Bedienungsanleitung Yamaha CVP-201 (Seite 15 von 39) (Französisch)

593682

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

CVP-201

• Portamento time is fixed to 0 when the PORTAMENTO CONTROL is

used.

• HARMONIC CONTENT applies adjustment to the resonance value that

is set by the voice. This parameter specifies relative change with the

value of 64 producing 0 adjustment. As values get higher the sound

becomes increasingly eccentric. Note that for some voices the effective

parameter range is narrower than the legal parameter range.

• RELEASE TIME applies adjustment to the envelope release time set by

the voice. This parameter specifies relative change with the value of 64

producing 0 adjustment.

• ATTACK TIME applies adjustment to the envelope attack time set by the

voice. This parameter specifies relative change with the value of 64

producing 0 adjustment.

• BRIGHTNESS applies adjustment to the cut-off frequency set by the

voice. This parameter specifies relative change with the value of 64

producing 0 adjustment. Lower voices produce a softer sound. For some

voices the effective parameter range is narrower than the legal

parameter range.

(3-2) CHANNEL MODE MESSAGES

STATUS 1011nnnn(BnH) n = 0 - 15 VOICE CHANNEL NUMBER

CONTROL NUMBER 0ccccccc c = CONTROL NUMBER

CONTROL VALUE 0vvvvvvv v = DATA VALUE

(3-2-1) ALL SOUND OFF (Receive only)

(CONTROL NUMBER = 78H , DATA VALUE = 0)

Switches off all sound from the channel. Reset Note On and Hold On conditions established

by Channel Messages.

(3-2-2) RESET ALL CONTROLLERS (Receive only)

(CONTROL NUMBER = 79H , DATA VALUE = 0)

Resets controllers as follows.

PITCH BEND CHANGE 0 (Center)

AFTER TOUCH 0 (min.)

MODULATION 0 (min.)

EXPRESSION 127 (max.)

SUSTAIN 0 (off)

SOSTENUTO 0 (off)

SOFT PEDAL 0 (off)

NRPN Sets number to null. (Internal data remains unchanged)

RPN Sets number to null. (Internal data remains unchanged)

PORTAMENT CONTROL Resets portamento source note number

PORTAMENTO 0 (off)

(3-2-3) ALL NOTES OFF (Receive only)

(CONTROL NUMBER = 7BH , DATA VALUE = 0)

Switches off all of the channel’s “on” notes. However, any notes being held by SUSTAIN or

SOSTENUTO continue to sound until SUSTAIN/SOSTENUTO goes off.

(3-2-4)

OMNI OFF (Receive only) (CONTROL NUMBER = 7CH , DATA VALUE = 0)

Same processing as for All Notes Off.

(3-2-5) OMNI ON (Receive only)

(CONTROL NUMBER = 7DH , DATA VALUE = 0)

Same processing as for All Notes Off. Omni On is not executed.

(3-2-6) MONO (Receive only)

(CONTROL NUMBER = 7EH , DATA VALUE = 0)

Same processing as for All Notes Off. If the 3rd byte is in a range of 0-16 the corresponding

channel will be changed to Mode 4 (m=1).

(3-2-7) POLY (Receive only) (CONTROL NUMBER = 7FH , DATA VALUE = 0)

Same processing as for All Sounds Off and the corresponding channel will be changed to

Mode 3.

(3-3) REGISTERED PARAMETER NUMBER(RPN)

STATUS 1011nnnn(BnH) n = 0 - 15 VOICE CHANNEL NUMBER

RPN LSB 01100100(64H)

RPN LSB NUMBER 0ppppppp p = RPN LSB (refer to the list below)

RPN MSB 01100101(65H)

RPN MSB NUMBER 0qqqqqqq q = RPN MSB (refer to the list below)

DATA ENTRY MSB 00000110(06H)

DATA VALUE 0mmmmmmm m = Data Value

DATA ENTRY LSB 00100110(26H)

DATA VALUE 0lllllll l = Data Value

First appoints the parameter for RPN MSB/LSB, then sets the parameter value for data entry

MSB/LSB.

RPN D.ENTRY

LSB MSB MSB LSB PARAMETER NAME DATA RANGE

00H 00H mmH —

PITCH BEND SENSITIVITY

00H-18H (0 - 24 semitones)

01H 00H mmH llH FINE TUNE

{mmH,llH} = {00H,00H}-{40H,00H}-{7FH,7FH}

(-8192*100/8192) - 0 - (+8192*100/8192)

02H 00H mmH — COARSE TUNE

28H - 40H - 58H (-24 - 0 - +24 semitones)

7FH 7FH — — NULL Clears the current RPN number setting.

Does not change the internal parameter settings.

(3-4) NON-REGISTERED PARAMETER NUMBER(NRPN) (Receive only)

STATUS 1011nnnn(BnH) n = 0 - 15 VOICE CHANNEL NUMBER

NRPN LSB 01100010(62H)

NRPN LSB NUMBER 0ppppppp p = NRPN LSB (refer to the list below)

NRPN MSB 01100011(63H)

NRPN MSB NUMBER 0qqqqqqq q = NRPN MSB (refer to the list below)

DATA ENTRY MSB 00000110(06H)

DATA VALUE 0mmmmmmm m = Data Value

First appoints the parameter for NRPN MSB/LSB, then sets the parameter value for data entry

MSB/LSB.

NRPN D.ENTRY

MSB LSB MSB LSB PARAMETER NAMEDATA RANGE

01H 08H mmH — VIBRATO RATE