Bedienungsanleitung Yamaha CS6R (Seite 152 von 196) (Englisch)

48734

152

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

152

Phrase Clip Mode

■ KeyOn

Select the Key On method. There are two methods:

normal and hold.

❏ Settings:

normal:

Pressing a Clip Key starts playback of a Clip. Playback will

continue until the key is released.

hold:

Pressing a Clip Key triggers playback of a Clip. Playback

will continue after the key is released, until another Clip

Key is pressed.

■ Assign

Set Key Assign to “single” to prevent the doubled

playback of the same received notes. Select “multi”

to consecutively assign each instance of the same

received note to a separate channel.

❏ Settings: single, multi

■ AltGrp (Alternate Group)

You can prevent different Phrase Clips from playing

back simultaneously by assigning them to the same

Alternate Group. This is useful, for example, when

you want to prevent drum loops from overlapping

during playback. Up to 127 Alternate Groups can be

defined. You can also select “off” here if you wish to

allow the simultaneous playback of all Phrase Clips.

❏ Settings: off, 1 ~ 127

Clip Key Pitch

Set the pitch of each Clip Key. The tunings and Pitch

EG parameters can be set for each Clip Key.

PCH Tune (Pitch Tune)

■ Coarse

Adjust the pitch of each Phrase Clip in semitones.

❏ Settings: -48 ~ 0 ~ +48

■ Fine

Fine-tune the pitch of each Phrase Clip.

❏ Settings: -64 ~ 0 ~ +63

■ VelSens (Velocity Sensitivity)

Set the velocity sensitivity of the pitch. Positive settings

will cause the pitch to become raised when you play the

keyboard harder (for a large Velocity value). Negative

settings will cause it to become lowered.

❏ Settings: -64 ~ 0 ~ +63

PCHíTune) Coarse Fine VelSens

Key=C 3 + 0 + 0 +63

Clip Key Filter

You can apply filter settings to Clip Keys. A Low Pass

Filter and High Pass Filter can be applied per Phrase

Clip to change its tonal characteristics.

FLT Cutoff (Filter Cutoff)

■ LPF (Low Pass Filter)

Set the Cutoff frequency of the Low Pass Filter.

Only frequencies below this point are passed. You

can then use the Reso (Resonance) parameter to add

further character to the sound.

❏ Settings: 0 ~ 255

Details about the Low Pass Filter are given on Page 93.

■ VelSens (Velocity Sensitivity)

Set the velocity sensitivity of the Low Pass Filter

Cutoff frequency. Positive settings will cause the

cutoff frequency to become higher when you play the

keyboard harder (for a large Velocity value),

resulting in a drastic change in tones. Negative

settings will cause it to become lower.

❏ Settings: -64 ~ 0 ~ +63

■ Reso (Resonance)

Set the amount of Resonance (harmonic emphasis)

applied to the signal at the Cutoff frequency. This can

be used in combination with the Cutoff frequency of the

Low Pass Filter to add further character to the sound.

❏ Settings: 0 ~ 31

Details about Resonance are given on Page 40.

■ HPF (High Pass Filter)

Set the Cutoff frequency of the High Pass Filter.

Only frequencies above this point are passed.

❏ Settings: 0 ~ 255

Details about the High Pass Filter are given on Page 94.

Clip Key Amplitude

You can set amplitude (output level) parameters for each

Phrase Clip. The following two screens are available.

AMP AEG (Amplitude Envelope Generator)

AMP VelSens (Amplitude Velocity Sensitivity)

FLTíCutoff) LPF VelSens Reso HPF

Key=C 3 255 +63 31 0

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha CS6R Seite 152

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha CS6R

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info