Bedienungsanleitung Yamaha CVP-96 (Seite 124 von 164) (Englisch)

599408

124

Zoom out

Zoom in

Vorherige Seite

1/164

Nächste Seite

122

CVP-98/96/600

Press the TRACK EDIT button in the RECORD [EDIT] display to

call up the TRACK EDIT display. There are three pages in the TRACK

EDIT display: TRACK EDIT [MIX], TRACK EDIT [DELETE], and

TRACK EDIT [QUANTIZE].

Track Edit

Track Copy

• Only tracks containing data will appear

and can be selected for

TRACK A

and

TRACK B

. In addition, “- - -” (no track)

can also be selected for

TRACK B

. In

this case, the data of

TRACK A

will

simply be copied to

TRACK C

• For the Track Mix function, the se-

lected track voice and volume data,

etc. (i.e., all data except note data) of

TRACK A

will be effective for the track

after the mix operation.

■ Track Mix — Track Edit Page 1

The Track Mix function combines the data from two specified tracks

and copies the result to a third specified track.

Song Recording

ZSpecify the two tracks to be mixed..............................................

Press the TRACK A and TRACK B buttons to highlight the param-

eters, and use the data dial or [–/+] buttons to select the two track num-

bers to be mixed. The voices which are used for the selected tracks are

indicated at the side of A:/B:, located at the left of the LCD display.

XSpecify the destination track. .............................................................

Use the TRACK C parameter to specify the track to which you want

to record the mixed data. You can also specify the track for the mixed

data by highlighting the appropriate section using the TRACK C button,

then using the data dial or [–/+] buttons.

Any previous data in the destination track will be erased.

CExecute the Track Mix operation. ...................................................

Press the MIX button to begin execution of the Track Mix operation.

An “Are you sure?” confirmation prompt will appear. Press YES to ex-

ecute the Track Mix operation or press NO to cancel.

When this is completed, the MIX button will change to UNDO, al-

lowing you to undo the Track Mix operation and restore the previous

data (before mixing).

Press the [REC] button (the lamp goes out) to exit the Track Mix

function.

You can also exit the Track Mix function by pressing the [EXIT]

button.

• The previous data of the mixed track

will remain even after executing Track

Mix. If the old data is not needed, you

should delete it. (See “Track Delete”

below.)

• A bar graph indicating the progress of

the Track Mix operation will appear

while the data is being processed.

• You can check if the results are as you

expected or not, by starting and stop-

ping playback with the [PLAY/STOP]

button before performing the

UNDO

operation.

• The Undo function cannot be used if

you’ve selected another track or exited

from this mode.

• The Undo feature cannot be used for

data recorded to internal RAM (see

page 127).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha CVP-96 Seite 124

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha CVP-96

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info