Bedienungsanleitung Yamaha CLP230 (Seite 52 von 90) (Englisch)

27512

Zoom out

Zoom in

Vorherige Seite

1/90

Nächste Seite

Detailed Settings – [FUNCTION]

CLP-240/230 Owner’s Manual

ENGLISH

You can change the volume of the metronome

sound.

Use this function to adjust the metronome vol-

ume.

1. Engage the Function mode and select

(CLP-240)/ (CLP-230).

2. Use the [–/NO] and [+/YES] buttons to set the

metronome volume as required.

Setting range: 1 – 20

Normal setting: 10

This function sets the volume at which a “can-

celed” part is played during song playback.

Adjust the part volume to a comfortable level

and use the “canceled” part as a guide with

which to play along.

1. Engage the Function mode and select

(CLP-240)/ (CLP-230).

2. Use the [–/NO] and [+/YES] buttons to set the

volume as required.

Setting range: 0 – 20

Normal setting: 5

You can make detailed adjustments to MIDI

settings.

For more information about MIDI, see the

“About MIDI” section (page 57).

1. Engage the Function mode and select

(CLP-240)/ (CLP-230).

2. Press the [+/YES] button to engage the MIDI

function’s sub-mode, then use the [TEMPO/

FUNCTION# ▼, ▲] buttons to select the

desired sub-mode.

Press the [–/NO] or [+/YES] button to set a

selected parameter.

Sub-mode

F8.1:

(CLP-240)/F7.1: (CLP-230)

MIDI Transmit Channel Selection

In any MIDI control setup, the MIDI channels of the

transmitting and receiving equipment must be matched

for proper data transfer.

This parameter enables you to specify the channel on

which the Clavinova transmits MIDI data.

Setting range: 1 – 16, OFF (not transmitted)

Normal setting: 1

F6. (CLP-240) / F5. (CLP-230)

Metronome Volume

NOTE

SHORTCUT:

You can jump directly to the metronome functions (CLP-

240)/ (CLP-230) by pressing the [TEMPO/FUNCTION#]

button while holding the METRONOME [ON/OFF] button.

To exit the Function mode, you still need to press the [TEMPO/

FUNCTION#] button so that the TEMPO indicator lights up.

F7. (CLP-240) / F6. (CLP-230)

Song Part Cancel Volume

NOTE

This function cannot be used for Demo songs.

F8. (CLP-240) / F7. (CLP-230)

MIDI Functions

All MIDI settings described below will affect the MIDI signal

in and out of the USB [TO HOST] connector.

NOTE

In Dual mode, Voice 1 data is transmitted on its speciﬁed chan-

nel. In Split mode (CLP-240), right voice data is transmitted on

its speciﬁed channel. In Dual mode, Voice 2 data is transmitted

on the next greater channel number relative to the speciﬁed

channel. In Split mode (CLP-240), left voice data is transmitted

on the next greater channel number relative to the speciﬁed

channel. In either mode, no data is transmitted if the transmit

channel is set to “OFF.”

NOTE

Song data is not transmitted via the MIDI connections. However,

channels 3-16 of DOC songs, Disklavier Piano Soft songs, and

non-protected External songs will be transmitted via the MIDI

connections depending on the Song Channel Selection setting

(page 51).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha CLP230 Seite 52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha CLP230

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info