Bedienungsanleitung Yamaha CLP-880 (Seite 45 von 72) (Deutsch)

593319

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

CLP-880/860/840/820/820S

(2) Universal Non-Realtime Message (GM 0n)

General MIDI Mode On

Data format: [F0H] -> [7EH] -> [XnH] -> [09H] -> [01H] ->

[F7H]

F0H = Exclusive status

7EH = Universal Non-Realtime

7FH = ID of target device

09H = Sub-ID #1=General MIDI Message

01H = Sub-ID #2=General MIDI On

F7H = End of Exclusive

F0H = Exclusive status

7EH = Universal Non-Realtime

XnH = When received, n=0~F.

X = don’t care

09H = Sub-ID #1=General MIDI Message

01H = Sub-ID #2=General MIDI On

F7H = End of Exclusive

When the General MIDI mode ON message is received, the MIDI

system will be reset to its default settings.

This message requires approximately 50ms to execute, so suffi-

cient time should be allowed before the next message is sent.

8. SYSTEM EXCLUSIVE MESSAGES (XG Standard)

(1) XG Native Parameter Change

Data format: [F0H] -> [43H] -> [1nH] -> [4CH] -> [hhH] ->

[mmH] -> [llH] -> [ddH] -> [F7H]

F0H = Exclusive status

43H = YAMAHA ID

1nH = When received, n=0~F.

When transmitted, n=0.

4CH = Model ID of XG

hhH = Address High

mmH = Address Mid

llH = Address Low

ddH = Data

F7H = End of Exclusive

Data size must match parameter size (2 or 4 bytes).

When the XG System On message is received, the MIDI system

will be reset to its default settings.

The message requires approximately 50ms to execute, so suffi-

cient time should be allowed before the next message is sent.

(2) XG Native Bulk Data (reception only)

Data format: [F0H] -> [43H] -> [0nH] -> [4CH] -> [aaH] ->

[bbH] -> [hhH] -> [mmH] -> [llH] ->

[ddH] ->...-> [ccH] -> [F7H]

F0H Exclusive status

43H YAMAHA ID

0nH When received, n=0~F.

When transmitted, n=0.

4CH Model ID of XG

aaH ByteCount

bbH ByteCount

hhH Address High

mmH Address Mid

llH Address Low

ddH Data

| |

ccH Check sum

F7H End of Exclusive

• Receipt of the XG SYSTEM ON message causes reinitialization

of relevant parameters and Control Change values. Allow suffi-

cient time for processing to execute (about 50 msec) before

sending the Clavinova another message.

• XG Native Parameter Change message may contain two or four

bytes of parameter data (depending on the parameter size).

• For information about the Address and Byte Count values, refer

to Table 1 below. Note that the table’s Total Size value gives the

size of a bulk block. Only the top address of the block (00H, 00H,

00H) is valid as a bulk data address.

9. SYSTEM EXCLUSIVE MESSAGES

(Clavinova MIDI Format)

Data format: [F0H] -> [43H] -> [73H] -> [xxH] -> [nnH] ->

[F7H]

F0H = Exclusive status

43H = Yamaha ID

73H = Clavinova ID

xxH = Product ID (CLP-880/860/840/820/820S common ID:

50H or CLP common ID: 01H)

nnH = Substatus

nn Control

02H Internal MIDI clock

03H External MIDI clock

06H Bulk Data (the bulk data follows 06H)

F7H = End of Exclusive

* When nn=02H or 03H, Clavinova common ID (01H) is

recognized as well as 50H.

BULK DUMP FORMAT

F0H, 43H, 73H

xxH =Product ID (CLP-880: 56H, CLP-860:

54H, CLP-840: 53H, CLP-820/820S:

52H)

06H =Bulk ID

05H =Sequence data

0nH, 0nH, 0nH, 0nH, 0nH, 0nH, 0nH, 0nH =Data length

[BULK DATA] =

[CHECK SUM (1byte)] = 0-sum (BULK DATA)

F7H = End of Exclusive

10. SYSTEM EXCLUSIVE MESSAGES (Special Control)

Data format: [F0H] -> [43H] -> [73H] -> [xxH] -> [11H] ->

[0nH] -> [ccH] -> [vvH] -> [F7H]

F0H = Exclusive status

43H = Yamaha ID

73H = Clavinova ID

50H =

CLP-880/860/840/820/820S common ID

11H = Clavinova special control

0nH = Control MIDI change (n=channel number)

cc = Control number

vv = Value

F7H = End of Exclusive

Control 0n ccH vvH

Split Point Always 00H 14H 14H :

Split Key Number

(CLP-880/860)

Metronome Always 00H 1BH 00H : off

01H : –

02H : 2/4

03H : 3/4

04H : 4/4

06H : 6/4

7FH : No accent

Damper Level ch: 00H-0FH 3DH (Sets the Damper Level

for each channel)

00H-7FH

Channel Detune ch: 00H-0FH 43H (Sets the Detune value for

each channel)

00H-7FH

Voice Reserve ch: 00H-0FH 45H 00H : Reserve off

7FH : on*

* When Volume, Expression is received for Reserve On, they will

be effective from the next Key On. Reserve Off is normal.

11. SYSTEM EXCLUSIVE MESSAGES (Others)

Data format: [F0H] -> [43H] -> [1nH] -> [27H] -> [30H] ->

[00H] -> [00H] -> [mmH] -> [llH] -> [ccH] ->

[F7H]

Master Tuning (XG and last message priority) simultaneously

changes the pitch of all channels.

F0H = Exclusive Status

43H = Yamaha ID

1nH = Transmission from n=CLP is always 0. 0-F is received.

27H = Model ID of TG100

30H = Sub ID

00H =

mmH = Master Tune MSB

llH = Master Tune LSB

ccH = don’t care (under 7FH)

F7H = End of Exclusive

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha CLP-880 Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha CLP-880

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info