Bedienungsanleitung Yamaha CP5 (Seite 53 von 68) (Englisch)

516892

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Troubleshooting

CP5/CP50 Owner’s Manual 53

Appendix

Troubleshooting

If you should experience difficulties with your CP5 or CP50, such as an inability to produce any sound or the output

becoming distorted, work through the following checklists in order to rectify the situation. Alternatively, the Factory Set

function (page 51) can also be used to resolve problems after first creating a complete backup of the stage piano’s data

on an external device (page 52). If any specific problem should persist, however, please contact a Yamaha

representative or authorized distributor (see the back of this booklet).

The stage piano produces no sound.

Ensure that a stereo system, an amplifier and speakers, or headphones have been connected to

your CP5 or CP50.

This stage piano does not come with built-in speakers. In order to hear the sounds that it produces, therefore, you will

need to connect headphones or an external amplifier and speakers (page 15).

Ensure that the stage piano and the connected audio equipment are turned on.

Ensure that the master volume on your CP5 or CP50 and on the connected audio equipment are not

set to an excessively low level.

If a foot controller has been connected to the stage piano, try using it to increase the volume.

Ensure that MIDI volume or expression has not been set excessively low by an external MIDI

controller.

Ensure that your CP5 or CP50 has been correctly connected to the external audio equipment (such

as an amplifier and speakers).

Ensure that local control has not been turned off.

If local control is turned off and your CP5 or CP50 is not being used together with a computer or another device

returning MIDI messages, it will not be possible to produce any sound from the internal tone generator by playing the

keyboard.

Ensure that no part volumes have been set to an excessively low level.

Ensure that Part buttons are not turned off.

If a Part button is turned off (i.e., if the lamp to its top-left is not lit), the part in question will not produce any sound. To

remedy this situation, press the Part button and confirm that its lamp lights up.

Ensure that the output volumes for the Pre-Amplifier blocks and the Power-Amplifier / Compressor

blocks (CP5 only) are not fully turned down.

Each Pre-Amplifier block (voices from E.PIANO category only):

Each Power-Amplifier / Compressor block (CP5 only)

Press the [UTILITY] button  Jump to Page 5 by pressing the [5] button  Turn Knob 3 to set LocalSw to “on”  Press the [STORE]

button to store this setting (page 48).

Press and hold the [PRE-AMP] button (for at least one second)  Jump to Page 4 by pressing the [4] button  Turn Knob 2 to set the

Volume parameter to an appropriate level. (See the Reference Manual pdf document for more details.)

Press and hold the [PWR-AMP] button (for at least one second)  Set the volume to an appropriate level. (See the Reference

Manual pdf document for more details.)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha CP5 Seite 53

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha CP5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info