Bedienungsanleitung Yamaha CVP-109 (Seite 18 von 68) (Spanisch)

593674

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

CVP-109/107/105/103/700

MIDI Data Format

MIDI-Datenformat

Format des données MIDI

Formato de datos MIDI

• HARMONIC CONTENT applies adjustment to the resonance value that

is set by the voice. This parameter specifies relative change with the

value of 64 producing 0 adjustment. As values get higher the sound

becomes increasingly eccentric. Note that for some voices the effective

parameter range is narrower than the legal parameter range.

• RELEASE TIME applies adjustment to the envelope release time set by

the voice. This parameter specifies relative change with the value of 64

producing 0 adjustment.

• ATTACK TIME applies adjustment to the envelope attack time set by the

voice. This parameter specifies relative change with the value of 64

producing 0 adjustment.

• BRIGHTNESS applies adjustment to the cut-off frequency set by the

voice. This parameter specifies relative change with the value of 64

producing 0 adjustment. Lower voices produce a softer sound. For some

voices the effective parameter range is narrower than the legal

parameter range.

(3-2) CHANNEL MODE MESSAGES

STATUS 1011nnnn(BnH) n = 0 - 15 VOICE CHANNEL NUMBER

CONTROL NUMBER 0ccccccc c = CONTROL NUMBER

CONTROL VALUE 0vvvvvvv v = DATA VALUE

(3-2-1) ALL SOUND OFF (Receive only)

(CONTROL NUMBER = 78H , DATA VALUE = 0)

Switches off all sound from the channel. Reset Note On and Hold On conditions established

by Channel Messages.

(3-2-2) RESET ALL CONTROLLERS (Receive only)

(CONTROL NUMBER = 79H , DATA VALUE = 0)

Resets controllers as follows.

PITCH BEND CHANGE 0 (Center)

AFTER TOUCH 0 (min.)

MODULATION 0 (min.)

EXPRESSION 127 (max.)

SUSTAIN 0 (off)

SOSTENUTO 0 (off)

SOFT PEDAL 0 (off)

NRPN Sets number to null. (Internal data remains unchanged)

RPN Sets number to null. (Internal data remains unchanged)

PORTAMENT CONTROL Resets portamento source note number

PORTAMENTO 0 (off)

(3-2-3) ALL NOTES OFF (Receive only)

(CONTROL NUMBER = 7BH , DATA VALUE = 0)

Switches off all of the channel’s “on” notes. However, any notes being held by SUSTAIN or

SOSTENUTO continue to sound until SUSTAIN/SOSTENUTO goes off.

(3-2-4)

OMNI OFF (Receive only) (CONTROL NUMBER = 7CH , DATA VALUE = 0)

Same processing as for All Notes Off.

(3-2-5) OMNI ON (Receive only)

(CONTROL NUMBER = 7DH , DATA VALUE = 0)

Same processing as for All Notes Off. Omni On is not executed.

(3-2-6) MONO (Receive only)

(CONTROL NUMBER = 7EH , DATA VALUE = 0)

Same processing as for All Notes Off. If the 3rd byte is in a range of 0-16 the corresponding

channel will be changed to Mode 4 (m=1).

(3-2-7) POLY (Receive only) (CONTROL NUMBER = 7FH , DATA VALUE = 0)

Same processing as for All Sounds Off and the corresponding channel will be changed to

Mode 3.

(3-3) REGISTERED PARAMETER NUMBER(RPN)

STATUS 1011nnnn(BnH) n = 0 - 15 VOICE CHANNEL NUMBER

RPN LSB 01100100(64H)

RPN LSB NUMBER 0ppppppp p = RPN LSB (refer to the list below)

RPN MSB 01100101(65H)

RPN MSB NUMBER 0qqqqqqq q = RPN MSB (refer to the list below)

DATA ENTRY MSB 00000110(06H)

DATA VALUE 0mmmmmmm m = Data Value

DATA ENTRY LSB 00100110(26H)

DATA VALUE 0lllllll l = Data Value

First appoints the parameter for RPN MSB/LSB, then sets the parameter value for data entry

MSB/LSB.

RPN D.ENTRY

LSB MSB MSB LSB PARAMETER NAME DATA RANGE

00H 00H mmH —

PITCH BEND SENSITIVITY

00H-18H (0 - 24 semitones)

01H 00H mmH llH FINE TUNE

{mmH,llH} = {00H,00H}-{40H,00H}-{7FH,7FH}

(-8192*100/8192) - 0 - (+8192*100/8192)

02H 00H mmH — COARSE TUNE

28H - 40H - 58H (-24 - 0 - +24 semitones)

7FH 7FH — — NULL Clears the current RPN number setting.

Does not change the internal parameter settings.

(3-4) NON-REGISTERED PARAMETER NUMBER(NRPN) (Receive only)

STATUS 1011nnnn(BnH) n = 0 - 15 VOICE CHANNEL NUMBER

NRPN LSB 01100010(62H)

NRPN LSB NUMBER 0ppppppp p = NRPN LSB (refer to the list below)

NRPN MSB 01100011(63H)

NRPN MSB NUMBER 0qqqqqqq q = NRPN MSB (refer to the list below)

DATA ENTRY MSB 00000110(06H)

DATA VALUE 0mmmmmmm m = Data Value

First appoints the parameter for NRPN MSB/LSB, then sets the parameter value for data entry

MSB/LSB.

NRPN D.ENTRY

MSB LSB MSB LSB PARAMETER NAMEDATA RANGE

01H 08H mmH — VIBRATO RATE

00H - 40H - 7FH (-64 - 0 - +63)

01H 09H mmH — VIBRATO DEPTH

00H - 40H - 7FH (-64 - 0 - +63)

01H 0AH mmH — VIBRATO DELAY

00H - 40H - 7FH (-64 - 0 - +63)

01H 20H mmH —

FILTER CUTOFF FREQUENCY

00H - 40H - 7FH (-64 - 0 - +63)

01H 21H mmH — FILTER RESONANCE

00H - 40H - 7FH (-64 - 0 - +63)

01H 30H mmH —

EQ BASS (CVP-109/107/700)

00H - 40H - 7FH (-64 - 0 - +63)

01H 31H mmH —

EQ TREBLE

(CVP-109/107/700) 00H - 40H - 7FH (-64 - 0 - +63)

01H 34H mmH —

EQ BASS FREQ.

(CVP-109/107/700)

00H - 40H - 7FH (-64 - 0 - +63)

01H 35H mmH —

EQ TREBLE FREQ.

(CVP-109/107/700)

00H - 40H - 7FH (-64 - 0 - +63)

01H 63H mmH — EG ATTACK TIME

00H - 40H - 7FH (-64 - 0 - +63)

01H 64H mmH — EG DECAY TIME

00H - 40H - 7FH (-64 - 0 - +63)

01H 66H mmH — EG RELEASE

00H - 40H - 7FH (-64 - 0 - +63)

14H rrH mmH —

DRUM FILTER CUTOFF FREQ. 00H - 40H - 7FH (-64 - 0 - +63)

15H rrH mmH —

DRUM FILTER RESONANCE

00H - 40H - 7FH (-64 - 0 - +63)

16H rrH mmH — DRUM AEG ATTACK RATE

00H - 40H - 7FH (-64 - 0 - +63)

17H rrH mmH — DRUM AEG DECAY RATE

00H - 40H - 7FH (-64 - 0 - +63)

18H rrH mmH — DRUM PITCH COARSE

00H - 40H - 7FH (-64 - 0 - +63)

19H rrH mmH — DRUM PITCH FINE

00H - 40H - 7FH (-64 - 0 - +63)

1AH rrH mmH — DRUM LEVEL

00H - 7FH (0 - max.)

1CH rrH mmH — DRUM PANPOT

00H ,01H - 40H - 7FH

(random,left - center - right)

1DH rrH mmH —

DRUM REVERB SEND LEVEL

00H - 7FH (0 - max.)

1EH rrH mmH —

DRUM CHORUS SEND LEVEL

00H - 7FH (0 - max.)

1FH rrH mmH —

DRUM VARIATION SEND LEVEL 00H - 7FH (0 - max.)

The MSB 14H-1FH (for drums) message is received when multi-part parameters PART

MODE = DRUMS1...2.

rrH : drum instrument note number

(3-5) SYSTEM REALTIME MESSAGES

(3-5-1) MIDI CLOCK

STATUS 11111000 (F8H)

Transmission: 96 clocks per measure are transmitted.

Reception: If the instrument’s clock is set to external, after FAH is received from the external

device the instrument’s clock will sync with the 96 beats per measure received from the external

device.

Decides whether the internal clock, or Timing Clocks received via the MIDI IN will be used.

(3-5-2) START

STATUS 11111010 (FAH)

Transmission: Transmitted when instrument’s Rhythm or Song playback is started.

Reception: Depending upon the condition, Rhythm, Song Playback, or Song Rec will start.

(3-5-3) STOP

STATUS 11111100 (FCH)

Transmission: Transmitted when instrument’s Rhythm or Song playback is stopped.

Reception: Depending upon the condition, Rhythm, Song Playback, or Song Rec will stop.

(3-5-4) ACTIVE SENSING

STATUS 11111110 (FEH)

Transmission: Transmitted approximately once every 200msec.

Reception: Sensing is started once this Code is received. If Status or Data is not received within

400ms, the MIDI Receive Buffer will be cleared, and all notes, including those being sustained,

will be cut OFF. Also, all control values will be reset to their factory defaults.

Yamaha CVP-109 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha CVP-109

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info