Bedienungsanleitung Yamaha ES8 (Seite 278 von 300) (Englisch)

48744

278

Zoom out

Zoom in

Vorherige Seite

1/300

Nächste Seite

Display Messages

278 Owner’s Manual

Appendix

No response from USB device

There is no response from the USB device connected to the USB TO DEVICE terminal.

No sample data. This message appears when a sample-related Job cannot be executed because the speciﬁed sample is not available.

Not empty folder You have attempted to delete a folder that contains data.

Now checking plug-in board. The MOTIF ES is checking the Plug-in board installation status during power-on.

Now loading... (xxxx) Indicates that a ﬁle is being loaded.

Now saving... (xxxx) Indicates that a ﬁle is being saved.

Now scanning auto loaded ﬁles Scanning for the ﬁles speciﬁed for Auto Load.

Now working... Executing the memory arrangement after ﬁnishing Sampling or canceling the Load/Save operation by pressing the

[EXIT] button.

Overwrite? [YES]/[NO] A save operation will overwrite data on the SmartMedia/USB storage device, and this message conﬁrms whether it is OK

to continue or not. Press [INC/YES] or [DEC/NO] as required.

Pattern length mismatch. A Pattern Job will result in the length of a Pattern being greater than 256 measures.

Phrase length mismatch A Pattern Job will result in the length of a phrase being greater than 256 measures.

Phrase number overﬂow The maximum number of phrases (256) has been exceeded when recording, executing a Pattern Job, or editing.

Please keep power on.

The data is being written to Flash ROM.

Never attempt to turn off the power while data is being written to Flash ROM. Turning the power off while this message is

shown results in loss of all user data and may cause the system to freeze (due to corruption of data in the Flash ROM).

This may also result in the MOTIF ES being unable to properly start up the next time the power is turned on.

Please stop sequencer. The operation you’ve attempted to execute cannot be done during Song/Pattern playback.

PLG100 not supported. The Plug-in All Bulk Save function does not apply to the PLG100 series boards.

Plug-in1 communication error. The Plug-in board that has been installed to slot 1 does not work.

Plug-in1 type mismatch. The User Voice created by using the Plug-in board previously installed to slot 1 (but now removed from the slot) has been

selected.

Plug-in2 communication error. The Plug-in board that has been installed to slot 2 does not work.

Plug-in2 type mismatch. The User Voice created by using the Plug-in board previously installed to slot 2 (but now removed from the slot) has been

selected.

Plug-in3 communication error. The Plug-in board that has been installed to slot 3 does not work.

Plug-in3 type mismatch. The User Voice created by using the Plug-in board previously installed to slot 3 (but now removed from the slot) has been

selected.

Power on mode stored The setting of the program number automatically selected when turning the power on has been stored.

Receiving MIDI bulk The MOTIF is receiving MIDI bulk data.

Sample freq is too low. The sampling frequency is too low and the Frequency Convert Job cannot be executed.

Sample is protected. The sample cannot be overwritten because it is protected.

Sample is too long. The sample size is too large and the Time Stretch Job cannot be executed.

Sample is too short. The sample length is too short and the Frequency Convert Job cannot be executed.

Sample memory full. The sample memory is full and further sampling operations, Jobs, or load operations cannot be executed.

Scene & Arpeggio type stored The Song Scene and current Arpeggio type has been stored to one of the [SF1] - [SF5] buttons.

Seq memory full. The internal memory for Sequence data is full, preventing any further operation (such as recording, editing, Job

execution, MIDI reception/transmission, or loading from the SmartMedia/USB storage device). Try again after erasing

unwanted Song, Pattern, or User phrase data.

System memory crashed. Writing data to Flash ROM has failed.

This performance uses user voices. The performance you have loaded includes User voice data. Check whether the voice you saved exists at the

appropriate User voice bank.

Too many favorites You’ve attempted to assign more than 257 voices to the Favorite category.

Too many ﬁxed notes When converting the song or pattern data to the Arpeggio data, the amount of different notes in the data to be converted

has exceeded sixteen.

Too many samples. The maximum overall number of samples (8192) has been exceeded.

Transmitting MIDI bulk The MOTIF ES is transmitting MIDI bulk data.

USB connection terminated. Press

[ENTER]. A break in the connection with the USB storage device has occurred because of an abnormal electric current.

Disconnect the USB storage device from the USB TO DEVICE connector, then press the [ENTER] button.

USB device connecting Recognizing the USB storage device connected to the USB TO DEVICE terminal.

USB power consumption exceeded. The power consumption of the USB storage device connected to the USB TO DEVICE connector exceeds the regulated

value.

USB transmission error An error occurs when communicating with the USB storage device.

Utility stored The settings in the Utility mode have been stored.

LCD Indication Explanation

Yamaha ES8 Seite 278

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha ES8

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info