50913
113
Zoom out
Zoom in
Vorherige Seite
1/122
Nächste Seite
111
English
TROUBLESHOOTING
ADDITIONAL
INFORMATION
Remote control
Problem Cause Remedy
Refer to
page
There is noise
interference from
digital or high-
frequency equipment,
or this unit.
This unit is too close to digital or high-
frequency equipment.
Move this unit further away from such equipment.
The picture is
disturbed.
The video source uses scrambled or
encoded signals to prevent dubbing.
Playing back video software that has an anti-copy
signal or video signals with a lot of noise may
produce unstable images.
This unit suddenly
switches to the
standby mode.
The internal temperature has become too
high and the overheat protection circuitry
activated.
Wait until this unit cools down and then turn it back
on.
Monitor output fails. The wrong TV format is set. Press and hold down EXIT on the remote control for
5 seconds or longer to initialize Video settings.
71
Problem Cause Remedy
Refer to
page
The remote control
does not work or
function properly.
The remote control is being used at the
wrong distance or angle.
The remote control will function within a maximum
range of 6 m (20 ft) at no more than 30 degrees off-
axis from the front panel.
9
Direct sunlight or lighting (from an
inverter type fluorescent lamp, etc.) is
striking this unit’s remote control sensor.
Reposition this unit.
The batteries are weak. Replace all batteries.
4
The manufacturer code was not set
correctly.
Set the manufacturer code correctly.
81
Try setting another code for the same manufacturer.
81
Even if the manufacturer code is correctly
set, there are some models that do not
respond to the remote control.
Program the necessary functions independently for
the programmable buttons using the learn feature.
82
The remote control
does not “learn” new
functions.
The batteries of this remote control and/or
the remote control for your component are
too weak.
Replace the batteries.
4
The distance between the two remote
controls is too long or too short.
Place the remote controls at the proper distance.
82
Signal coding or modulation of the remote
control for your component is not
compatible with this remote control.
Learning is not possible.
Memory capacity is full. Delete unnecessary functions to make room for new
functions.
86, 87
00EN.00_DSPZ9_GB.book Page 111 Thursday, November 13, 2003 10:55 AM
113

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yamaha DSP-Z9 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Yamaha DSP-Z9

Yamaha DSP-Z9 Bedienungsanleitung - Deutsch - 362 seiten

Yamaha DSP-Z9 Bedienungsanleitung - Holländisch - 482 seiten

Yamaha DSP-Z9 Bedienungsanleitung - Französisch - 362 seiten

Yamaha DSP-Z9 Bedienungsanleitung - Italienisch, Spanisch, Schwedisch - 482 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info