Bedienungsanleitung Yamaha CLP230 (Seite 64 von 90) (Englisch)

27512

Zoom out

Zoom in

Vorherige Seite

1/90

Nächste Seite

Troubleshooting

CLP-240/230 Owner’s Manual

ENGLISH

Troubleshooting

Options

BC-100 Bench

A comfortable bench styled to match your Yamaha Clavinova.

HPE-160 Stereo Headphones

High-performance lightweight dynamic headphones with extra-soft ear pads.

UD-FD01 USB-FDD Unit (CLP-240)

Floppy disk drive for connecting to the instrument and saving/loading data.

Problem Possible Cause and Solution

The Clavinova does not turn on. The Clavinova has not been plugged in properly. Securely insert the female plug into

the socket on the Clavinova, and the male plug into a proper AC outlet (page 11).

A click or pop is heard when the power is

turned on or off.

This is normal when electrical current is being applied to the instrument.

Noise is heard from the speakers or head-

phones.

The noise may be due to interference caused by the use of a mobile phone in close

proximity to the Clavinova. Turn off the mobile phone, or use it further away from the

Clavinova.

The overall volume is low, or no sound is

heard.

• The Master Volume is set too low; set it to an appropriate level using the [MASTER

VOLUME] control.

• Make sure a pair of headphones is not connected to the headphones jack (when the

SPEAKER switch is set to the “NORMAL” position). If the SPEAKER switch is set to

the “OFF” position, set it to “NORMAL” or “ON” (page 12).

• Make sure that Local Control (page 53) is ON.

The speakers do not switch off when a pair of

headphones is connected.

The SPEAKER switch may be switched “ON.” Set the SPEAKER switch to the “NOR-

MAL” position (page 12).

The damper pedal has no effect, or the sound

continuously sustains even when the damper

pedal is not pressed.

The pedal cable/plug may not be properly connected. Make sure to securely insert the

pedal plug into the proper jack (page 67).

(CLP-240)

Even though a USB storage device is con-

nected, the SONG SELECT “USB” indicator

does not turn on when pressing the [SONG

SELECT] button.

The USB storage device may not be recognized by the instrument, depending on the

device itself or the timing of the recognition.

1. Check the [SELECT] switch.

Switching to “A” selects the terminal on the left of the panel, while switching to “B”

selects the terminal panel at the bottom.

2. Check that the device is not damaged.

Check that the FILE “LOAD” indicator ﬂashes after connecting the USB storage

device. If the indicator does not ﬂash, the device may be damaged.

3. Check that the compatibility of the device has been conﬁrmed by Yamaha (page 58).

4. Select SONG SELECT “USB” again.

It may take a while for the instrument to recognize the USB storage device. Press

the [SONG SELECT] button again to turn the “USB” indicator on.

(CLP-240)

The USB storage device has hung up

(stopped).

• The USB storage device is not compatible with the instrument. Only use the devices

whose compatibility has been conﬁrmed by Yamaha (page 58).

• Disconnect the device and connect it to the instrument again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha CLP230 Seite 64

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha CLP230

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info