Bedienungsanleitung Yamaha EMX 512 (Seite 21 von 36) (Englisch)

484104

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Controls and Connectors

EMX512SC/EMX312SC/EMX212S

6 COMP knob (EMX512SC and EMX312SC only)

This knob adjusts the level of compression applied to the

channel. As the knob is turned to the right, the mixer

automatically raises the compression ratio while adjust-

ing the output gain accordingly. The result is a narrower,

more even dynamic range, as louder signals are softened

while the overall level is boosted. Avoid setting the knob

too high, however, as excess compression may lead to

howling.

7 LINE/MIC switch (Channels 1 to 4)

Set this switch to match the type of input signal you are

supplying—either a mic-level (low level) signal or a

line-level (high level) signal. Set the switch to LINE

() if you are connecting a line-level source, such as a

keyboard or audio device. Set it to MIC ( ) if you are

connecting up a microphone or other mic-level source.

To avoid damage to speakers, be sure to turn off the

power to the EMX itself and to any other power ampli-

ﬁers and power speakers before setting this switch to

LINE or MIC. We also recommend that you turn all

output controls (LEVEL knobs, MASTER knobs, etc.)

to minimum settings before operating the switch, to

avoid risk of loud noises that could cause hearing loss

or device damage.

8 INPUT A and INPUT B jacks (Channels 1 to 4)

You can connect an input source to either jack. Be sure

to set the LINE/MIC switch 7 to match the type of

device you are connecting.

INPUT A: TRS phone-type balanced line input (T:

hot, R: cold, S: ground). Accepts both bal-

anced and unbalanced line input.

INPUT B: XLR balanced mic input (1: ground, 2:

hot, 3: cold). If you are connecting a con-

denser microphone, be sure to turn the

PHANTOM switch P to its ON position.

•You cannot use both jacks at the same time.

• The signal into an INPUT jack is sent in equal lev-

els to the MAIN L and MAIN R buses.

9 LINE and MIC jacks (Channels 5/6 to 11/12)

These jacks accept stereo inputs. Use these to connect up

stereo output devices, such as stereo synthesizers and

CD players.

LINE jacks: Unbalanced stereo inputs. On channel

pairs 5/6 and 7/8 these are phone jacks; on

channel pairs 9/10 and 11/12 they are

RCA pin jacks.

MIC jack: XLR balanced stereo mic-level input jack.

If you are connecting a condenser micro-

phone, be sure to turn the PHANTOM

switch P to its ON position.

• If you wish, you may use the channel pair’s LINE

and MIC jacks together at the same time. But note

that the levels cannot be adjusted independently.

• Signals into LINE L and LINE R jacks are sent

independently to the corresponding MAIN L and R

buses.

• The signal into a MIC jack is sent in equal levels to

the MAIN L and MAIN R buses.

R: Cold (–)

S: Ground T: Hot (+)

Cold (–)

Ground Hot (+)

NOTE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha EMX 512 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info