Bedienungsanleitung Yamaha CVP-69 (Seite 130 von 163) (Englisch)

599136

130

Zoom out

Zoom in

Vorherige Seite

1/163

Nächste Seite

127

2.1.5 Other Parameter Changes

2.1.5.1 Master Tuning

11110000 F0 Exclusive status

01000011 43 YAMAHA ID

0001nnnn 1n When n is received n=0~F, whichever is received.

When n is transmitted n always=0.

00100111 27 Model ID

00000001 30 Sub ID

00000000 00

mmmmmmm

mm Master Tune MSB

0lllllll ll Master Tune LSB

0ccccccc cc

11110111 F7 End of Exclusive

Changes tuning of all channels.

2.1.5.2 Channel Detune

11110000 F0 Exclusive status

01000011 43 YAMAHA ID

0001nnnn 73 Clavinova ID

00111001 39 CVP-79A/69/69A/59S ID

00010001 11 Sub ID

0000nnnn 0n n = MIDI Channel

01000011 43 Dual Detune

0vvvvvvv vv Value vv: $00 - $40 - $7F (-64 - 0 - +63)

11110111 F7 End of Exclusive

The Channel Detune message only affects the specified channel.

2.1.5.3 Volume and Expression Realtime Control Off

11110000 F0 Exclusive status

01000011 43 YAMAHA ID

0001nnnn 73 Clavinova ID

00111001 39 CVP-79A/69/69A/59S ID

00010001 11 Sub ID

0000nnnn 0n n = MIDI Channel

01000101 45 Volume and Expression Realtime Control Off

0vvvvvvv vv Value vv: $00:Off $7F:On

11110111 F7 End of Exclusive

When “On” is received subsequent volume and expression changes are only

valid during key on. Normal operation resumes when “Off” is received.

2.2 Bulk Dump

The CVP 79A/69/69A/59S models support the following parameters.

[XG NATIVE ]

1) XG System Data

2) Multi Effect1 Data

3) Drums Setup Data

2.2.1 XG Native Bulk Data

11110000 F0 Exclusive status

01000011 43 YAMAHA ID

0000nnnn 0n When n is received n=0~F, whichever is received.

When n is transmitted n always=0.

01001100 4C Model ID of XG

0bbbbbbb bbbbbbb ByteCount

0aaaaaaa aaaaaaa Address High

0aaaaaaa aaaaaaa Address Mid

0aaaaaaa aaaaaaa Address Low

00000000 00 Data

0ccccccc ccccccc Check sum

11110111 F7 End of Exclusive

For information about “Address” and “Byte Count” fields, refer to attached

tables.

In the attached tables “TOTAL SIZE” partitions a data series into single bulk

dumps. The “address” is the first byte of the bulk data.

The checksum value is set such that the sum of Byte Count, Address, Data, and

Checksum has value zero in its seven least significant bits.

If too much bulk data is received at a time there is a chance of error. The total

data for a bulk dump should not exceed 512 bytes, it is recommended that data

be kept under 512 bytes with an interval time of 120msec or more between 512

byte bulk.

2.2.1.1 XG System Data bulk dump

See Tables 1-1, 1-2.

2.2.1.2 Multi Effect1 Data bulk dump

See Tables 1-1, 1-3.

2.2.1.3 Drums Setup Data bulk dump

See Tables 1-1, 1-5.

2.3 Parameter Request

The CVP 79A/69/69A/59S models support the following request for

parameters covered by Parameter Change specifications.

11110000 F0 Exclusive status

01000011 43 YAMAHA ID

0011nnnn 3n When n is received n=0~F, whichever is received.

When n is transmitted n always=0.

01001100 4C Model ID of XG

0aaaaaaa aaaaaaa Address High

0aaaaaaa aaaaaaa Address Mid

0aaaaaaa aaaaaaa Address Low

11110111 F7 End of Exclusive

If the parameter’s data size is 2 or 4. The Parameter Request address for that

parameter is the first byte of the bulk.

2.4 Dump Request

The CVP 79A/69/69A/59S models support the following request for data

covered by bulk dump.

11110000 F0 Exclusive status

01000011 43 YAMAHA ID

0010nnnn 2n When n is received n=0~F, whichever is received.

When n is transmitted n always=0.

01001100 4C Model ID of XG

0aaaaaaa aaaaaaa Address High

0aaaaaaa aaaaaaa Address Mid

0aaaaaaa aaaaaaa Address Low

11110111 F7 End of Exclusive

For more information on the “Address” field, refer to the attached table.

In the attached tables “TOTAL SIZE” partitions a data series into single bulk

dumps. The “address” is the first byte of the bulk data.

3.Realtime Messages

3.1 Active Sensing

a) Transmission

Transmitted approximately once every 200msec.

b) Reception

If no MIDI data is received within 400ms following receipt of FE, the unit

executes processing equivalent to ALL SOUND OFF, ALL NOTES OFF, and

RESET ALL CONTROLLERS, then clears any remaining FEs.

3.2 MIDI Clock

a) Transmission

Transmitted as 1/96 clocks.

b) Reception

If the [MIDI 1] clock function is set to the External mode it will receive a

resolution of 1/96 clocks.

3.3 Start/Stop

If the [MIDI 2] function Start/Stop filter is ON transmission and reception are

disabled.

a) Transmission

All rhythm start and stop signals are transmitted.

b) Reception

When the relative message is received, the rhythm or song will start or stop.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha CVP-69 Seite 130

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha CVP-69

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info