Bedienungsanleitung Yamaha CVP-107 (Seite 148 von 235) (Englisch)

593661

148

Zoom out

Zoom in

Vorherige Seite

1/235

Nächste Seite

148

CVP-109/107/105/700

➔ The track selector is highlighted, and the event data for the se-

lected track is displayed.

N Select an event to edit................................................................................

V Select a track to edit..................................................................................

Track selector

Settings: SYSTEM, TRACK 1 — 16

Press the uppermost left LCD button once to highlight the track

selector, then use the data dial or the [–] and [+] buttons to select the

track you want to edit.

• System Exclusive events (see page

146) are loaded into Track 1.

• Meta events (see page 146) are

loaded into the SYSTEM track.

B Select a location................................................................................................

Measure selector

• The measure selector can be set to

INITIAL (in which case the beat and

clock values are not displayed), or to

any value between 1 and 9999.

• The INITIAL setting is used to set

events (such as the voice selection or

volume events) that occur before the

song begins. (Actual song playback

begins with the first beat of measure 1.)

Press uppermost left LCD button again to highlight the right side of

the location indicator, then use the data dial or the [–] and [+] buttons to

select the measure you want to edit.

➔ The selected measure is highlighted, and the beat and clock val-

ues are displayed.

Beat and clock

• The beat value can be set to any value

between 1 and n, where n is the

number of beats in the selected meas-

ure.

• Each quarter note is divided into 480

smaller units (numbered 0 to 479), which

can be used to set the timing of events

that don’t occur precisely on the beat. If

each beat is a quarter note, for example,

the location clock values of two eighth

notes might be set to 0 and 240,

whereas those of four sixteenth notes

would be set to 0, 120, 240, and 360.

➾ Repeat this step to set the beat and clock values. The track selec-

tor, measure selector, beat, and clock values are highlighted in

turn with each press of the uppermost left LCD button.

➔ The first four events that occur at or after the specified location are

displayed. The first of these events is highlighted.

Scrolling the Event List

• To display other events before or

after the selected timing, hold down

one of those four buttons, then use

the data dial or the [–] and [+] buttons

to scroll the event list up or down.

• You can also press the TIMING LCD

button to select the double-pointed

arrow ( ) symbol in the leftmost

column of event data, then use the

data dial or the [–] and [+] buttons to

scroll the event list.

Use one of the bottom four buttons to the left of the LCD to select

the corresponding event in the display.

➔ The selected event is highlighted, and the timing of that event is

shown as the location in the first line of the display.

Measure Beat Clock

Step Edit

146

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha CVP-107 Seite 148

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha CVP-107

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info