~0) → Bits 11-8

03 3rd byte bits (3~0) → Bits 7-4

4th byte bits (3~0) → Bits 3-0

04 1 00~7F MASTER VOLUME 0~127 7F

05 1

06 1 34~4C TRANSPOSE -12~+12 [semitones] 40 *

Values 28H to 33H select -12 to -1, respectively.

7E 0 XG SYSTEM ON 00=XG System ON

Values 4DH to 58H select +1 to +12, respectively.

7F 0

RESET ALL PARAMETERS

00= ON (Receive only)

Total Size 7

MIDI Parameter Change (EFFECT 1)

* For a listing of REVERB, CHORUS, and VARIATION type numbers, refer to the Effect MIDI maps.

Address (H) Size (H) Data (H) Parameter Description Default (H)

02 01 00 2 00~7F REVERB TYPE MSB Refer to the Effect MIDI Map. 01 (=HALL 1)

00~7F REVERB TYPE LSB 00: Basic Type 00

0C 1 00~7F REVERB RETURN -∞dB…0dB…+6dB (0…64…127) 40

02 01 40 2 00~7F VARIATION TYPE MSB Refer to the Effect MIDI Map. 00 (No effect)

00~07F VARIATION TYPE LSB 00: Basic Type 00

Note: “VARIATION TYPE” corresponds to the Clavinova’s panel-set effect type.

MIDI Parameter Change (Multipart)

Address (H) Size (H) Data (H) Parameter Description Default (H)

08 nn 11 1 00~7F DRY LEVEL 0~127 7F

nn= Part number

CLP-811/611 MIDI Data Format/MIDI-Datenformat/Format de données MIDI/Formato de datos MIDI

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha CLP-611 Seite 54

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha CLP-611

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info