Bedienungsanleitung Yamaha EMX 512 (Seite 25 von 36) (Englisch)

484104

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Controls and Connectors

EMX512SC/EMX312SC/EMX212S

POWER Section

P PHANTOM switch

This switch toggles +15V phantom power on and off. If

you set the switch on, the mixer supplies power to the

XLR mic input jacks on all channels (the INPUT B jacks

on channels 1 to 4, and the MIC jacks on channel pairs

5/6 to 11/12). Set this switch on when using one or more

condenser microphones.

When this switch is on, the mixer supplies DC +15V

power to pins 2 and 3 of all XLR input jacks.

• Be sure to leave this switch off if you do not need

phantom power.

• When using phantom power, do not connect any

devices other than condenser microphones to the

XLR input jacks. Other devices may be damaged if

connected to phantom power. This precaution does

not apply to balanced dynamic microphones, how-

ever, as these will not be affected by phantom power.

• To avoid damage to speakers, be sure to turn off the

power to the EMX itself and to any other power

ampliﬁers and power speakers before switching

phantom power on or off. We also recommend that

you turn all output controls (LEVEL knobs, MAS-

TER knobs, etc.) to minimum settings before operat-

ing the switch, to avoid risk of loud noises that could

cause hearing loss or device damage.

Q LIMITER lamps

The lamp lights up when the ampliﬁed signal being output at

the corresponding SPEAKERS jack hits its maximum value.

The lamp indicates that the limiter has come on.

If the lamps are ﬂashing frequently, the load on the amp

is too high and there is risk of damage to your equip-

ment. Reduce the setting of the MASTER knobs (

and M) until the lamps ﬂash only brieﬂy or not at all.

R POWER AMP switch

Selects the output that gets sent to the SPEAKERS jacks, as

follows.

Up (MAIN L/R):

SPEAKERS jacks A1 and A2 output the signal from

the MAIN L bus, and SPEAKERS jack B1 and B2

output the signal from the MAIN R bus. The MAIN

section’s MASTER knob G adjusts the output level at

all of the SPEAKERS jacks.

Down (MAIN(L+R)/MON):

SPEAKERS jacks A1 and A2 output a mix of the

signals from the MAIN L and MAIN R buses.

SPEAKERS jacks B1 and B2 output the signal

from the MONITOR bus. The MAIN section’s

MASTER knob G adjusts the level to the A jacks,

while the MONITOR section’s MASTER knob M

adjusts the level to the B jacks.

S YS Processing switch

This switch turns Yamaha Speaker Processing on or off.

The processor adjusts the speaker’s bass ranges so as to

compensate, for example, for lack of subwoofers. Note

however that the resulting frequency balance will vary

according to the speakers you are using.

T STAND-BY switch

This switch mutes the input to channels 1 to 8. The

switch lights up to indicate that the mute has been turned

on. Note that the mute does not work on channels 9 to 12.

When using the mixer for live performances, you can

ﬁll in gaps in the performance by turning on the

standby switch and feeding background music from a

CD player or other such device into channels 9 to 12.

U POWER switch and lamp

This switch turns the EMX power ON and OFF. The

lamp lights up to indicate that the power in on.

Before turning the power ON or OFF, be sure to turn

both MASTER knobs (

G and M) to “0”.

NOTE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha EMX 512 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info