Bedienungsanleitung Yamaha CVP-405 (Seite 201 von 226) (Englisch)

464219

201

Zoom out

Zoom in

Vorherige Seite

1/226

Nächste Seite

CVP-405/403/401 Owner’s Manual

201

Appendix

Troubleshooting

The instrument does not turn on.

• Securely insert the female plug into the socket on the

instrument, and the male plug into a proper AC outlet.

A click or pop is heard when the power is turned on

or off.

• Electrical current is being applied to the instrument. This

is normal.

Noise is heard from the instrument’s speakers.

• Noise may be heard if a mobile phone is used near the

instrument or if the phone is ringing. Turn off the mobile

phone, or use it further away from the instrument.

The letters in the display cannot be read, because the

display is too bright (or dark).

• Use the [LCD CONTRAST] knob to adjust for optimum

visibility.

• Adjust the brightness of the display (page 19).

The overall volume is too low, or, no sound is heard.

•The master volume may be set too low. Set it to an

appropriate level with the [MASTER VOLUME] dial.

•The volume of the individual parts may be set too low.

Raise the volume in the BALANCE display (page 40).

• Make sure the desired channel is set to ON (page 105).

• Headphones are connected, disabling the speaker out-

put. (This happens when the speaker setting is set to

“HEADPHONE SW”; page 17.) Unplug the headphones.

• Make sure the speaker setting is set to ON (page 17).

•The Fade-In and Fade-Out function is on, muting the

sound. To turn it off, press the pedal to which you

assigned the Fade In/Out function.

• Make sure the Local Control function is set to ON

(page 198).

Not all simultaneously played notes sound.

•You are probably exceeding the maximum polyphony

(page 213) of the instrument. When the maximum

polyphony is exceeded, the earliest played notes will

stop sounding, letting the latest played notes sound.

The keyboard volume is lower than the Song/Style

playback volume.

•The volume of the keyboard parts may be set too low.

Raise the volume in the BALANCE display (page 40).

Keys do not sound at the proper pitch.

• Make sure the Performance Assistant function is off on

the operation display (page 43).

Certain notes sound at the wrong pitch.

The Scale parameter has probably been set to some-

thing other than “Equal,” changing the tuning system of

the keyboard. Make sure “Equal” is selected as the

Scale in the Scale Tune display (page 83).

- There is a slight difference in sound quality among

different notes played on the keyboard.

- Some Voices have a looping sound.

- Some noise or vibrato is noticeable at higher

pitches, depending upon the voice.

•This is normal and is a result of the instrument’s sam-

pling system.

Some Voices will jump an octave in pitch when played

in the upper or lower registers.

•This is normal. Some voices have a pitch limit which,

when reached, causes this type of pitch shift.

The Main display does not appear even when turning

the power on.

•This may occur if a USB storage device has been

installed to the instrument. Installation of some USB stor-

age device may result a long interval between turning

the power on and appearance of the Main display. To

avoid this, turn the power on after disconnecting the

device.

The damper, sostenuto and soft functions do not

work for the relevant pedals.

•The pedal cord plug is not connected. Securely insert the

pedal cord plug into the proper jack (page 207).

• Each pedal has been assigned to a different function.

Make sure that each pedal is properly assigned to SUS-

TAIN, SOSTENUTO, and SOFT (page 187).

• Make sure the Registration Sequence function is set to

OFF (page 131).

Some characters of the ﬁle/folder name are garbled.

•The language settings have been changed. Set the appro-

priate language for the ﬁle/folder name (page 18).

An existing ﬁle is not shown.

•The ﬁle extension (.MID, etc.) may have been changed

or deleted. Manually rename the ﬁle, adding the appro-

priate extension, on a computer.

The data contained in the USB storage device is not

shown on the instrument itself.

• Data ﬁles with names of more than 50 characters cannot

be handled by the instrument. Rename the ﬁle, reducing

the number of characters to 50 or less.

Overall

Pedals

Files/Folders

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha CVP-405 Seite 201

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha CVP-405

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info