Bedienungsanleitung Yamaha CVP-405PM (Seite 207 von 226) (Englisch)

593776

207

Zoom out

Zoom in

Vorherige Seite

1/226

Nächste Seite

CVP-405/403/401 Owner’s Manual

207

Appendix

6 Installing E.

7 Connect the pedal cord.

8 Set the voltage selector and connect the power

cord.

Voltage Selector

Before connecting the AC power cord, check the setting of the volt-

age selector which is provided in some areas. To set the selector

for 110V, 127V, 220V or 240V main voltages, use a “minus” screw-

driver to rotate the selector dial so that the correct voltage for your

region appears next to the pointer on the panel. The voltage selec-

tor is set at 240V when the unit is initially shipped.

After the proper voltage has been selected, connect the AC

power cord to the AC INLET and an AC wall outlet. A plug adap-

tor may be also provided in some areas to match the pin conﬁg-

uration of the AC wall outlets in your area.

WARNING

An improper voltage setting can cause serious damage to

the instrument or result in improper operation.

9 Set the adjuster.

Rotate the adjuster until it

comes in ﬁrm contact with

the ﬂoor surface.

■ After completing the assembly, please check

the following.

1 Remove the plastic

cover from D.

2 Untie and straighten

out the bundled

cord attached to the

bottom of E.

3 Pass the pedal

cord between E

and D.

4 Make sure that E lays ﬂat, with no gap between

itself and the ﬂoor, then afﬁx the E using two

screws.

1 Insert the

pedal cord

plug into the

pedal connec-

tor.

Insert the plug

with the

arrow-printed side facing front

(toward the keyboard side).

If the plug will not go in easily,

do not force it. Double-check

the orientation of the plug,

then try again.

2 Align the pedal cord into

the groove on D, and install

the plastic cover onto the

groove. Be careful not to

insert the cover’s

attachment strip between

the groove wall and the leg.

Correct

Incorrect

240

127

110

220

(the bottom of the right side

as seen from the front)

• Are there any parts left over?

→ Review the assembly procedure and correct any

errors.

• Is the instrument clear of doors and other movable

ﬁxtures?

→ Move the instrument to an appropriate location.

• Does the instrument make a rattling noise when

you shake it?

→ Tighten all screws.

• Does the pedal box rattle or give way when you

step on the pedals?

→ Turn the adjuster so that it is set ﬁrmly against the

ﬂoor.

• Are the pedal and power cords inserted securely

into the sockets?

→ Check the connection.

• If the main unit creaks or is otherwise unsteady

when you play on the keyboard, refer to the assem-

bly diagrams and retighten all screws.

When moving the instrument after assembly, always

hold the bottom of the main unit.

CAUTION

Do not hold the key cover or top portion. Improper handling

can result in damage to the instrument or personal injury.

Top portion

Key cover

Do not hold here.

Hold here.

Do not

hold here.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha CVP-405PM Seite 207

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha CVP-405PM

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info