Bedienungsanleitung Yamaha CVP-501 (Seite 114 von 138) (Englisch)

593875

114

Zoom out

Zoom in

Vorherige Seite

1/138

Nächste Seite

114 CVP-509/505/503/501 Owner’s Manual

CVP-503: Keyboard Stand Assembly

CVP-503: Keyboard Stand

Assembly

CAUTION

• Assemble the stand on a hard and ﬂat ﬂoor with ample space.

• Be careful not to confuse parts, and be sure to install all parts in the correct direc-

tion. Please assemble in accordance with the sequence given below.

• Assembly should be carried out by at least two persons.

• Be sure to use the correct screw size, as indicated below. Use of incorrect screws

can cause damage.

• Be sure to tighten up all screws upon completing assembly of each unit.

• To disassemble, reverse the assembly sequence given below.

1 Open the package, take out marked “C” in the

illustration, take out the styrofoam pads, and

place the unit A on top of the pads.

Position the pads so that they will protect the headphone jack located

underneath the front left corner.

2 Attach C to D and E.

3 Attach B.

Depending on the model of digital piano you purchased, the surface

color of one side of the rear panel may be different from the other

side. In this case, position the rear panel so that the side of the surface

color similar to the side panel (left) and the side panel (right) faces

the player.

1 Place the lower side of B on each foot of D and E, then attach the

upper side to D and E.

2 Attach the top of B to D and E by ﬁnger-tightening the thin screws

(4 x 12mm).

3 While pushing the lower part of D and E from outside, secure the

bottom ends of B using two tapping screws (4 x 20mm).

4 Insert the other two tapping screws (4 x 20mm) into the other two

screw holes to secure B.

5 Securely tighten the screws on the top of B that were attached in

Step 3- 2).

4 Mount A.

Be sure to place your hands at least 10 cm from either end of A when

positioning it.

Have a Phillips-head (+) screwdriver of the appropriate size ready.

Main unit

Back panel

Side panel (left)

Side panel (right)

Assembly Parts

CAUTION

To prevent the key cover from accidentally opening during assembly, press

down on the key cover, making sure that the sheet (shown) remains in place.

Phones jacks Styrofoam pads

Pedal box

Bundled pedal cord inside

6 x 25 mm long screws x 4

6 x 16 mm short screws x 4

4 x 12 mm thin screws x 2

4 x 20 mm tapping screws x 4

Cord holders x 2

AC power cord

CAUTION

• Fingers can become pinched between A and C/D/E, be extra careful so

as not to drop A.

• Do not hold the keyboard in any position other than the position shown

in the illustration.

1 Untie and straighten out the bundled cord

attached to the bottom of the C. Don’t dis-

card the vinyl tie, you’ll need it later in

step 6.

2 Use the four 6 x 25 mm long screws to attach C. First attach

one side panel, then attach the other side panel.

At least

10 cm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha CVP-501 Seite 114

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha CVP-501

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info