Bedienungsanleitung Yamaha CVP-503 (Seite 120 von 138) (Englisch)

594735

120

Zoom out

Zoom in

Vorherige Seite

1/138

Nächste Seite

120 CVP-509/505/503/501 Owner’s Manual

Troubleshooting

Overall

A click or pop is heard when the power is turned on or off. Electrical current is being applied to the instrument. This is normal.

Noise is heard from the instrument’s speakers. Noise may be heard if a mobile phone is used near the instrument or

if the phone is ringing. Turn off the mobile phone, or use it further

away from the instrument.

In the LCD display, there are some black points (unlit) or white

points (always lit).

(CVP-509/505) These are the result of defective pixels and occasion-

ally occur in TFT-LCDs; they do not indicate a problem in operation.

There is a slight difference in sound quality among different notes

played on the keyboard.

This is normal and is a result of the instrument’s sampling system.

Some Voices have a looping sound.

Some noise or vibrato is noticeable at higher pitches, depending

upon the Voice.

The overall volume is too low, or, no sound is heard. The master volume may be set too low. Set it to an appropriate level

with the [MASTER VOLUME] dial.

All keyboard parts are set to off. Use the PART ON/OFF [RIGHT 1]/

[RIGHT 2]/[LEFT] button to turn it on.

The volume of the individual parts may be set too low. Raise the vol-

ume in the BALANCE display (page 58).

Make sure the desired channel is set to ON (pages 57, 64).

Headphones are connected, disabling the speaker output. Unplug the

headphones.

If the speaker is set to OFF. Make sure the speaker setting is set to

ON (page 110). For details, refer to the Reference Manual on the

website.

The sound is distorted or noisy. The volume may be turned up too high. Make sure all relevant volume

settings are appropriate.

This may be caused by certain effects or ﬁlter resonance settings.

Check the effect or ﬁlter settings and change them accordingly,

referring to the Reference Manual on the website.

Not all simultaneously played notes sound. You are probably exceeding the maximum polyphony (page 125) of

the instrument. When the maximum polyphony is exceeded, the earli-

est played notes will stop sounding, letting the latest played notes

sound.

The keyboard volume is lower than the Song/Style playback vol-

ume.

The volume of the keyboard parts may be set too low. Raise the vol-

ume in the BALANCE display (page 58).

The Main display does not appear even when turning the power on. This may occur if a USB storage device has been installed to the

instrument. Installation of some USB storage device may result a long

interval between turning the power on and appearance of the Main

display. To avoid this, turn the power on after disconnecting the

device.

Some characters of the ﬁle/folder name are garbled. The language settings have been changed. Set the appropriate lan-

guage for the ﬁle/folder name (page 17).

An existing ﬁle is not shown. The ﬁle extension (.MID, etc.) may have been changed or deleted.

Manually rename the ﬁle, adding the appropriate extension, on a

computer.

Data ﬁles with names of more than 50 characters cannot be handled

by the instrument. Rename the ﬁle, reducing the number of charac-

ters to 50 or less.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha CVP-503 Seite 120

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha CVP-503

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info