Bedienungsanleitung Yamaha EMX 640 (Seite 6 von 16) (Englisch)

692373

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Front and rear panel

EMX640—Owner’s Manual

Input/output panel

Channel input jacks (Hi-Z, Lo-Z) 1~4

These are the input jacks for channels 1~4. By

using the PAD switches (control panel

) you

can connect any of the jacks to a wide range of

sources from mics to line level devices (synthesiz-

ers or rhythm boxes etc.). The Lo-Z jacks can

provide +48 V phantom power, allowing you to

use condenser microphones.

Both Hi-Z and Lo-Z are balanced, and are com-

patible with microphones of output impedance

50~600

Ω

or line level devices of 600

Ω

. The nom-

inal input level is –40 dB~–10 dB for the Hi-Z

jacks, and –50 dB~–20 dB for the Lo-Z jacks.

Pin connections for the Hi-Z and Lo-Z jacks are

as follows.

Channel input jacks (MIC/LINE) 5~6

These are the input jacks for channels 5~6.

Microphones can be connected to the MIC jacks,

and stereo line level devices (such as synthesizers

or rhythm boxes) can be connected to the LINE

jacks.

The MIC jacks are balanced, and are compatible

with microphones of output impedance

50~600

Ω

. The LINE jacks are unbalanced, and

are compatible with line level devices of 600

Ω

output impedance. Nominal input level is –50 dB

for the MIC jacks and –20 dB for the LINE jacks.

Effect output jack (EFFECT OUT)

The input of an external effect such as a delay or

echo can be connected to this jack. The signal

adjusted by the EFFECT control of each channel

will be sent to the EFFECT bus, its level adjusted

by the EFFECT OUT control, and output from

this jack.

The nominal output level and impedance are

+4 dB/10 k

Ω

Foot switch jack (FOOT SW)

A separately sold Yamaha FC5 foot switch can be

connected to this jack. If a foot switch is con-

nected to this jack, you can use your foot to

switch the built-in digital effect on/off. The Digi-

tal Effect ON switch on the front panel must be

set to ON in order to use a foot switch.

External input jacks (AUX IN/TAPE IN)

These are input jacks that allow the signal from

an external device to be added to the MAIN out-

put. Monaural output devices such as external

effects can be connected to the AUX IN jack, and

stereo output devices such as cassette recorder or

CD players can be connected to the TAPE IN

jacks.

INPUT TO MAIN OUTPUT

MONITOR

MAIN

AUX IN

REC

OUT

TAPE

EFFECT OUT

FOOT SW

LINEHi-Z LINE

MIC MICLo-Z

Hi-Z

Lo-Z

Hi-Z

Lo-Z

Hi-Z

Lo-Z

SEE REAR PANEL CAUTION

5 6

Lo-Z jacks

(XLR type)

Hi-Z jacks

(TRS phone jacks)

Pin 1: ground Sleeve: ground

Pin 2: hot (+) Tip: hot (+)

Pin 3: cold (–) Ring: cold (–)

Note: It is not possible to simultaneously use

both the Hi-Z and Lo-Z inputs of a given chan-

nel. For each channel, use only one of the inputs

as appropriate for the input source.

Phantom power is switched on/off in simulta-

neously for channels 1~6. For this reason,

devices which do not require phantom power

must be connected to the Hi-Z or LINE jacks if

the PHANTOM +48 V switch (control panel

L) is on.

GND

RST

GND

Note: It is possible to simultaneously use both

the MIC and LINE inputs for a given channel.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha EMX 640 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info