Bedienungsanleitung Yamaha CS6R (Seite 126 von 196) (Englisch)

48734

126

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

126

Performance Mode

CTL Assign1(Controller Assign 1)

Use Knobs [C], [1] and [2] to assign Control Numbers

to the Breath Controller, Knob [1] and Knob [2],

respectively. The selected function is shown on the left

of the display.

■ BC (Breath Controller)

Set Control Change Number assigned to the Breath

Controller. The Breath Controller is connected to

the BREATH jack (Page 18).

❏ Settings: Details are given in the separate Control List.

■ Knob1/2

Set Control Change Numbers assigned to Knobs [1]

and [2] on the front panel.

CTL Assign2 (Controller Assign 2)

Use Knobs [C] and [1] to assign Control Change

Numbers to the Foot Controller and Ribbon Controller,

respectively. The selected function is shown on the left

of the display. Use Knob [2] to select the Ribbon

Controller Mode.

■ FC (Foot Controller)

Assign a Controller Change Number to the Foot

Controller. The Foot Controller is connected to the

FOOT CONTROLLER jack on the rear panel (Page 18).

❏ Settings: Details are given in the separate Control List.

■ RB (Ribbon Controller)

Assign a Control Change Number to the Ribbon

Controller on the front panel. The Ribbon

Controller’s behavior depends on the Mode

parameter setting.

❏ Settings: Details are given in the separate Control List.

SHIFT PAGE

PART

ELEMENT

DATAA B C 1 2

CTLíAssign2) FC RB----Mode

Common [FootCtrl] 04 PB reset

Control Change Name

Control Change Number

Mode

SHIFT PAGE

PART

ELEMENT

DATAA B C 1 2

CTLíAssign1) BC Knob1 Knob2

Common [FootCtrl] 02 16 17

Control Change Name Control Change Numbers

■ Mode

Set the behavior of the Ribbon Controller. If you

select “hold,” the parameter controlled by the

Ribbon Controller will hold its value even after you

release it. If you select “reset,” the value returns to

its default setting at the center of the Ribbon

Controller strip.

❏ Settings: hold, reset

Common EQ (Equalizer)

You can assign any of five different Equalizer bands to

the entire Performance. The following five screens are

available.

EQ Low

EQ LowMid (Low-Middle Range)

EQ Mid (Middle Range)

EQ HighMid (High-Middle Range)

EQ High

EQ Low

This Equalizer covers low frequencies. You can adjust

the signal level at the specified frequency. You can also

select different Equalizer types (Shapes).

■ Shape

Select either a Shelving or Peaking equalizer. The

Peaking type attenuates/boosts the signal at the

specified Frequency setting, whereas the Shelving

type attenuates/boosts the signal at frequencies

above or below the specified Frequency setting.

❏ Settings: shelv (Shelving), peak (Peaking)

shelv (Shelving)

Frequency

EQ Low

Freq1

EQ Low

Freq2

MEQíLow) Shape Gain Freq Q

Common peak +12dB 50Hz 12.0

Q (Frequency Characteristic)

Gain

Freq (Frequency)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha CS6R Seite 126

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha CS6R

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info