Bedienungsanleitung Yamaha DVDC996 (Seite 33 von 38) (Englisch)

30889

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

INTRODUCTIOIN PREPARATIONS PLAYBACK SETUP MENU

APPENDIX

English

APPENDIX

TROUBLESHOOTING

If this unit fails to operate normally, check the following points to determine whether the fault can be corrected, or if the fault

is not listed in the PROBLEM column, disconnect the power code and contact your authorized YAMAHA dealer or service

center.

■ General

PROBLEM POSSIBLE CAUSE WHAT TO DO

Refer to

Page

This unit fails to turn

on when the POWER

switch is pressed.

The power cord is not connected or the plug

is not completely inserted.

Firmly connect the power cord. —

The voltage selector on the rear panel is not

set to the proper position.

Disconnect the power cord and set the

selector to the position for your local main

voltage.

—

This unit does not work

normally.

This unit is affected by an external shock

(lightning, excessive static electricity,

incorrect operation, etc.)

Turn the power off and disconnect the power

cord. After about 30 seconds have passed,

connect the power and operate the unit again.

—

Playback does not

start.

The disc is damaged. Check the disc carefully; replace it if

necessary.

—

There is moisture on the laser pickup. Wait 20 to 30 minutes after switching the unit

ON before trying to play a disc.

—

The disc has been loaded upside down. Reload the disc with the label side facing up. 13

The disc is dirty. Clean the disc. 3

Play is delayed, or

starts at the wrong

place.

The disc may be scratched or damaged. Check the disc carefully; replace it if

necessary.

—

No sound. Incorrect output cable connections. Connect the cables properly. If the problem

persists, the cables may be defective.

Incorrect amplifier operation. Set the amplifier controls to the correct input

selection.

—

Sound distorted. V.S.S effect is emphasized too much. Turn V.S.S. off. 24

This unit is being subjected to vibrations or

impacts.

Relocate the unit. —

The disc is dirty. Clean the disc. 3

Sound ‘hums’. Incorrect cable connections. Securely connect the audio cables. If the

problem persists, the cables may be defective.

Noise from a nearby

tuner.

The tuner is too close to the unit. Place the tuner and the unit farther apart. —

Noise from inside of

the unit.

The disc maybe warped. Replace the disc. —

The batteries are weak. Replace all batteries with new ones. 7

Sound ‘skips’.

The remote control

does not work.

Direct sunlight or lighting (from an inverter

type of fluorescent lamp, etc.) is striking the

remote control sensor of this unit.

Relocate the unit. 7

No picture. Incorrect video connections. Connect this unit and other equipment

properly.

This unit’s video input is not selected at the

video monitor.

Set the video input at the video monitor to the

position where this unit is connected (e.g.

VCR2).

—

This unit does not

recognize discs (‘No

disc’ appears on the

display, or the display

shows the status when

no disc is loaded).

The disc(s) is not placed properly. Place the disc(s) correctly along the guide(s). —

107-C996(E)31-35 7/31/0, 4:17 PM31

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha DVDC996 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info