Bedienungsanleitung Yamaha CLP-970M (Seite 24 von 36) (Französisch)

593334

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

CLP-970

MIDI Data Format

1.2.14 Attack Time

This message adjusts the EG attack time that was speciﬁed by the sound data.

Control# Parameter Data Range

73 Attack Time 0...64...127 (-64...0...+63)

Since this a relative change parameter, it speciﬁes an increase or decrease relative to 64.

Increasing this value will make the attack more gradual, and decreasing this value will

make the attack sharper.

1.2.15 Brightness

This message adjusts the cutoff frequency of the low pass ﬁlter speciﬁed by the sound data.

Control# Parameter Data Range

74 Brightness 0...64...127 (-64...0...+63)

Since this is a relative change parameter, it speciﬁes an increase or decrease relative to 64.

Lower values will produce a more mellow sound.

For some sounds, the effective range may be less than the possible range of settings.

1.2.16 Portamento Control

This message speciﬁes the portamento source key number (the key number at which porta-

mento will begin).

Data of 0...127 speciﬁes the portamento source key.

When Portamento Control is received, the currently-sounding pitch will change at a Porta-

mento Time of 0 to the key of the next-received note-on of the same channel.

Control# Parameter Data Range

84 Portamento Control 0...127 (C-2...G8)

This is received even if Rcv PORTAMENTO = OFF.

1.2.17 Effect1 Depth(Reverb Send Level)

This message speciﬁes the send level for the reverb effect.

Control# Parameter Data Range

91 Effect1 Depth 0...127

Increasing this value will produce a richer reverb. The effect of the value will depend on

the state of the reverb effect.

1.2.18 Effect3 Depth(Chorus Send Level)

This message speciﬁes the send level for the chorus effect.

Control# Parameter Data Range

93 Effect3 Depth 0...127

Raising this value will increase the modulation or spaciousness. The effect of the value

will depend on the state of the chorus effect.

1.2.19 Effect4 Depth (Variation Effect Send Level)

This message speciﬁes the send level for the variation effect.

Control# Parameter Data Range

94 Effect4 Depth 0...127

However, this is not received if the Variation Effect parameter Variation Connection = 0

(Insertion).

1.2.20 Data Increment/Decrement (for RPN)

This message increases or decreases the parameter value speciﬁed for RPN (see 1.2.22), by

increments of 1.

Control# Parameter Data Range

96 RPN Increment --

97 RPN Decrement --

The data byte is ignored.

1.2.21 NRPN (Non-registered parameter number)

This message is used to specify a sound parameter (such as vibrato, ﬁlter, EG, drum setup

etc.) as an offset value.

Use NRPN MSB and NRPN LSB to specify the parameter that you wish to modify, and

then use Data Entry (see 1.2.4) to set the value for the speciﬁed parameter.

Control# Parameter Data Range

98 NRPN LSB 0...127

99 NRPN MSB 0...127

If the Multi Part parameter Rcv NRPN = OFF, that part will not receive NRPN.

The following NRPN messages can be received.

MSB 20-31 (for drums) is received when Multi Part parameter PART MODE = DRUMS1, 2.

*1 Refer to 1.2.4

*2 ‘--’ indicates that the setting value is ignored.

1.2.22 RPN (Registered parameter number)

This message is used to specify part parameters such as Pitch Bend Sensitivity or Tuning

etc. as an offset value.

Use RPN MSB and RPN LSB to specify the parameter that you wish to modify, and then

use Data Entry (see 1.2.4) to set the value of the speciﬁed parameter.

Control# Parameter Data Range

100 RPN LSB 0...127

101 RPN MSB 0...127

If the Multi Part parameter Rcv RPN = OFF, that part will not receive this message.

NRPN

MSB LSB

Data Entry *1

MSB LSB

Parameter name and value range

01 08 mm -- *2 Vibrato rate